Noctua NH-U14S Manual de usuario

Required mounting parts:

Dear customer,

Congratulations on choosing the Noctua NH-U14S.

The NH-U14S is the first 140mm model in Noctua’s award-winning

NH-U series. First introduced in 2005, the NH-U series has be-

come a standard choice for premium quality quiet CPU coolers and

won more than 400 awards and recommendations from leading

international hardware websites and magazines.

Enjoy your NH-U14S!

Yours sincerely,

Roland Mossig, Noctua CEO

This manual will guide you through the installation process of the

SecuFirm2™ mounting system step by step. Prior to installing

the cooler, please consult the compatibility list on our website

(www.noctua.at/compatibility) and verify that the cooler is fully

compatiblewithyourmotherboard.Shouldyouencounteranydiffi-

culties,pleasechecktheFAQsonourwebsite(www.noctua.at/faqs)

and don’t hesitate to contact our support team at

support@noctua.at. Noctua cannot be held responsible for any

damage or losses caused by compatibility issues.

Multilingual versions of this manual are available on our website:

www.noctua.at/manuals

Removing the mainboard

In case you want to use the cooler on an assembled system and

your case doesn’t have a cut-out at the rear side of the mainboard

tray, you first have to remove the mainboard from the case in

order to be able to install the supplied backplate.

Step 1

Caution: Make sure that the curved sides of the mounting bars are

pointing outwards.

2x NM-IMB3 Mounting Bars1x NM-IBP2 Backplate

4x NM-ITS1 Thumbscrews4x NM-IPS1 Spacers

Applying thermal paste

If there are residual traces of thermal paste or thermal pads on

your CPU, please clean them off first. Then press a small drop

(4-5mm diameter) of NT-H1 onto the centre of the heatspreader.

Caution: Applying too much thermal paste will lower heat

conductivity and cooling performance!

Step 4

Place the backplate on the rear side of the mainboard so that the

bolts stick through the mounting holes.

Caution: Please make sure that the three cut-outs in the

supplied backplate align with the screws of the mainboard’s stock

backplate.

Installing the mounting bars

Caution:

Choose the alignment of the mounting bars according to the desired

final orientation of the cooler:

Step 3

First put the plastic spacers onto the bolts of the backplate, then

add the mounting bars.

Fix the mounting bars using the 4 thumb screws.

Caution: Gently tighten the screws until they stop, but don’t use

excessive force.

Attaching the backplate

Caution: The supplied backplate will install over the mainboard’s

stock backplate, so the mainboard’s stock backplate must not be

taken off.

Step 2

Orientation A Orientation B

Fastening the heatsink to the CPU

Caution: Please first take off the fan as well as the protection cover

at the bottom side of the heatsink.

Step 5

Noctua NH-U14S | Installation Manual | LGA115x

LGA115x

Then put the heatsink onto the CPU and screw it to the screw

threads of the mounting bars.

Caution: Tighten the screws until they stop.

Adding a second fan

The NH-U14S includes an extra set of fan clips and an extra set of

thicker anti-vibration pads for installing a second NF-A15 fan in

push/pull mode in order to further improve cooling performance.

Please use the thicker anti-vibration pads on the rear NF-A-15 fan

for improved acoustics if space allows. The y-cable supplied with

the retail NF-A15 fan can be used to control the speed of both fans

via the same mainboard fan header.

Please note that while the NF-A15 fan included with the NH-

U14S runs at 1500rpm, Noctua recommends using the standard

1200rpm retail version as a rear fan in push/pull mode as the

combination of 1500rpm at the front and 1200rpm at the rear

will provide the best balance of performance and acoustics.

If you would like to run both fans at the same speed, please use

the supplied Low-Noise Adaptor on the front fan to reduce the

speed to 1200rpm.

Even with high-grade products and strict quality control, the pos-

sibility of defects cannot be eliminated entirely. Therefore, we aim

at providing the highest possible level of reliability and conveni-

ence by offering a warranty period of 6 years and direct, fast and

straightforward RMA service.

Should you encounter any problems with your NH-U14S, please

don’t hesitate to contact our support team ([email protected]).

Please also consult the FAQ section on our website:

www.noctua.at/faqs.

