NKE WiMo Manual de usuario

nke Instrumentation – 6 rue Gutenberg, ZI de Kerandré, 56700 Hennebont, France

WiMo Calibration Tool

User Manual

Revision 1.0 (10/06/2021)

WiMo / WiMo Plus Multiparameters Sondes 1

Table of contents

TABLE OF CONTENTS ........................................................................................................................................ 1

1ABOUT THIS DOCUMENT ......................................................................................................................... 2

1.1 ASSISTANCE............................................................................................................................................... 2

1.2 DISCLAIMER............................................................................................................................................... 2

1.3 COPYRIGHT ............................................................................................................................................... 2

2INTRODUCTION........................................................................................................................................ 3

2.1 WIMO MULTIPARAMETER SONDE .................................................................................................................. 3

2.2 WIMO SENSOR AND CALIBRATION TOOL.......................................................................................................... 3

2.3 TECHNICAL REQUIREMENT ............................................................................................................................ 3

3QUICK START ........................................................................................................................................... 4

3.1 SENSOR AND INTERFACE CONNECTION ............................................................................................................ 4

3.2 START WITH WIMO CALIBRATION TOOL SOFTWARE .......................................................................................... 4

4START A NEW CALIBRATION .................................................................................................................... 5

4.1 DETECT THE SENSOR.................................................................................................................................... 5

4.2 RESET NKE FACTORY CALIBRATION.................................................................................................................. 6

4.3 START MEASUREMENT ................................................................................................................................. 7

4.4 ADD CALIBRATION POINTS ............................................................................................................................ 8

4.4.1 Calibration point manual add............................................................................................................ 8

4.4.2 Calibration point quick add ............................................................................................................... 9

4.5 SELECT THE CALIBRATION TYPE .................................................................................................................... 10

WiMo / WiMo Plus Multiparameters Sondes 2

About this document

1About this document

1.1 Assistance

Our aim is to provide customers with timely and comprehensive service. For any assistance, please

contact our company technical support:

nke Instrumentation

6 rue Gutenberg - ZI Kérandré

56700 Hennebont - FRANCE

+33 (0)2 97 36 41 31 – Fax +33 02 97 55 17

info.instrumenta[email protected]

https://nke-instrumentation.com/contact/

1.2 Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO

IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

nke Instrumentation, its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “nke Instrumentation”), disclaim any and all liability for any errors, inaccuracies or

incompleteness contained in any user manual or in any other disclosure relating to any product.

The information contained in this guide is subject to change without notice. nke Instrumentation

reserves the right to revise this documentation and to make changes in content from time to time

without obligation on the part of nke Instrumentation to provide notification of such revision or

change.

All pictures shown are for illustration purpose only. Actual product may vary due to product

enhancement.

nke Instrumentation provides this documentation as a service to its customers without warranty,

term, or condition of any kind, either implied or expressed, including, but not limited to, the implied

warranties, terms or conditions of merchantability, satisfactory quality, and fitness for a particular

purpose. nke Instrumentation, its employees and agents will not be responsible for any loss, however

arising, from the use of, or reliance on this information.

1.3 Copyright

The information contained here is proprietary technical information of nke Instrumentation.

Transmitting, reproduction, dissemination and editing of this document as well as utilization of the

content are forbidden without permission offenders will be held liable for payment of damages. All

rights are reserved in the event of patent grant or registration of utility model or design.

WiMo / WiMo Plus Multiparameters Sondes 3

Introduction

2Introduction

2.1 WiMo multiparameter sonde

The WiMo multiparameter range, including the WiMo sonde (4 locations) and the WiMo Plus sonde (7

locations), offers flexible and innovative solutions for water quality data collection. The sonde has a

native pressure sensor and temperature measurement and 4 to 7 additional sensors can be added

depending on the model. The end-user directly plugs the sensors to the sonde which are automatically

recognized (Plug and Play system). The sonde can also be connected to a transmission module that will

also be automatically detected.

Data can either be recorded in internal memory of the sonde or transmitted to a data collection

platform via the transmission modems. The sonde also operates in Modbus for real-time measurement

of the environment.

2.2 WiMo sensor and calibration tool

As mentioned in the previous part, the WiMo sensors are plug and play systems. It allows to calibrate

them independently of a WiMo Sonde. To achieved that, nke has developed an usb calibration tool

which connects a WiMo sensor to a computer. It works with a dedicated software named “WiMo

Calibration Tool”.

2.3 Technical requirement

The usb calibration tool and its software have been developed for Windows 7 and Windows 10. User

needs administrator rights on his computer to make the software work normally.

WiMo / WiMo Plus Multiparameters Sondes 4

Quick start

3Quick start

This part is an introduction about how to start using the usb sensor tool with WiMo Calibration Tool

software.

3.1 Sensor and interface connection

Plug the sensor to the usb calibration tool:

1 - Engage it in the location by making the coded pin coincide with the host hole in the usb tool,

2 - Screw the sensor locking sleeve in the clockwise direction.

Computer connection:

3 - Plug the usb calibration tool to the computer usb port.

3.2 Start with WiMo Calibration Tool software

If you have not downloaded the software yet, please click on the link bellow:

https://nke-instrumentation.support/Software/WiMo_Calibration_Tool/Lastest/WiMo_Calibration_Tool.zip

Place the zip file on the desktop and uncompress it.

You will have a folder containing the software:

Launch WiMo_Calibration_Tool.exe (double click on the executable file).

Software main window open.

WiMo / WiMo Plus Multiparameters Sondes 5

Start a new calibration

4Start a new calibration

4.1 Detect the sensor

1 - Click on the refresh button.

2 - Sensor informations are displayed.

WiMo / WiMo Plus Multiparameters Sondes 6

Start a new calibration

4.2 Reset nke factory calibration

A new sensor delivered from nke has already been calibrated.

To start new calibration, user has to remove and reset last one.

nke factory calibration can be removed in the calibration menu.

For a selected channel, user must set Calibration type to None and reset calibration point.

1 – Click on the calibration menu.

2 - Select the dedicated sensor channel on the “Channel selection” section.

3 - User has to set “Calibration type” to “None” in the calibration settings section.

4 - Calibration points can be all reset with “Delete all lines” button in the calibration points section.

WiMo / WiMo Plus Multiparameters Sondes 7

Start a new calibration

4.3 Start measurement

Measurement can be made in the “Live view” left menu section (1).

To start press the top on/off button (2).

WiMo / WiMo Plus Multiparameters Sondes 8

Start a new calibration

4.4 Add calibration points

Adding calibration points can be made with two methods:

-manual adding in the “Calibration” right menu section,

-quick add in the liveview advanced settings section.

4.4.1 Calibration point manual add

To add calibration point, go to the “Calibration” menu panel.

Firstly, user has to select the channel he wants to calibrate on the “Channel selection” section.

On the same page the last section named “Calibration points” allow to manage calibration point.

1 – Button “Add point”: open a pop-up (5) that allow to enter a new calibration point (Physical and

raw value).

2 – Button “Modify selected point”: after clicking on a row in calibration point table, user can modify

selected line calibration point in a popup (5).

3 – Button “Delete selected point”: after clicking on a row in calibration point table, selected points

will be removed from the sensor.

4 – Button “Delete all points”: delete all calibration points for the selected sensor channel.

WiMo / WiMo Plus Multiparameters Sondes 9

Start a new calibration

4.4.2 Calibration point quick add

On the Liveview section, on the top right user can find the “advanced settings” button (1).

It slides to a new panel with some liveview configuration parameters and new functionality.

Firstly, select the working channel (working channel selection section). New calibration points will be

added to this selected channel.

In the last section named “Add to calibration point”, you will be able to quickly add calibration point

to the sensor. However, it is necessary to stop measurement to submit new point.

Otros manuales para WiMo

Tabla de contenidos

Otros manuales de Instrumento de medición de NKE

NKE

NKE PIEZOMETER Manual de usuario

NKE

NKE SAMBAT Manual de usuario

NKE

NKE DualSense HeatPro Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario