NiteRider Evolution Smart Manual de usuario

Halogen

NiMH

USER GUIDE

Evolution Smart

NiteRider and Evolution Smart are trademarks of NiteRider, Inc.

All other trademarks are the property of their respective owners.

The information in this document is subject to change without notice.

DISCOVER THE NIGHT!

Thank you for choosing the Evolution Smart™ system from

NiteRider, the innovator in technical lighting systems. The

Evolution Smart incorporates fast charging and NiteRider’s

patented “smart” battery and lamp technologies that extend

system life. The Evolution Smart system includes:

• Halogen lamp with four brightness levels and three ﬂash

modes for safety

• Compact, lightweight nickel metal hydride (NiMH) battery

• 2.5-hour fast charger

• Fuel (battery) gauge

• Frame and helmet mounting

To get the most from your NiteRider light, we urge you to

familiarize yourself with the following safety and operation

instructions.

PROTECTING

YOUR INVESTMENT

When not in use, always disconnect the headlamp from the

battery. To unplug, grasp the connector, not the cable.

Properly charge your battery to maximize its lifespan

(see “Battery Charging and Care” on page 12). To avoid

damaging your system, only charge your NiteRider battery

with the appropriate NiteRider charger.

While Evolution Smart will perform in wet weather conditions,

submerging it in water will damage the system. If you need a

submersible light, NiteRider manufactures industrial-grade

dive light systems. For information, contact NiteRider Dive

Lights at 858.268.3850 or visit www.niteriderdive.com.

RIDING AT NIGHT

While the Evolution Smart will improve your control and

enjoyment of night riding, please remember that cycling at

night is an inherently dangerous activity. In addition to using

your lighting system properly and riding with extreme caution,

NiteRider urges you to:

• never ride alone

• always let someone know where you are going

• wear a helmet and reﬂective clothing

• carry an auxiliary light and emergency supplies.

NiteRider, Inc.

8205 Ronson Road, Suite E

San Diego, CA 92111 USA

800.466.8366

www.niterider.com

SUPPORT

If you experience difﬁculties during product installation or

operation, NiteRider provides free telephone support on

weekdays from 8:00 AM to 4:30 PM (Paciﬁc Time) at

800.466.8366, ext. 4. You may also e-mail us at

support@niterider.com.

WARRANTY

NiteRider stands behind its products with the following

warranties:

• Lifetime warranty on all mechanical components

• 1 year on cables and connectors, electronic components,

and printed circuit boards

• 180 days on rechargeable batteries and fast chargers

• 60 days on halogen bulbs

To repair or replace your product while under warranty, return

it (postage prepaid and insured with original sales receipt) to

the address below. Out-of-warranty repair service is also

available. For complete warranty information, please visit our

website.

TABLE OF CONTENTS

Parts List and Identification

. . . . . . . . . . . . . . . . . . . . . . 4

Quick Start

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mounting the Headlamp

. . . . . . . . . . . . . . . . . . . . . . . . . 6

Universal Handlebar Mount . . . . . . . . . . . . . . . . . . . . . . 6

Helmet Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Inserting the Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting the Battery

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Frame Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Pocket or Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Flash and Walking Modes . . . . . . . . . . . . . . . . . . . . . . 10

Fuel Gauge and Automatic Shut Off. . . . . . . . . . . . . . 11

Battery Charging and Care

. . . . . . . . . . . . . . . . . . . . . 12

Using the 2.5-hour Fast Charger . . . . . . . . . . . . . . . . . 12

Battery Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Smart Battery Protection . . . . . . . . . . . . . . . . . . . . . . . . 12

Storage . . . . . . . . . . . . . . . . . . . . . . . . Inside Back Cover

Run Times

. . . . . . . . . . . . . . . . . . . . . . . . Inside Back Cover

PARTS LIST

AND IDENTIFICATION

Please verify the contents of your Evolution Smart system:

A. 15 Watt-6 Volt halogen headlamp

B. 4.5 Ah-6 Volt NiMH battery (pocket/frame mount)

C. Charger power cord

D. Universal handlebar mount

E. 2.5-hour fast charger

F. Helmet mount

G. 36” helmet cord

H. Velcro cable tie

QUICK START

1. Fully charge the battery before the ﬁrst use. See “Using the

2.5-hour Fast Charger” on page 12.

2. To mount the headlamp and battery, see “Mounting the

Headlamp” on page 6 and “Mounting the Battery” on

page 8.

3. Connect the battery to the headlamp.

4. To turn the light on for normal operation, press and hold the

headlamp power button for one second. Cycle through the

three brightness levels by pressing and releasing the

power button.

5. To access the ﬂash and walking modes, see “Flash and

Walking Modes” on page 9.

6. To turn the system off, press and hold the power button for

one second.

MOUNTING THE HEADLAMP

The Evolution Smart headlamp can be mounted to the

handlebar or a helmet.

Universal Handlebar Mount

The Universal Handlebar Mount (UHM) is designed to ﬁt on

virtually any handlebar. Included with the mount is a 2.5-mm

Allen wrench, a pair of black rubber bumpers already in

place, and a thin rubber shim to customize the ﬁt on large

handlebars up to 32 mm in diameter.

Turn the knob counter-clockwise, allowing the hinge to swing

open. Place the mount on the handlebar on the left side the

stem, orienting the rectangular notch in the slider clip to the

rear. Swing the hinge down to make contact with the

handlebar. Swing the hex bolt up, seating the knob into its

recess. Turn the knob clockwise to tighten and secure the

mount to the handlebar.

The UHM can be adjusted to accommodate any handlebar

angle. By loosening the 2.5 x 30 mm Allen screw, you can

move the swing arm back and forth to straighten the

headlamp. Tighten the 2.5 x 30 mm screw after the

adjustment.

NOTCH

SWING ARM

2.5 x 30 MM

SCREW

HINGE

KNOB

HEX BOLT

SLIDER CLIP

2.5 x 12 MM

SCREW

To pivot the headlamp, loosen the 2.5 x 12 mm screw located

under the slider clip and swing arm and rotate the headlamp

to the desired position. Make this adjustment before

tightening the 2.5 x 30 mm screw.

Helmet Mount

1. Unclamp the straps on each

side of the helmet mount and

pull them free.

2. Position the plastic mounting

plate as close to the centerline

of the helmet as possible,

orienting the parallel grooves on

the slider clip to the rear.

3. Feed each strap into and out of

two helmet vents, circling each

strap back to the upper edge of

the corresponding clamp.

4. Fasten the straps by inserting

them into the clamps.

Inserting the Headlamp into

the Handlebar or Helmet Mount

Insert the headlamp mount into the handlebar or helmet

mount slider clip from the rear of the slider clip forward.

Gently rocking the lamp as you slide it may help. Do not push

the release lever when inserting the headlamp into the slider

clip; let the lamp snap into place by itself.

To remove the headlamp, push the release lever and slide the

lamp backward.

Note

: After mounting the headlamp, adjust the headlamp so

it illuminates the road properly without distracting oncoming

riders.

MOUNTING THE BATTERY

The battery can be mounted to the bike frame or placed in a

jersey pocket, hydration pack, or fanny pack.

Warning

: For safety reasons, a cyclist should never be

tethered to the bike. If the headlamp is mounted to the

helmet, do not mount the battery to the frame. Conversely, if

the headlamp is mounted to the handlebar, do not place the

battery in a pocket or pack.

Frame Mount

1. Thread the wide Velcro tie

through the slots on the top of

the battery clip.

2. Attach the concave surface of

the battery to a safe,

convenient location on the

frame (typically under the top

or down tube), placing the

Velcro strap over the tube but

under any shift or brake cables.

3. Secure the handlebar cord to

the frame using the thin Velcro

tie. Make sure the cord does

not interfere with any moving

parts.

Tabla de contenidos

Otros manuales de Accesorios para bicicletas de NiteRider

NiteRider

NiteRider MiNewt Mini 300-USB Manual de usuario

NiteRider

NiteRider Pro Series Manual de usuario

NiteRider

NiteRider Lumina Micro 220 Manual de usuario

NiteRider

NiteRider RoadRat Manual de usuario

NiteRider

NiteRider PRO 1400 RACE Manual de usuario

NiteRider

NiteRider FireStorm Manual de usuario

NiteRider

NiteRider LUMINA MAX 2500 Manual de usuario

NiteRider

NiteRider MiNewt.200 Manual de usuario

NiteRider

NiteRider PRO 1800 Race Manual de usuario

NiteRider

NiteRider PRO 2800 ENDURO REMOTE Manual de usuario

NiteRider

NiteRider PRO 3600 DIY REMOTE Manual de usuario

NiteRider

NiteRider MiNewt Dual Manual de usuario

NiteRider

NiteRider PRO 2800 Manual de usuario

NiteRider

NiteRider Evolution Manual de usuario

NiteRider

NiteRider PRO Series Manual de usuario

NiteRider

NiteRider Solas 250 Manual de usuario

NiteRider

NiteRider PRO 2200 RACE Manual de usuario

Manuales populares de Accesorios para bicicletas de otras marcas

Sigma

Sigma BC 16.16 Manual de usuario

Playcore

Playcore Dero Setbacks Manual de usuario

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manual de usuario

Cateye

Cateye RAPID X2 Manual de usuario

buratti meccanica

buratti meccanica Clorofilla Trail Manual de usuario

Shimano

Shimano SG-8R20 Instrucciones de funcionamiento

BOB

BOB YAK Manual de usuario

APLIC

APLIC 303303/20190717TW012 Manual de usuario

SRAM

SRAM AXS BlipBox Manual de usuario

Garmin

Garmin EDGE 500 Manual de usuario

Shimano

Shimano FD-RX810 Manual de usuario

Cateye

Cateye V2C - Manual de instrucciones

KMART

KMART 43115907 Manual de usuario

SIGMA SPORT

SIGMA SPORT Buster 2000 Manual de usuario

NVO Components

NVO Components STEM Manual de usuario

DAXYS

DAXYS BP188 Manual de usuario

XLC

XLC BV-W17 Manual de usuario

Deda Elementi

Deda Elementi SUPERBOX Manual de usuario