Nokia 7088 Instrucciones de funcionamiento

Nokia Customer Care

7088 (RM-219)

Mobile Terminal

Antenna Description and

Troubleshooting

7088 (RM-219)

Antenna Description and Troubleshooting

Contents Page

Introduction................................................................................................................3

Visual Quality Requirements.............................................................................3

Failures and Corrective Measures............................................................................3

Internal Antenna................................................................................................4

Damage of the antenna feeding pins.................................................................4

Obstruction of the RF signal path..............................................................................5

RF Connector Failure........................................................................................6

7088 (RM-219)

Nokia Customer Care Antenna Description and Troubleshooting

Introduction

The mobile terminal incorporates an internal antenna. This antenna arrangement is

used for Cellular frequency bands. The internal antenna assembly adopts planar

inverted-F antenna (PIFA) structure used for the cellular engine, and it is embedded

invisibly in a mechanical part.

Visual Quality Requirements

Followings are the minimum acceptable visual quality requirements of the internal

antenna assembly:

 No visual cracks or mechanical defects.

 No oil, dirt, or particles on the parts.

 No paint drops on the mechanical appearance.

 Good elasticity for two feeding pins (signal and ground pins).

 Invisibility for the antenna at any condition.

Failures and Corrective Measures

Figure 1 shows the D Cover antenna assembly. The internal antenna is a sticker

type flex film mounted on the D Cover, and there is an antenna decoration on top of

it. D Cover, antenna, and antenna decoration are with the same color (shown in

Figure 1 are all black). Thus, ideally the antenna is invisible.

 If the appearance of the antenna decoration looks damaged or peeled off,

replace it with a new antenna decoration.

Antenna zone

 If the antenna can be seen at some condition, remove the current antenna

decoration, and stick a new one on its proper position.

Antenna decoration

D Cover

Figure 1: D Cover Assembly

7088 (RM-219)

Antenna Description and Troubleshooting

Internal Antenna

The internal antenna receives and transmits the signal by the contact between two

feeding pins of the D Cover and the feeding pads on the PWB. Figure 2 shows the

feeding pins (signal and ground pins) and their corresponding feeding pads. Two

feeding pins must contact fully with their corresponding pads on the PWB. If one of

the connections is malfunction, the antenna performance could be degraded by

more than 20dB.

Signal pin Ground pin Ground pad Signal pad

Figure 2: The connection structure for D Cover assembly and PWB

Damage of the antenna feeding pins

The two feeding pins must properly connect to their corresponding pads on the

PWB.

 If one of the connections is malfunction, the antenna performance could

be degraded by more than 20dB.

 If one of these two pins lacks for elasticity, change the D Cover assembly.

 If the DC resistance between these two pins is more than 0.5 ohm,

change the D Cover assembly.

 If one of these two feeding pins is broken or bent, change the D Cover

assembly.

7088 (RM-219)

Nokia Customer Care Antenna Description and Troubleshooting

Obstruction of the RF signal path

If the RF signal path is obstructed, broken, damaged, the cellular antenna

performance degrades.

 If the obstruction, damage of signal path happens, replace the PWB.

 If one of the components at the matching circuit is missing, broken,

replace proper component according to the latest reference document.

 If the DC resistance between signal pad and the output port of RF switch

is more than 1 ohm, replace the PWB.

Figure 3: PWB layout of RF feeding path

Signal pad Output port of RF switch

Matching circuit

7088 (RM-219)

Antenna Description and Troubleshooting

RF Connector Failure

The RF connector fails when it does not properly connect the RF input terminal to

the RF output terminal during the SMT. If this happens the antenna gain degrades

by 25 dB. Check this by testing the resistance value between the RF input and RF

output ports of the RF connector and see if the value is close to zero. If the RF input

is not connected properly to the RF output, replace the RF connector.

Note: Perform the resistance value test without a RF cable attached to the RF

connector. Because the RF connector is also a switch, the RF output is

disconnected from the RF input when a RF cable is inserted into the RF connector.

 RF input terminal – connect to duplexer.

 RF output terminal – connect to the antenna pad through antenna

matching circuit.

 RF connector terminal – connect to a RF coaxial cable.

RF output terminal RF input terminal

RF input terminal

Figure 4: RF input / output terminal

Note:

• MSM6025 is underfilled and cannot be replaced.

• Memory IC is underfilled and cannot be replaced.

• The Baseband Shielding Cover Assy and RF Shielding Cover cannot be

reused after removal.

• After using the heatgun, replace the domesheet

Otros manuales para 7088

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Portátil de Nokia

Nokia

Nokia 6088 Guía

Nokia

Nokia RM-429 Manual de usuario

Nokia

Nokia RH-77 Guía de inicio rápido

Nokia

Nokia 6088 Guía de inicio rápido

Nokia

Nokia 7088 Instrucciones de funcionamiento

Nokia

Nokia 6255 Guía

Nokia

Nokia 7088 Guía de inicio rápido

Nokia

Nokia RM-801 Manual de usuario

Nokia

Nokia RM-555 Manual de usuario

Nokia

Nokia RH-77 Instrucciones de funcionamiento

Nokia

Nokia RM-849 Manual de usuario

Nokia

Nokia 301 Manual de usuario

Nokia

Nokia RM-626 Manual de usuario

Nokia

Nokia RM-609 Manual de usuario

Nokia

Nokia 6120 classic Manual de usuario

Nokia

Nokia RH-99 Manual de usuario

Nokia

Nokia 6255 Guía

Nokia

Nokia 2608 Manual de usuario

Nokia

Nokia 2125 Instrucciones de funcionamiento

Nokia

Nokia 2730 Classic RM-579 Manual de usuario

Nokia

Nokia 1265 Guía

Nokia

Nokia RM-761 Manual de usuario

Nokia

Nokia RH-66 Instrucciones de funcionamiento

Nokia

Nokia 1265 Guía de inicio rápido

Manuales populares de Portátil de otras marcas

Honeywell

Honeywell Dolphin 9900 Manual de usuario

Honeywell

Honeywell CN75 Manual de usuario

MiTAC

MiTAC Mio 168 Manual de usuario

Wasp

Wasp WDT92 Manual de usuario

Texas Instruments

Texas Instruments TI-Nspire Manual de usuario

AXEM Technology

AXEM Technology MBS Manual de usuario

Armstrong

Armstrong Brain Wave Instrucciones de montaje

Unitech

Unitech TB128 Manual de usuario

Symbol

Symbol MC9000-G Manual de instalación y operación

Unitech

Unitech HT1 1D Batch Manual de usuario

Ingenico

Ingenico IWL220 GPRS Manual de usuario

Intermec

Intermec CK61 Manual de usuario

Symbol

Symbol c2000 Manual de usuario

Symbol

Symbol MC18 Manual de instalación y operación

Acer

Acer n20 Manual de usuario

Intermec

Intermec CK61 Manual de usuario

Docomo

Docomo F-04H Manual de usuario

Toshiba

Toshiba e350 Series Manual de usuario