Warranty, Support and FAQs

Clip position for thick spacers:

Clip position for standard spacers:

Connect the fan to the mainboard’s CPU fan header.

Depending on your CPU and the temperature inside the case, you

may interconnect the supplied NA-RC7 Low-Noise Adapter (L.N.A.)

in order to further reduce the fan’s operating noise.

Caution: When using the L.N.A., check the temperature of your

CPU using appropriate software (e.g. the respective applications

of your mainboard manufacturer), in order to evade automatic

throttling of the CPU due to the increased temperature. If the cool-

ing performance is insufficient, please increase case ventilation or

remove the L.N.A.

Reattach the fan to the heatsink using the supplied steel clips:

Fan Setup

Step 6

While Noctua recommends using an NF-A15 fan for best results in

dual fan mode, the extra set of fan clips can also be used to install

most other fans. In this case, please put the supplied self-adhesive

anti-vibration strips onto the heatsink to avoid vibrations being

transmitted to the cooler.

1. Remove standard spacers on rear fan

2. Install thick spacers on rear fan

Airflow

front fan (standard spacers)

rear fan (thick spacers)

Noctua NH-U14S | Installation Manual | LGA115x

LGA115x

Installing the mounting bars

First screw the NM-IBT2 bolts into the screw threads of the

LGA2011 socket frame.

Step 1

Then put the NM-IMB2 mounting-bars onto the bolts.

Required mounting parts:

Dear customer,

Congratulations on choosing the Noctua NH-U14S.

The NH-U14S is the first 140mm model in Noctua’s award-winning

NH-U series. First introduced in 2005, the NH-U series has be-

come a standard choice for premium quality quiet CPU coolers and

won more than 400 awards and recommendations from leading

international hardware websites and magazines.

Enjoy your NH-U14S!

Yours sincerely,

Roland Mossig, Noctua CEO

This manual will guide you through the installation process

of the SecuFirm2™ mounting system step by step. Prior to

installing the cooler, please consult the compatibility list on

our website (www.noctua.at/compatibility) and verify that the

cooler is fully compatible with your motherboard. Should you

encounter any difficulties, please check the FAQs on our website

(www.noctua.at/faqs) and don’t hesitate to contact our support

team at support@noctua.at. Noctua cannot be held responsible

for any damage or losses caused by compatibility issues.

Multilingual versions of this manual are available on our website:

www.noctua.at/manuals

NM-IBT2 Bolts

4x NM-ITS1 ThumbscrewsNM-IMB3 Mounting Bars

Caution: Choose the alignment of the mounting bars according to

the desired final orientation of the cooler:

Orientation A Orientation B

Caution: Make sure that the curved sides of the mounting bars are

pointing outwards.

Fix the mounting bars using the 4 thumb screws.

Caution: Gently tighten the screws until they stop, but don’t use

excessive force.

Applying thermal paste

If there are residual traces of thermal paste or thermal pads on

your CPU, please clean them off first. Then press a small drop

(4-5mm diameter) of NT-H1 onto the centre of the heatspreader.

Caution: Applying too much thermal paste will lower the heat

conductivity and cooling performance!

Step 2

Fastening the heatsink to the CPU

Caution: Please first take off the fan as well as the protection cover

at the bottom side of the heatsink.

Step 3

Then put the heatsink onto the CPU and screw it to the screw

threads of the mounting bars.

Caution: Tighten the screws until they stop.

Noctua NH-U14S | Installation Manual | LGA2011

LGA2011

Even with high-grade products and strict quality control, the pos-

sibility of defects cannot be eliminated entirely. Therefore, we aim

at providing the highest possible level of reliability and conveni-

ence by offering a warranty period of 6 years and direct, fast and

straightforward RMA service.

Should you encounter any problems with your NH-U14S, please

don’t hesitate to contact our support team ([email protected]).

Please also consult the FAQ section on our website:

www.noctua.at/faqs.

Warranty, Support and FAQs

Clip position for thick spacers:

Clip position for standard spacers:

Connect the fan to the mainboard’s CPU fan header.

Depending on your CPU and the temperature inside the case, you

may interconnect the supplied NA-RC7 Low-Noise Adapter (L.N.A.)

in order to further reduce the fan’s operating noise.

Caution: When using the L.N.A., check the temperature of your

CPU using appropriate software (e.g. the respective applications

of your mainboard manufacturer), in order to evade automatic

throttling of the CPU due to the increased temperature. If the cool-

ing performance is insufficient, please increase case ventilation or

remove the L.N.A.

Reattach the fan to the heatsink using the supplied steel clips:

Fan Setup

Step 4

While Noctua recommends using an NF-A15 fan for best results in

dual fan mode, the extra set of fan clips can also be used to install

most other fans. In this case, please put the supplied self-adhesive

anti-vibration strips onto the heatsink to avoid vibrations being

transmitted to the cooler.

Adding a second fan

The NH-U14S includes an extra set of fan clips and an extra set of

thicker anti-vibration pads for installing a second NF-A15 fan in

push/pull mode in order to further improve cooling performance.

Please use the thicker anti-vibration pads on the rear NF-A-15 fan

for improved acoustics if space allows. The y-cable supplied with

the retail NF-A15 fan can be used to control the speed of both fans

via the same mainboard fan header.

Please note that while the NF-A15 fan included with the NH-

U14S runs at 1500rpm, Noctua recommends using the standard

1200rpm retail version as a rear fan in push/pull mode as the

combination of 1500rpm at the front and 1200rpm at the rear

will provide the best balance of performance and acoustics.

If you would like to run both fans at the same speed, please use

the supplied Low-Noise Adaptor on the front fan to reduce the

speed to 1200rpm.

1. Remove standard spacers on rear fan

2. Install thick spacers on rear fan

Airflow

front fan (standard spacers)

rear fan (thick spacers)

Noctua NH-U14S | Installation Manual | LGA2011

LGA2011

Attaching the mounting bars

First put the plastic spacers onto the screw threads, then fix the

mounting bars using the 4 long screws.

Step 2

Required mounting parts:

Dear customer,

Congratulations on choosing the Noctua NH-U14S.

The NH-U14S is the first 140mm model in Noctua’s award-winning

NH-U series. First introduced in 2005, the NH-U series has be-

come a standard choice for premium quality quiet CPU coolers and

won more than 400 awards and recommendations from leading

international hardware websites and magazines.

Enjoy your NH-U14S!

Yours sincerely,

Roland Mossig, Noctua CEO

This manual will guide you through the installation process

of the SecuFirm2™ mounting system step by step. Prior to

installing the cooler, please consult the compatibility list on

our website (www.noctua.at/compatibility) and verify that the

cooler is fully compatible with your motherboard. Should you

encounter any difficulties, please check the FAQs on our website

(www.noctua.at/faqs) and don’t hesitate to contact our support

team at support@noctua.at. Noctua cannot be held responsible

for any damage or losses caused by compatibility issues.

Multilingual versions of this manual are available on our website:

www.noctua.at/manuals

2x NM-AMB3 Mounting Bars

4x NM-APS1 Plastic Spacers4x NM-ALS1 Screws

Caution: The SecuFirm2™ mounting system requires a back-

plate, which is preinstalled on most AMD mainboards. If your

mainboard doesn’t have a backplate, please contact our support

team at support@noctua.at.

Removing the retention module

If your mainboard uses a retention module for CPU cooler instal-

lation, please remove it first. The SecuFirm2™ mounting system

will install directly to your mainboard’s stock backplate on the rear

side of the socket.

Step 1

Caution: Make sure that the curved sides of the mounting bars are

pointing outwards.

Caution: Tighten the screws until they stop.

Applying thermal paste

If there are residual traces of thermal paste or thermal pads on

your CPU, please clean them off first. Then press a small drop

(4-5mm diameter) of NT-H1 onto the centre of the heatspreader.

Step3

Caution: Applying too much thermal paste will lower heat

conductivity and cooling performance!

Fastening the heatsink to the CPU

Caution: Please first take off the fan as well as the protection cover

at the bottom side of the heatsink.

Step 4

Then put the heatsink onto the CPU and screw it to the screw

threads of the mounting bars.

Caution: Tighten the screws until they stop.

