Nivis VN210 Manual de usuario

VN210 RF Modem User’s Manual

Version 1.2

Created: May 18, 2009

Modified: Sept 2, 2009

User Manual

Proprietary & Confidential

Version 1.1

Revision History

Date Revision Description Author

05/18/2009 1.0 Document Creation Szabolcs Zigovszki

08/24/2009 1.1 Include new antennas Edward Castro

09/02/2009 1.2 Changed section 6 Edward Castro

User Manual

Proprietary & Confidential

Version 1.1

Table of Contents

1. Purpose of Document............................................................................................ 1

2. Overview of the Radio Modem Hardware............................................................. 1

3. Operation of the Nivis Radio Modem ................................................................... 4

3.1. Getting started ...................................................................................................... 4

4. RF Exposure Limit Warning ..................................................................................... 4

5. Compliance Statement (Part 15.19) ......................................................................... 4

6. OEM Responsibility to the FCC Rules and Regulations ........................................ 5

7. Warning (Part 15.21).................................................................................................. 5

User Manual

Proprietary & Confidential

Page 1

version 1.0

1. Purpose of Document

This document was created in order to provide to the user clear guidelines regarding the

usage of the VN210 RF modem.

2. Overview of the Radio Modem Hardware

The VN210 radio modem is an 802.15.4 wireless module that allows communication

using a standard asynchronous serial data stream. The pin-out of the VN210 radio

modem is presented in the figure below.

User Manual

Proprietary & Confidential

Page 2

version 1.0

No. Name Description Type Dir Comments

1 UART2-RTS UART2 Request to Send DIG I Can be configured as G IO

2 UART2-CTS UART2 Clear to Send DIG O Can be configured as G IO

3 UART2-RXD UART2 Receive Data DIG I Can be configured as G IO

4 UART2-TXD UART2 Transmit Data DIG O Can be configured as G IO

5 UART1-RTS UART1 Request to Send DIG I Can be configured as G IO

6 UART1-CTS UART1 Clear to Send DIG O Can be configured as G IO

7 UART1-RXD UART1 Receive Data DIG I Can be configured as G IO

8 UART1-TXD UART1 Transmit Data DIG O Can be configured as G IO

9 I2C-SDA I2C bus DATA DIG

I/O Can be configured as G IO

10 I2C-SCL I2C bus CLOCK DIG

I/O Can be configured as G IO

11 TMR1 Timer 1 I/O DIG I/O Can be configured as G IO

12 TMR0 Timer 0 I/O DIG I/O Can be configured as G IO

13 S I-SCK S I Clock DIG O

Can be configured as G IO

14 S I-MOSI S I Data Out DIG O

Can be configured as G IO

15 S I-MISO S I Data In DIG I

Can be configured as G IO

16 S I-SS S I Slave Select DIG O

Can be configured as G IO

17 GND Ground N/A N/A

18 KBI0 RTC clock out enable /

Keyboard interface pin 0

DIG O

19 RTC-FOUT 32768Hz RTC clock out DIG O

20 KBI6 Keyboard interface pin 6 DIG I/O Can be configured as G IO

21 KBI5 Keyboard interface pin 5 DIG I/O Can be configured as G IO

22 GND Ground N/A N/A

23 GND Ground N/A N/A

24 GND Ground N/A N/A

25 GND Ground N/A N/A

26 RTC-INT-B RTC wake-up interrupt /

Keyboard interface pin 7

DIG O

27 KBI1 Keyboard interface pin 1 DIG I/O Can be configured as G IO

28 KBI2 Keyboard interface pin 2 DIG I/O Can be configured as G IO

29 KBI3 Keyboard interface pin 3 DIG I/O Can be configured as G IO

30 KBI4 Keyboard interface pin 4 DIG I/O Can be configured as G IO

31 GND Ground N/A N/A

32 ADC3 ADC pin 3 Analog I Can be configured as G IO

33 ADC2 ADC pin 2 Analog I Can be configured as G IO

34 ADC1 ADC pin 1 Analog I Can be configured as G IO

User Manual

Proprietary & Confidential

Page 3

version 1.0

35 ADC0 ADC pin 0 Analog I Can be configured as G IO

36 ADC2-VREFH ADC2 reference, high pin Analog I Can be configured as G IO

37 ADC2-VREFL ADC2 reference, low pin Analog I Can be configured as G IO

38 GND Ground N/A N/A

39 VCC Supply voltage N/A N/A

40 GND Ground N/A N/A

41 RESET RESET pin DIG I

42 JTAG-RTCK JTAG Return Clock /

ADC pin 7

DIG O Can be configured as G IO

Can be configured as Analog In

43 JTAG-TDO JTAG Test Data Output DIG O Can be configured as G IO

44 JTAG-TDI JTAG Test Data Input DIG I Can be configured as G IO

45 JTAG-TCK JTAG Test Data Input DIG I Can be configured as G IO

46 JTAG-TMS JTAG Test Mode Select DIG I Can be configured as G IO

47 GND Ground N/A N/A

48 GND Ground N/A N/A

49 GND Ground N/A N/A

50 RF RF pin Analog I/O

52 GND Ground N/A N/A

Notes:

1.) Open collector pin if configured as I2C port

2.) Signal Dir valid if module is configured as S I Master

User Manual

Proprietary & Confidential

Page 4

version 1.0

Power is supplied to the modem through pins 38, 39 and 40.

Pin 39 must be supplied with 2.7 to 3.3 Volts and powers the digital and RF functional

entities of the modem. The modem has internal filtering circuitry to smooth out the

supply voltage but it has no onboard regulators.

All of the remaining pins of the modem are I/O lines of the processor, except for pin 50,

which is the RF I/O port.

The voltage on any of the I/O lines should never exceed VCC+0.3 V.

Pins 1 to 4 are attached to UART 2. Pins 5 to 8 are attached to UART1. If connecting to

the serial port of a PC, a level-shifting transceiver must be employed in order to provide

the appropriate voltage levels on the RX and TX lines.

3. Operation of the Nivis Radio Modem

Communication with the VN210 radio modem happens through serial port 1. The baud-

rate is set to be 115200, 8N1.

3.1. Getting started

Open a terminal software on a serial port with the above settings and connect to the RF

modem. Upon power up, the terminal will display a list of the available commands.

4. RF Exposure Limit Warning

To comply with FCC’s RF exposure limits for general population / uncontrolled

exposure, the antenna(s) used for this transmitter must be installed to provide a

separation distance of at least 20cm from all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter.

5. Compliance Statement (Part 15.19)

This Device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that

may cause undesired operation.

User Manual

Proprietary & Confidential

Page 5

version 1.0

6. OEM Responsibility

Only the approved antennas, which have been certified with this module should be

used. The approved antennas are:

ANT-2.4-CW-RCT-RP Linx Technologies (2.2 dBi)

ANT-N-5 Mini-Box (5.5 dBi)

FS1-F9915KB Yokogawa (2.0 dBi)

7. Warning (Part 15.21)

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Tabla de contenidos

Otros manuales de Módem de Nivis

Nivis

Nivis RF-P9-06-01-01 Manual de usuario

Nivis

Nivis RF-P9-06-01-01 Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario