Nivetec UNICONT Instrucciones de montaje

BKI15ATEX0013X/1



pdf4012m600p_06



1 / 24

2 / 24



pdf4012m0600p_06



BKI15ATEX0013X/1

APPROVALS:

INMETRO, Certificate No.: DNV 15.0064 X

BKI ATEX, Certificate No.: BKI15ATEX0013 X/1

BKI15ATEX0013X/1



pdf4012m0600p_06



3 / 24

CONTENTS

1.INTRODUCTION ...........................................................................................................................................................................................5

2.ORDER CODES............................................................................................................................................................................................5

3.TECHNICAL DATA....................................................................................................................................................................................... 6

3.1GENERAL DATA........................................................................................................................................................................................6

3.2ADDITIONAL DATA FOR EXPLOSION-PROOF CERTIFIED VERSIONS.................................................................................................................7

3.2.1.ATEX APPROVAL NO:BKI15ATEX0013 X/1 ......................................................................................................................................................... 7

3.2.2.INMETRO APPROVAL NO:DNV 15.0064 X........................................................................................................................................................... 8

3.3DIMENSIONS ............................................................................................................................................................................................9

3.4ACCESSORIES.......................................................................................................................................................................................... 9

3.5MAINTENANCE REPAIR,AND STORAGE CONDITIONS ....................................................................................................................................9

4.INSTALLATION AND ELECTRIC CONNECTION .....................................................................................................................................10

4.1WIRING.................................................................................................................................................................................................. 10

4.2SAFETY REGULATIONS FOR THE EX CERTIFIED UNITS...............................................................................................................................14

5.PUTTING INTO OPERATION, PROGRAMMING....................................................................................................................................... 15

5.1DEFAULT ...............................................................................................................................................................................................16

5.2DISPLAY OF THE SAP-202 AND KEYS OF THE UNIT................................................................................................................................... 16

5.3PROGRAMMING ......................................................................................................................................................................................17

5.3.1.STEPS OF PROGRAMMING ..................................................................................................................................................................................... 17

5.3.2.PARAMETERS –DESCRIPTION AND PROGRAMMING .................................................................................................................................................. 19

5.4ERROR INDICATIONS............................................................................................................................................................................... 24

5.4.1.VALID LED IS BLINKING AND A MESSAGE OF ERRXAPPEARS ON THE DISPLAY .......................................................................................................... 24

5.4.2.VALID LED AND THE DISPLAYED VALUE IS BLINKING ............................................................................................................................................... 24

5.4.3.ERROR INDICATION ON THE OUTPUT CURRENT (FOR 3-WIRE MODELS ONLY)............................................................................................................... 24

4 / 24



pdf4012m0600p_06



BKI15ATEX0013X/1



pdf4012m0600p_06



5 / 24

Thank you for choosing NIVELCO instrument

We are sure that you will be satisfied throughout its use!

1. INTRODUCTION

The UNICONT PDF-01 and PDF-01-6 / A / C Ex devices are 2-wire on-site indicators that can be inserted into a 4 – 20 mA current loop without the need for

additional power supply. Since the displayed value is proportional to the input, the units are suitable for indication of temperature, pressure, level, etc. values, the

information carried by the loop current. The customer can program the engineering units and the indication range.

The HART capable UNICONT PF-01-4 and PF-01-8 / B / D Ex 3-wire process indicators require additional power supply. Besides displaying the loop

current or the process values, these units convert input current to HART signals and so enable devices that have analogue outputs only to be integrated into

HART multidrop systems. The ratio between the input and output current can be programmed.

The intelligent electronics and HART communication enables versatile signal processing and remote programming. The software uses the Universal HART

commands No. 1 – 3, 6, 7, 11 – 18 and device specific commands No128-132, 135 and 139 of the HART Revision 5.

Robust enclosure makes applications under harsh conditions also possible. Explosion proof versions are available for hazardous environments.

2. ORDER CODES

UNICONT P F – 0 1 – *

FUNCTION CODE HOUSING CODE OUTPUT /EXCODE

With display D Aluminium 4 Display 2

Without display T Plastic 5 4 – 20 mA + HART 4

Stainless steel 6 Display / Ex ia 6

4 – 20 mA + HART / Ex ia 8

Not all combinations are possible!

Display / Ex d A

4 – 20 mA + HART / Ex d B

* The order code of an Ex version should end in “Ex” Display / Ex d+ia C

4 – 20 mA + HART / Ex d+ia D

The models with display outputs are 2-wire units.

6 / 24



pdf4012m0600p_06



BKI15ATEX0013X/1

3. TECHNICAL DATA

3.1 GENERAL DATA

TYPE PDF-01-2, PDF-401-A EX,

PDF-401-C EX

PDF-01-6 EX,PDF-601-A EX,

PDF-601-C EX

PF-01-4, PF-401-B Ex,

PF-401-D EX

PF-01-8 Ex, PF-601-B Ex,

PF-601-D EX

Powering 2-wire 3-wire

Input Current loop

Range 3.6 – 22 mA 0 – 22 mA

Display / indication 6-digit LCD, engineering units and bargraph

Range of displayed value -9999 – 29999

Engineering units (programmable) mA, ºC, ºF, %, m, cm, in, ft, l, m3, gal, ft3

Displayed process values (programmable) DIST (distance), LEV (level), VOL (volume / content)

Ambient temperature -40 ºC … +70 ºC [-40 °F … 158 °F], with display module: -25 ºC … +70 ºC [-13 °F … 158 °F]

Accuracy ±0.1% for displayed values over > 10 000

Temperature coefficient ±0.05% / 10 °C

Output ----

4 – 20 mA and / or HART for 4 – 20 mA current limit values: 3.9 – 20.5

terminal resistor for HART Rtmin = 250 

Error indication on the current output ---- Output = 3.8 or 22 mA

Power supply ---- Standard version: 10 V – 36 V Ex version: 10 V – 30 V

Load resistance ---- Rt(Us– 10 V) / 0.022A, where Ussupply voltage

Voltage drop < 1.6 V < 1 V

Overvoltage capability 140 mA

Damping 3 s, 5 s, 10 s or 20 s

Electric protection Class III

Ingress protection IP67

Electric connection Through M20x1.5 cable gland, shielded, twisted cable of 6 – 12 mm [0.24 in – 0.47 in], wire cross-section: max. 1.5 mm2[15 AWG]

Ex version: see additional data for Ex certified versions

Housing Paint coated aluminium PBT glass fibre reinforced or stainless steel (w. Nr 1.4571)

Mass Aluminium housing ~0.9 kg, stainless steel ~2.4 kg, plastic housing ~0.55 kg

BKI15ATEX0013X/1



pdf4012m0600p_06



7 / 24

3.2 ADDITIONAL DATA FOR EXPLOSION-PROOF CERTIFIED VERSIONS

3.2.1. ATEX APPROVAL NO:BKI15ATEX0013 X/1

Type PDF-501-6 EXPDF-401-6 EX

PDF-601-6 EX

PDF-401-A EX

PDF-601-A EX

PDF-401-C EX

PDF-601-C EX

Housing PBT glass fibre reinforced Paint coated aluminium

(EN AC-42000) or stainless steel Paint coated aluminium (EN AC-43100) or stainless steel

Ex protection Intrinsically safe Flame proof enclosure Flame proof, intrinsically safe

Ex marking II 1 G Ex ia IIC T6 Ga II 2 G Ex d IIB T6 Gb II 1 G Ex d+ia IIB T6 Ga

Intrinsically safety data Ui = 30 V Ii = 100 mA Pi = 0.7 W

(in case of IIB gas group: Ii = 140 mA / Pi = 1.1 W)

Ci ≈0 nF Li < 200 H Ui = 30 V Ii = 140 mA Pi = 1.1 W

Ci ≈0 nF Li < 200 H

Electrical connection Plastic cable gland M20x1.5 for cable diameter 6 – 12 mm Ex d cable gland M20x1.5 for cable diameter: 8 – 12 mm

Shielded twisted pair cable, wire-end cross-section: 0.25 – 1.5 mm2

Ambient temperature -25 ºC … +70 ºC

Type PF-501-8 EXPF-401-8 EX

PF-601-8 EX

PF-401-B EX

PF-601-B EX

PF-401-D EX

PF-601-D EX

Housing PBT glass fibre reinforced Paint coated aluminium

(EN AC-42000) or stainless steel Paint coated aluminium (EN AC-43100) or stainless steel

Ex protection Intrinsically safe Flame proof enclosure Flame proof, intrinsically safe

Ex marking II 1 G Ex ia IIB T6 Ga II 2 G Ex d IIB T6 Gb II 1 G Ex d+ia IIB T6 Ga

Intrinsically safety data Ui = 30 V Ii = 140 mA Pi = 1.1 W

Ci < 20 nF Li < 200 H Ui = 30 V Ii = 140 mA Pi = 1.1 W

Ci < 20 nF Li <200 H

Electrical connection Plastic cable gland M20x1.5 for cable diameter 6 – 12 mm Ex d cable gland M20x1.5 for cable diameter: 8 – 12 mm