AMD stock backplate

Noctua NH-U14S | Installation Manual | AM2

AM2

Even with high-grade products and strict quality control, the pos-

sibility of defects cannot be eliminated entirely. Therefore, we aim

at providing the highest possible level of reliability and conveni-

ence by offering a warranty period of 6 years and direct, fast and

straightforward RMA service.

Should you encounter any problems with your NH-U14S, please

don’t hesitate to contact our support team ([email protected]).

Please also consult the FAQ section on our website:

www.noctua.at/faqs.

Warranty, Support and FAQs

Clip position for thick spacers:

Clip position for standard spacers:

Connect the fan to the mainboard’s CPU fan header.

Depending on your CPU and the temperature inside the case, you

may interconnect the supplied NA-RC7 Low-Noise Adapter (L.N.A.)

in order to further reduce the fan’s operating noise.

Caution: When using the L.N.A., check the temperature of your

CPU using appropriate software (e.g. the respective applications

of your mainboard manufacturer), in order to evade automatic

throttling of the CPU due to the increased temperature. If the cool-

ing performance is insufficient, please increase case ventilation or

remove the L.N.A.

Reattach the fan to the heatsink using the supplied steel clips:

Fan Setup

Step 5

While Noctua recommends using an NF-A15 fan for best results in

dual fan mode, the extra set of fan clips can also be used to install

most other fans. In this case, please put the supplied self-adhesive

anti-vibration strips onto the heatsink to avoid vibrations being

transmitted to the cooler.

Adding a second fan

The NH-U14S includes an extra set of fan clips and an extra set of

thicker anti-vibration pads for installing a second NF-A15 fan in

push/pull mode in order to further improve cooling performance.

Please use the thicker anti-vibration pads on the rear NF-A-15 fan

for improved acoustics if space allows. The y-cable supplied with

the retail NF-A15 fan can be used to control the speed of both fans

via the same mainboard fan header.

Please note that while the NF-A15 fan included with the NH-

U14S runs at 1500rpm, Noctua recommends using the standard

1200rpm retail version as a rear fan in push/pull mode as the

combination of 1500rpm at the front and 1200rpm at the rear

will provide the best balance of performance and acoustics.

If you would like to run both fans at the same speed, please use

the supplied Low-Noise Adaptor on the front fan to reduce the

speed to 1200rpm.

1. Remove standard spacers on rear fan

2. Install thick spacers on rear fan

Airflow

front fan (standard spacers)

rear fan (thick spacers)

Noctua NH-U14S | Installation Manual | AM2

AM2

Otros manuales de Hardware de computadora de Noctua

Noctua

Noctua NF-F12 Manual de usuario

Noctua

Noctua NF-F12 5V PWM Manual de usuario

Noctua

Noctua NH-P1 Manual de usuario

Noctua

Noctua NH-U12S DX-4677 Manual de usuario

Noctua

Noctua NA-SAV4 Manual de usuario

Noctua

Noctua NH-U14S TR5-SP6 Manual de usuario

Noctua

Noctua NH-C12P SE14 Manual de usuario

Noctua

Noctua NH-U12S SE-AM4 Manual de usuario

Noctua

Noctua NH-U12S chromax.black Manual de usuario

Noctua

Noctua NM-A90 Manual de usuario

Noctua

Noctua NM-i4677 Manual de usuario

Noctua

Noctua NF-A14 PWM Manual de usuario

Noctua

Noctua NH-L9 65 Series Manual de usuario

Noctua

Noctua NH-D15 Manual de usuario

Noctua

Noctua NH-D9 TR5-SP6 4U Manual de usuario

Noctua

Noctua NH-U9 Series Manual de usuario

Noctua

Noctua NH-U12A Manual de usuario

Noctua

Noctua NF-A15 Manual de usuario

Noctua

Noctua NM-TR5-SP6 Manual de usuario

Noctua

Noctua NM-AM4 UxS Manual de usuario

Noctua

Noctua NF-A20 5V Manual de usuario

Noctua

Noctua NH-U9DO A3 Manual de usuario

Noctua

Noctua NH-U12DX i4 Manual de usuario

Noctua

Noctua NF-A6x25 5V PWM Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario