Nilfisk-ALTO ATTIX 30 M Instrucciones de funcionamiento

Repair manual

ATTIX BASIC-ATTIX 30- 01 PC

ATTIX 30-11 PC-ATTIX 30-21 PC

ATTIX 40-01 PC INOX-ATTIX 40-21 PC INOX

ATTIX 50- 01 PC- ATTIX 50-21 PC

Wet & Dry Vacuums

Nilfisk

ALTO Index

A. Saftey Issues 3-4

B. Technical data 5

C. Construction 6-8

D. Function 9-10

E. Trouble shooting 11-15

F. Spare parts 16-20

G. Diagram 21-22

H. Tools 23

Nilfisk

ALTO A

Preface

In this manual you will find

the essentials you need

to know when repairing

wet and dry cleaners of

the Attix series.

When carrying out repairs,

make sure you have a suitable

workbench or the like with the

necessary power supply

available.

If you determine an error

in operation, be sure to

refer the customer to the

user manual.

A fault in the equipment

can have a number of causes.

Chapter E Troubleshooting

will help you here.

Use the illustrated spare

parts lists for your repairs.

These show you the location

of the individual parts and the

sequence in which they are

assembled.

Read the technical informa-

tion sheets. These will tell you

about any technical modifica-

tions made after publication of

this repair manual.

Technical information

sheets are a supplement

to the spare parts list until

a follow-on publication.

Repair manuals and technical

information sheets

should be available at the

site where repairs are carried

out. Further repair

manuals of the Attix series

may be necessary for

repairs to the equipment.

It is not permitted to give

them to third parties.

Use original Nilfisk

ALTO spare parts only!

Safety instructions marked

with this symbol in

this manual must be ob-

served

to prevent danger to per-

sons.

This symbol is used to

mark safety instructions

that must be observed to

prevent damage to the

equipment and degradation

of performance.

This symbol indicates tips

and instructions to simplify

work and to ensure safe

operation

Symbols used to mark

instructions

Nilfisk

ALTO A

Safety Issues.

Observe national safety

directives and regulations

for the electrical engineer-

ing

trade, in particular:

IEC 60335-2-69

EN 60335-2-69

DIN VDE 105 part 1:

operation of electrical

power installations.

DIN VDE 0701/0702:

repair, modification and

testing of electrical installa-

tions.

Before starting the equip-

ment,

be sure to read the

accompanying service

manual, and keep it close

as ready reference.

The equipment should

only be used by persons

who have been instructed

in its use and are author-

ized to do so.

Repairs should only be

made by someone who

has received proper

instructions for the job

or who is a qualified elec-

trician.

For your own safety.

ESD (electrostatic discharge)

Observe the following ESD precautions before any

repair of or near electronic parts:

• Touch the protective conductor to discharge your own body.

• Possibly wear an anti-static wrist strap.

• Use a conducting floor or tabletop.

• Never touch a circuit board or electronic components,

always hold them by the plastic or insulation.

• Transport electronic parts in conductive packaging (e.g. special ESD packages).

Nilfisk

ALTO B

Technical Data.

Attix 30-01 Ba-

sic Attix 30-01

PC Attix 30-11

PC Attix 30-21

PC Attix 40-01

PC Attix 40-21

PC Attix 50-01

PC Attix 50-21

National Variants EU

Voltage V230

Frequency Hz 50/60

Fusing A16

Power consumption PIEC W1200

Connected load for applica-

tions socket W2400 2400 2400 2400

Total connected load W1200 3600 1200 3600 1200 3600

Power cord lenght m7,5

Power cord type H05RR-F2X0,75X8,05 H05RR-F 3G1,5X8,2 EU

Protection class II I

Protection category IPX4

RFI suppression EN 55014-1

Air volume flow (max) l/min 3700

Static wate lift (max) mbar 250

Sound pressure level at 1m,

EN 60704-1 62

Noise level in working dis-

tance dB(A) 59

Nilfisk

ALTO C

Construction.

2 3

1.Push and clean bottom.

2.Outlet socket.

3.On / Of switch

Attix 30-01 Basic

Attix 30-01 PC

Attix 40-01 PC

Attix 50-01 PC

Attix 30-11 PC

Attix 30-21 PC

Attix 40-21 PC

Attix 50-21 PC

Attix 50 Attix 30

Attix 40 Inox

Nilfisk

ALTO C

Construction.

Connection load for applications

Socket. Air guide.

Electronic board. Suction motor

Air flap. Motor gasket.

Nilfisk

ALTO C

Construction.

Attix 30-01 Basic - Attix 30-01 PC -Attix 40-01 PC - Attix 50-01 PC

With soft start.

Electrical components.

Attix 30-21 PC - Attix 40-21 PC- Attix 50-21 PC

With soft start and aut. start / stop for tools.

Nilfisk

ALTO D

Function.

Vacuuming

Cleaning the filter push &

FC-button pressedFC-button pressed

Fitting

closed

Fitting

closed

Flap

Filter

Turbine

Fitting

Container

FC-button

3 1

By sealing the suction opening (1) a

high negative pressure is generated

inside the dirt tank when the motor is

running which keeps this under ten-

sion.

By actuating the cleaning button (2) on

the suction head, an air flap is opened

in the carrier plate, which allows air to

flow into the inside of the filter (3). The

air flows through the filter fleece from

the inside to the outside.

The negative pressure inside the dirt

tank is reduced very quickly and the

tank wall relieved of pressure.

Cleaning is always carried out for a

short time, mainly by relieving the tank

wall in short bursts.

The dirt adhered to the filter is blown

and shaken off, causing it to fall back

into the tank.

To optimise the cleaning effect, we

recommend that you actuate the

cleaning button briefly a number of

times.

--Several functions are integrated on this printed circuit board.

- Main switch with positions

-“Man-0-Auto”

- Radio interference suppression

- Speed control

- Soft start

- Automatic starter for electric tools

Nilfisk

ALTO D

Function.

Technical description of automatic starter with speed control

Soft start:

In cleaners fitted with the electronics men-

tioned above, the motor is always started with

a soft start.

Advantages:

The gentle start up of the motor re-

duces the starting currents so that

the mains fuse does not blow during

start up. In

addition, soft start greatly reduces the

load on the turbine

When it starts up. This results in a

considerable increase in the service

life of the turbine.

Main switch:

Two modes can be selected with

the main switch.

Man: The turbine starts immedi-

ately.

Auto: The turbine waits for an elec-

tric tool to be switched on at the

socket.

Speed control:

Speed control has been integrated into

the manual and automatic modes.

Settings on the switch range are possible

from 45° to 135°.

Advantages:

- Optimum adjustment of the

suction power to suit the

application.

- Increase in the ser vice

life of the turbine

- Reduction in noise emis-

sion

- Energy savings

Automatic starter

Work with an electric tool (grinder, etc.) can be opti-

mised by using the automatic starter.

The main switch is set to the “AUTO” position and

the electric tool connected to the socket of the

cleaner. The suction motor is

switched off. When the electric tool is now switched

on, the automatic starter detects.

The flow through the connected machine and

switches the suction motor on.

When work with the electric tool is stopped, the

suction motor switches off after a delay of approx. 3

seconds. The cleaner now stays in the standby

mode until the electric tool is switched on again.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Aspiradora de Nilfisk-ALTO

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 30 H Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 961-01 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO CENTIX 20 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO Dynamics 440-M/B1 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 30 PC Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 965-0H/M SD XC Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO MAXXI II Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 995-0H/M SD XC Type 22 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO AERO 21-01 PC INOX Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 3 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 3 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 40-0M TYPE 22 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO Handy 2-in-1 Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 30 H Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO Attix 19 Gallon AE Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 50-21 PC CLEAN ROOM Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 30 H Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO AERO 21 INOX Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO 40/PC/XC Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO VC300 Series Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO Attix 19 Gallon AE Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 30 PC Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO SCRUBTEC 653E Manual de usuario

Nilfisk-ALTO

Nilfisk-ALTO ATTIX 130 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario