Nintendo GameCube Modem Adapter Manual de lista de piezas

Nintendo GameCube Console Memory Battery Replacement Guide Page 1of 10

Nintendo GameCube Console Memory Battery Replacement Guide

Thank you for your purchase of a Nintendo GameCube console memory battery from Mortoff Games.

We appreciate your business and hope to serve you again in the future. This guide is intended to take

you through the steps involved in replacing your console’s memory battery. If at any time you have

questions please feel free to contact us at customerservice@mortoffgames.com

Things you will need

A 4.5mm security screw bit that is at least

A Philips head screw driver

A soldering iron

Soldering braid

Solder

Clean work area where small screws will not get lost

About 15 minutes of free time

Warning

When dealing with solder it is important to realize that when vaporizing the material you are exposing

yourself to gaseous forms of the material the solder is composed to. Some of these are harmful to living

creatures. We recommend that you use a gas hood for all soldering and wear proper eye and hand

protection at all time. If a gas hood is not available please solder in a well-ventilated area.

Nintendo GameCube Console Memory Battery Replacement Guide Page 2of 10

Soldering Techniques:

In order to solder and unsolder correctly you will need a soldering iron, solder and soldering braid. Once

you have these items you can precede forward. For the duration of this project it is not recommend that

you use a cold heat or any other instantaneous heating soldering gun, since these guns use an electrical

current to melt the solder. Passing a strong electrical current through your games is not recommended

and as such should be avoided. We recommend that you use a typical soldering gun, the type that you

have to plug in and wait to heat up. In addition it is recommended that you set your soldering iron to

30watts for the duration of this project.

Unsoldering-

Correctly unsoldering a joint is rather easy once you get the hang of it. In order to unsolder a joint place

soldering braid over the solder you wish to remove and then place the soldering iron over the soldering

braid. The soldering iron will heat the braid and in turn the solder will liquefy, which will be sucked up by

the braid. Please see picture one

Picture Introduction

Although it might take a little while to completely remove all of the solder, patience and persistence will

pay off in this case. Every 10-15 seconds remove the soldering braid and check to see if the solder have

been fully removed. Take note to notice that the solder is accumulating on the soldering braid as it is

This is the inside of a Super Nintendo game cartridge.

The

soldering

braid is

placed over

the solder

you want to

remove

The soldering iron is

placed over the

soldering braid

Nintendo GameCube Console Memory Battery Replacement Guide Page 3of 10

being sucked up you should periodically keep cutting off the used portion of the soldering braid and use

fresh braid as needed.

Soldering-

Now that the solder has been removed you can now remove the object that the solder was holding in

place and you are now ready to solder something new into place.

The two most important things to keep in mind are:

1) Never allow patches of solder to overlap or touch, doing so creates a short, thereby rendering the

circuit inoperable.

2) Make sure to use enough solder to securely attach whatever it is you are soldering, do not be afraid

to test the joint out.

Keeping these items in mind lets continue with our demonstration. To apply the solder take it and place

it over the soldering joint and then lightly place the soldering iron over the solder. This is just like

unsoldering, although this time you are soldering and not unsoldering. This part is a little tricky when

you first start and is hard to describe with words alone. It is recommended that you test out melting

solder first to get an idea of how it behaves.

One ideal exercise you might want to try is to attempt to solder together two pieces of wire. Take two

pieces of wire, strip the ends, twist the ends together and then practice applying solder over this twisted

joint. During the course of this project if you run into trouble remember you can always back track and

remove the solder and try again, using the soldering braid. Soldering braid and solder are very cheap

and as such are worth playing around with to get comfortable with before you go ahead and try to

solder in a replacement battery. Now that we have covered the basics of soldering and unsoldering, let’s

get started with the replacement of that battery.

Nintendo GameCube Console Memory Battery Replacement Guide Page 4of 10

Step One

First please flip your Nintendo GameCube system over and locate the four 4.5mm security screw bits

that are holding the casing together as seen in picture one below.

Picture One: Bottom side of the Nintendo GameCube system

Once the screws have been removed please separate the two halves of the Nintendo GameCube system

and proceed to step two.

4.5mm security screw bits

Nintendo GameCube Console Memory Battery Replacement Guide Page 5of 10

Step Two

Now that the system it should look like picture two below. You might notice that there is a great deal of

dust in the system at this time. Since you are already here now is a great opportunity to use some duster

spray to clean out the dust. Excessive dust in your system can lead to overheating because it impairs

ventilation.

Picture Two: Inside of the Nintendo GameCube system

In picture two above the CR2032 coin cell battery is indicated in picture two above. Simply take the

controller port assembly and lift it out of the system. The controller port is attached by a small ribbon

cable to the rest of the system. Simply pull it upwards to release it.

Once the controller port has been separated from the rest of the system please proceed to step three.

CR2032 Battery

Nintendo GameCube Console Memory Battery Replacement Guide Page 6of 10

Step Three

Now that the controller port has been detached you will notice two Philips screws on the controller port

circuit board as noted in picture three below. Please unscrew them to release the plastic faceplate from

the circuit board.

Picture Three: Controller port circuit board Philips head screws

Once the screws are removed please remove the plastic faceplate and proceed to step four.

Philips screws

Nintendo GameCube Console Memory Battery Replacement Guide Page 7of 10

Step Four

Now that the faceplate is off the battery should be exposed as seen in picture four below. Now it is time

to remove the battery using your soldering skills learned previously.

Picture Four: CR2032 Battery

Once the battery has been removed please proceed to step five.

Positive

Terminal

Negative

Terminal

Nintendo GameCube Console Memory Battery Replacement Guide Page 8of 10

Step Five

We recommend that you insert the tabs into the holes and then bend the tabs as seen in picture five

below. This will not only keep the battery in place, although will make the solder joint stronger. Please

make sure that you are inserting the positive battery terminal into the positive terminal on the circuit

board and vice versa. The board is marked below and in picture four previously.

Picture Five: Bending the pins on the CR2032 battery

Now that the battery is ready to solder on using your skills learned earlier please solder on the battery

and proceed to step six.

Positive

Terminal

Negative

Terminal

Nintendo GameCube Console Memory Battery Replacement Guide Page 9of 10

Step Six

Now that the terminals are soldered on your circuit board should look something like picture six below.

Picture Six: Proper terminal soldering

Notice how the terminals have enough solder on them to make a firm connection, although not so much

that it bridges to solder joints? This is what you are aiming for. Once finished please reassemble your

system and try out your system. You will have to re-enter the date and time on last time, although the

battery should last for many years to come.

If your system is not operating like it should after you reassemble the system please see our

troubleshooting section at the end of this guide.

Nintendo GameCube Console Memory Battery Replacement Guide Page 10 of 10

Troubleshooting Guide

We are sorry to hear that everything didn’t go as planned; although this section of the guide is intended

to help you troubleshoot and hopefully repair the problem you are experiencing. If you have other

questions please email us at customerservice@mortoffgames.com

1) My controllers do not work

a. Did you plug the controller assembly back into the system during reassembly?

2) I still have to reenter the date and time every time I start the system

a. Did you make sure to arrange the battery terminal to match the positive to the positive

and the negative to the negative?

Otros manuales para GameCube Modem Adapter

Otros manuales de consola de juegos de Nintendo

Nintendo

Nintendo N64 - 64 Game Console Manual de usuario

Nintendo

Nintendo 3DS XL Manual de usuario

Nintendo

Nintendo Switch Manual de usuario

Nintendo

Nintendo Nintendo Switch Joy-Con HAC 001 Guía de instalación y uso

Nintendo

Nintendo Gameboy Advance Manual de usuario

Nintendo

Nintendo RVL-001 - Wii Sports Pack Game Console Manual de usuario

Nintendo

Nintendo 2DS Manual de usuario

Nintendo

Nintendo Switch Starlight Manual de usuario

Nintendo

Nintendo 3DS Manual de usuario

Nintendo

Nintendo Switch Manual de funcionamiento

Nintendo

Nintendo Wii U Manual de instrucciones

Nintendo

Nintendo TETRIS AXIS Manual de usuario

Nintendo

Nintendo PCHU-MG5 Manual de usuario

Nintendo

Nintendo Wii Manual de usuario

Nintendo

Nintendo 3DS Manual de usuario

Nintendo

Nintendo Wii U Manual de usuario

Nintendo

Nintendo Game Boy Link Cable Manual del propietario

Nintendo

Nintendo DS Lite Manual de usuario

Nintendo

Nintendo New 2DS XL Manual de usuario

Nintendo

Nintendo RHYTHM HEAVEN Manual de usuario

Nintendo

Nintendo Wii U Deluxe Set Guía de instalación

Nintendo

Nintendo 3DS XL Manual de usuario

Nintendo

Nintendo Switch Guía de inicio rápido

Nintendo

Nintendo Wii U Deluxe Set Manual de usuario

Manuales populares de consola de juegos de otras marcas

Atari

Atari 2600 Manual de usuario

PLAYNETIC

PLAYNETIC GameNetic Manual de usuario

Sony

Sony SCPH-50008 Manual de usuario

Saitek

Saitek Alchemist Plus Manual de usuario

Sears

Sears Tele-Games 637.99743 Manual de usuario

AYANEO

AYANEO 2 Manual de usuario

Sony

Sony PlayStation 3 (Uncharted: Drake's Fortune Limited Edition... Manual de usuario

Mattel

Mattel My Meebas N2214 Manual de usuario

Entex

Entex PacMan2 Manual de usuario

Sega

Sega 32X Manual de usuario

Saitek

Saitek Cougar Manual de usuario

View-Master

View-Master Interactive Vision Diagrama de cableado

Sony

Sony SCPH-35003 GT Manual de usuario

Sony

Sony PSP go Manual de usuario

Sony

Sony PSVITA Manual de usuario

Excalibur

Excalibur ABC Wide 333 Manual de usuario

Microsoft

Microsoft XBOX Manual del propietario

LEXIBOOK

LEXIBOOK JL2700 Manual de usuario