Niveo Professional NWA220 Manual de usuario
All rights reserved Niveo International BV 2020
User Manual of 11 ac 1200Mbps Outdoor CPE NWA220
This is the user manual of 11ac 1200Mbps Outdoor CPE, which will approximate guide
you how to set and apply the NWA 200 Outdoor CPE
More information:
WWW.NIVEOPROFESSIONAL.COM
INFO@NIVEOPROFESSIONAL.COM
All rights reserved Niveo International BV 2020
1st Hardware and Operation mode instruction
WAN: Gigabit WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under
Outdoor CPE and WiFi Repeater operation mode.
Power Supply:
Powered by PoE Switch
The connection diagram shows as P2, Internet cable from PoE Switch to Outdoor CPE’s WAN
Port, then PC access into Outdoor CPE wired/wireless.
Pls note, the outdoor CPE support IEEE 802.3at PoE, the switch should comply with IEEE 802.3at
PoE standard.
Connect Outdoor CPE with PC:
User can connect the PC with Outdoor CPE by Wireless SSID and LAN cable:
The diagram of wireless connection showed as follow:
Pls note: the default SSID is WirelessAP2.4G/5.8G, SSID’s password is 66666666
All rights reserved Niveo International BV 2020
2nd: Login
Default IP: 192.168.2.200
Username: admin
Password: admin
1）Connect the Outdoor CPE with computer
2）Configure the PC’s local connection IP address as 192.168.2.X (X is number from 2 to 254),
subnet mask is 255.255.255.0.
3) Input 192.168.2.200 into IE browser, then pop up the login page, the default login user name:
Admin, Passwords: admin.
3rd: WEB GUI interface Setting
1 Status
After login, then P7 Device Status will be showed:
Device Status
In this Outdoor CPE, the default operation mode is AP mode.
Then in 2.4G Wireless Setting, GUI configuration page showed as below:
User can configure the SSID, password, band width, channel here, then Apply to finish.
All rights reserved Niveo International BV 2020
2.4G Wireless setting
5.8G Wireless Setting GUI configuration setting showed as:
5.8G Wireless Setting
All rights reserved Niveo International BV 2020
LAN Setting to configure the DHCP or Fix IP
LAN Setting
AP location setting: can mark where the AP set up, and AP name as:
AP Position setting
All rights reserved Niveo International BV 2020
2) Wizard Configuration:
Click Wizard in Status page, will pop up following page to configure the operation mode:
There are four operation mode of this ceiling Outdoor CPE, and there are explanation for each
operation mode for better application.
Operation mode
1. Gateway Mode:
Click Gateway mode, will pop up following pictures:
Pls choose the right WAN setting mode, then click next to continue.
All rights reserved Niveo International BV 2020
WAN setting in Gateway Mode
Wireless Setting in Gateway Mode
All rights reserved Niveo International BV 2020
When click Next, then will complete the Gateway mode setting and show following picture:
Complete the setting in Gateway Mode
When return to Status, the page showed as follow:
Status in Gateway Mode
All rights reserved Niveo International BV 2020
2. WiFi Repeater mode
Click WiFi Repeater operation mode in Wizard, then following page will pop up, and choose the
right SSID to bridge, then next.
Repeater Mode
After click Next button, then should configure the wireless setting as follow, then click Next to
finish:
P17 Wireless Setting in Repeater Mode
All rights reserved Niveo International BV 2020
Click Return button, will back to Status, show Repeater mode data, show fail or success, and
user can configure this data in this page if required.
Status in Repeater Mode
Pls note, when click wireless relay setting, following page will pop up, you can make change from
here easy:
Wireless Relay Setting
Otros manuales para NWA220
2
Otros manuales de Punto de acceso inalámbrico de Niveo Professional
Niveo Professional
Niveo Professional NWA220 Manual de usuario
Niveo Professional
Niveo Professional NWA200 Manual de usuario
Niveo Professional
Niveo Professional NWA220 Manual de usuario
Niveo Professional
Niveo Professional NRS-AP10 Manual de usuario
Niveo Professional
Niveo Professional NWA 100 Manual de usuario