Shielded twisted pair cable, wire-end cross-section: 0.25 – 1.5 mm2

Ambient temperature -40 ºC … +70 ºC, with display module: -25 ºC … +70 ºC

8 / 24



pdf4012m0600p_06



BKI15ATEX0013X/1

3.2.2. INMETRO APPROVAL NO:DNV 15.0064 X

Type PDF-401-6 EX

PDF-501-6 EX

PF-401-8 EX

PF-501-8 EXPDF-401-C EXPF-401-D EX

Housing PBT glass fibre reinforced or paint coated aluminium Paint coated aluminium

Ex protection Intrinsically safe Flame proof enclosure and intrinsically safe

Ex marking Ex ia IIC Ex ia IIB Ex d+ia IIB

Intrinsically safety data Ui = 30 V Ii = 100 mA Pi = 0.7 W

Ci ≈0 nF Li < 200 H Ui = 30 V Ii=140 mA / Pi = 1.1 W)

Ci ≈20 nF Li < 200 H Ui = 30 V Ii = 140 mA Pi = 1.1 W

Ci ≈0 nF Li < 200 H Ui = 30 V Ii = 140 mA Pi = 1.1 W

Ci ≈20 nF Li < 200 H

Type PDF-401-6 EX

PDF-501-6 EX

PDF-401-A EX

PDF-401-C EX

PF-401-8 EX

PF-501-8 EX

PF-401-B EX

PF-401-D EX

Ambient temperature -25 ºC … +70 ºC Without display module: -40 ºC … +70 ºC, with display module: -25 ºC … +70 ºC

BKI15ATEX0013X/1



pdf4012m0600p_06



9 / 24

3.3 DIMENSIONS

Aluminium or plastic housing Stainless steel housing

102

51.0

4.2

108.0

120.0

4.0

~113 130

117

~145

~100

5.4

5.5

Type A

Standard, Ex ia ~137 mm

Ex d, Ex d+ia ~145 mm

3.4 ACCESSORIES

Standard, Ex ia: Ex d, Ex d+ia:

– Installation and programming manual

– Warranty Card

– Declaration of Conformity

– 2 cable glands

– Sticker set of engineering units – Installation and programming manual

– Warranty Card

– Declaration of Conformity

– Sticker set of engineering units

– CDROM with EView2 software

for HART devices

3.5 MAINTENANCE REPAIR,AND STORAGE CONDITIONS

UNICONT PDF units do not require maintenance on a regular basis. Repair under or after the guarantee period should only be carried out by NIVELCO.

Unused devices must be stored within the ambient temperature range specified in the technical data, with a maximum of 98% relative humidity.

10 / 24



pdf4012m0600p_06



BKI15ATEX0013X/1

4. INSTALLATION AND ELECTRIC CONNECTION

The devices are suitable for working in closed area or they can be used in open-air applications. When choosing the installation place please ensure proper

space for the mounting, programming and checking the display. Mounting the units on the wall or to a support can be done with using 2 pcs of M4 nuts. To avoid

overheating the instrument should be protected against direct sunshine.

4.1 WIRING

 2-wire indicators are used in 4 – 20 mA current loops. They do not require external power supply.

 3-wire devices are powered with 10 V – 36 V DC (Ex type devices: 10 V – 30 V DC) through the output.

 Make sure, that current values on the internal terminals should not exceed overload capability limits.

 Wiring should be done with shielded cable, specified under ‘Technical Data’ table.

 Devices should be grounded by using their grounding screws.

 The screw terminals can be accessed after removal of the housing cover and the display module.

 After wiring and programming the cover should be screwed to tightness of the sealing.

The housing cover of the flameproof device is allowed to remove only when the unit is de-energized!

The housing cover can be removed after unscrew the M2 size hex socket set screw

or after dismounting the safety locking bolt by unscrew the M4 size hex socket set screws.

The instrument may be damaged by electrostatic discharge (ESD) via its terminal, thus apply the precautions commonly used to avoid

electrostatic discharge e.g. by touching a properly grounded point before removing the cover of the enclosure.

A possible electrostatic discharge can cause damage for the instrument. Do not touch the internal terminals!

After wiring and programming the housing cover should be closed properly and the hex socket set screw or the safety locking bolt should be

tightened! The sealing ring must be replaced if damaged, otherwise the IP class of the device can be jeopardized.

Tabla de contenidos

Otros manuales de Instrumento de medición de Nivetec

Nivetec

Nivetec PCM F Manual de usuario

Nivetec

Nivetec Micronics U1000-HM Manual de usuario

Nivetec

Nivetec AquaSensors AV88 Manual de usuario

Nivetec

Nivetec U1000MKII-HM Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario