Nilfisk-Advance GM 810 Manual de usuario

Nilfisk GM 810-811

INSTRUCTIONS FOR USE &

PARTS LIST

Table of Contents

Important Safety Instructions

Warranty

Machine Setup

Using the Machine

Emptying

Disposal

Maintenance/Filter Replacement

Troubleshooting

Loss of Power

Loss of Suction

Parts Explosions

Accessories

Technical Specifications

Contact Information

For Instructions for Use on HEPA/ULPA filter installation, please refer to

the addendum titled, “ABSOLUTE FILTERS – End User Information.”

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE USING THE

MACHINE. DEPENDING ON LOCAL REGULATIONS AND THE COMPOSITION

OF THE MATERIALS YOU HAVE COLLECTED, THERE MAY BE

REQUIRMENTS FOR SPECIAL HANDLING AND DISPOSAL OF THE

COLLECTED DEBRIS. CONSULT YOUR LOCAL OCCUPATIONAL SAFETY AND

HEALTH ADMINISTRATION (OSHA) AND ENVIRONMENTAL PROTECTION

AGENCY (EPA) OFFICIALS FOR DETAILS.

CAUTION: This Nilfisk vacuum cleaner or any other vacuum cleaner is not to be used in

explosion-hazardous areas, as serious injury could result.

Under no circumstances may this cleaner safely be used for the collection of hazardous or

toxic materials unless equipped with a special HEPA (High Efficiency Particulate Air)

filter and bag which have been installed according to written instructions from Nilfisk-

Advance.

ATTENTION EMPLOYER: Please ensure these Instructions for Use are made available

and understood by your employees or any other persons who may use this equipment.

To list all toxic and hazardous materials would be beyond the scope of these Instructions.

It is the Employer's responsibility to identify, for Employees' and others' information,

hazardous or toxic materials which may be collected by this equipment.

Your new Nilfisk industrial vacuum cleaner is a precision-engineered instrument

designed for exceptionally fine filtration. Ordinary vacuum cleaners do not have HEPA

filters, and cannot be safely used for hazardous dust collection. This Nilfisk machine is

safe to use with fine powders or hazardous materials, as long as certain precautions are

taken. Proper care of this cleaner is essential to the maintenance of its ultrafine filtering

capabilities.

BEFORE USE: DO NOT ATTEMPT TO OPERATE THIS CLEANER UNTIL YOU

HAVE INSTALLED ITS VARIOUS COMPONENTS ACCORDING TO THE

FOLLOWING INSTRUCTIONS:

WARRANTY

The Nilfisk companies warrant that Nilfisk equipment will be free of defects in

workmanship or material for a period of two years from the date of delivery. Should any

failure to conform to this warranty appear, the Nilfisk companies shall upon notification

within such time period, correct such non-conformity, at its option, either by repairing

any defective part or parts, or by replacing a part or parts provided that the equipment is

returned to an authorized Nilfisk service facility. In all cases freight both ways will be at

the expense of the customer. Equipment shall not be returned without advance notice to,

and consent of the Nilfisk companies.

EXCEPT AS SPECIFICALLY SET FORTH HEREIN, THE NILFISK COMPANIES

MAKE NO WARRANTIES, EITHER EXPRESSED OR IMPLIED AS TO ANY

MATTER WHATSOEVER, INCLUDING WITHOUT LIMITATION ANY AND ALL

WARRANTIES OF MERCHANTABILITY, FITNESS FOR PURPOSE, OR OTHER

WARRANTIES, ALL OF WHICH ARE EXPRESSLY DISCLAIMED AND

EXCLUDED. NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES,

INCLUDING BUT NOT LIMITED TO LOSS OF PRODUCTION, LOSS OF TIME,

LOSS OF PROFITS OR OTHER SIMILAR INDIRECT LOSSES WHICH MIGHT

OCCUR AS A RESULT OF DEFECTS, PARTIAL OR TOTAL FAILURE OF THE

PRODUCT TO PERFORM AS SPECIFIED.

Correction of non-conformities or defects in the manner and for the period of time

provided above, shall constitute fulfillment of all liabilities of the Nilfisk companies to

the customer, whether based on contract, negligence or otherwise with respect to, or

arising out of such equipment. The remedies set forth herein are exclusive, and the

liability of the Nilfisk companies with respect to this sale or anything done in connection

therewith, whether in contract, in tort, under any warranty, or otherwise, shall not except

as expressly provided herein, exceed the price of the equipment or part on which such

liability is based.

The warranty does not cover repairs due to normal wear and tear, accident, neglect,

misuse or abuse, incorrect installation or use other than as described in the

instruction booklet. Breaks in hoses and cables are not covered. This warranty is

rendered void if the motor number plate is removed or defaced or if repairs are

made or attempted by persons not authorized by the Nilfisk companies.

MACHINE SET-UP:

Before turning on the motor: Install the microfilter (#117304-10-

Felt, #017230-AES Polycomposite, #017220-01-Gore-Tex®), the

small felt sock, on the bottom of the motor by sliding the filter over

the motor bottom, and covering as much of the bottom as the depth

of the filter will permit (photo 1). Be sure the filter's elastic collar

holds the filter snugly in place and is as high up on the motor

bottom as possible.

2. Next, mount the HEPA/ULPA filter (#01710104XX /

01710204XX) according to the accompanying bulletin. Place the

motor back in the cavity in the top of the cleaner (photo 2). Fasten

the motor head in place using either the positive twist safety

latches or the standard latches, depending on which option you

purchased.

Photo 1

Photo 2

3. Installing the Polyliner and Paper Bag: Twist and release the

two positive twist safety latches, or the standard latches,

depending on your machine. They are located on the body of the

container, front and back. Lift off the top. Open the polyliner and

place in the bottom of the container with its walls flush against the

container sides and lipped under the container inlet (photo 3). The

excess length of polyliner is draped over the top of the container

and down the outside then rolled at the end to permit the container

clips to close.

Install a paper bag inside the polyliner according to the

illustrations printed on the paper bag itself (photo 4). Replace the

top container and fasten the two clips.

Note: Polyliners are optional. If you choose not to use a polyliner,

follow the instructions to install the paper bag.

4. The GM 810 and GM 811 offer a wide variety of hoses and accessories. Consult your

local District Sales Managers or Customer Service Department at (800)-NILFISK for a

list of optional hoses and accessories. No matter what hose option you have chosen, it can

be connected in the following manner. Affix the vacuum hose to the vacuum by inserting

it into the orifice on the lower container. Once it is inserted, rotate the inlet coupler a

quarter turn to lock it into place. Consult your District Manager or the Customer Service

Department if you have any problems attaching the accessories you have purchased.

USING THE MACHINE:

Correct use of the machine: This machine is not a wet/dry vacuum. It is intended for

dry collection only. Do not use this vacuum to pick up liquids, or any wet materials.

EMPTYING:

IF THIS VACUUM CLEANER IS USED TO COLLECT HAZARDOUS MATERIAL,

DO NOT ATTEMPT TO OPEN OR EMPTY ITS CONTENTS WITHOUT PERSONAL

PROTECTIVE CLOTHING AND RESPIRATORY PROTECTION.

Photo 3

Photo 4

Starting and stopping: Press the gray button on the upper

front portion of the vacuum (photo 5).

Photo 5

Photo 6

DISPOSAL:

Depending on local regulations, and the composition of the material you have collected,

there can be a requirement for special handling and labeling of the filled and sealed

plastic bags. Consult you local Occupational Safety and Health Administration (OSHA)

and Environmental Protection Agency (EPA) official for details.

MAINTENANCE

Routine Maintenance:

To ensure maximum performance of your Nilfisk vacuum cleaner, be sure to check your

main filter regularly. Your filter may need to be shaken to remove caked dust from time

to time.

Filter Replacement:

To ensure that your Nilfisk vacuum cleaner delivers the years of trouble-free operation

for which it was designed, it is necessary to check and replace filters regularly.

1. Main Filter: The large napped cotton bag which is semi-

permanently mounted inside the container will not require

frequent replacement. The main filter must be replaced when

the cleaner no longer develops powerful suction, yet bags are

not full and other filter components are not clogged. Extend

main filter service life by frequent changes of disposable

polyliners and paper bags (photo 7).

2. Microfilter: This small felt polyester sock, which fits over the motor bottom will

require periodic inspection. Dust will discolor the microfilter. Change the microfilter

as soon as any discoloration is easily noticeable. Do not shake this microfilter since

this can cause liberation of potentially harmful microscopic dust into the air.

Carefully remove and discard with collected debris in the sealable poly bag. If

To empty the container and its contents, first turn off the motor.

Allow the cleaner to sit undisturbed for at least thirty (30)

seconds. Then twist and release the container clips. Once the

seal is broken, turn on the motor again. This will prevent

ultrafine particles which are still suspended in the air inside the

container from escaping into the work place. Lift off the

container top. Remove the polyliner and paper bag within it

(photo 6). Then seal off the polyliner with the paper bag inside

and install a new polyliner and paper bag according to step 2,

Machine Setup.

Photo 7

equipped with a Gore-Tex microfilter, the same rules for periodic inspection and

disposal apply. The Gore-Tex microfilter has a clamp that holds it in place. The Gore-

Tex filter must be changed when any abrasions, damage or heavy discoloration is

noticed on the surface of the filter (refer to photo 1).

3. HEPA or ULPA Exhaust Filter: This cartridge is mounted on

the top of the motor, outside the container. If the main filter

and microfilter are properly maintained, the glass fiber

element in the exhaust filter should perform satisfactorily for a

minimum of one year. It cannot be renewed or restored. Exact

life will depend upon frequency of use and amount and type

of material collected. Normally four changes of microfilter

equal one change of HEPA/ULPA filters. Remove the

protective metal casing and replace the pleated glass fiber

cartridge according to the accompanying instructions (photo

8). Cartridges must be replaced more frequently if the cleaner

has had unusually heavy use, or if the various pre-filters have

been neglected.

CAUTION: Use only genuine Nilfisk replacement filter components. The use of

substitute components could pose a grave risk of personal exposure, and will cause all

equipment warranties to be void.

TROUBLESHOOTING

Loss of Power:

1. Make sure the power cord is properly fastened to the motor head, and it is properly

plugged into the socket.

2. Be sure the electrical circuit has not blown a fuse.

3. If the circuit is functioning properly, but there is still no power, contact our Customer

Service Department at (800) 645-3475, extension 2.

Loss of Suction:

If the GM 80 loses suction power during operation, there may be several reasons,

the most likely of which is a full container. Suction loss is gradual as the container fills

with debris. Check to see if there is any blockage or restriction in the hose.

1) Check the condition of the main filter and microfilter (refer to photos) and determine

whether there is an excessive loading of debris. If there is overloading in the main

filter, you can shake it out. If the microfilter is loaded, or there is any other problem

with the microfilter, it needs to be replaced. Call our Customer Service Department at

(800) 645-3475, extension 2 to order replacement filters.

2) If all fails, call our Customer Service Department at (800) 645-3475, extension 2.

Photo 8

GM 810

No.

Item No. Description

Qty.

1 115448-11

UPPER CONTAINER W/

COTTON FILTER

2 121103-29

MOTOR COMPLETE

120 V

3 115447-10

LOWER CONTAINER

4 017091-00

MOTOR HOLD DOWN

RING

5 017092-11

LATCH

6 805521-00

WASHER

7 815406-00

SCREW, 4MM X 5MM

8 705265-10

NUT, 4MM ESN

9 712386-00

SPRING CUP

10 017093-16

KEEPER

11 815407-00

SCREW, 4MM X 10MM

12 705265-10

NUT, 4MM ESN

13 815406-00

SCREW, 4MM X 5MM

14 815406-00

SCREW, 4MM X 5MM

15 815407-00

SCREW 4MM X 10MM

16 805521-00

WASHER

17 017092-11

LATCH

18 017094-10

ADAPTER

19 017093-05

KEEPER

20 815412-00

SCREW 4MM X 6MM

21 705265-10

NUT, 4MM ESN

22 815419-00

RING

23 815418-00

GASKET

24 815417-00

SOCKET

25 814312-00

SCREW

GM 811

No.

Item No. Description

Qty.

1 115448-11

UPPER CONTAINER

W/ COTTON FILTER

2 121103-29

MOTOR COMPLETE

120 V

3 017020-00

LOWER CONTAINER

4 017091-00

MOTOR HOLD DOWN

RING

5 017092-11

LATCH

6 805521-00

WASHER

7 815406-00

SCREW, 4MM X 5MM

8 705265-10

NUT, 4MM ESN

9 712386-00

SPRING CUP

017093-16

KEEPER

815407-00

SCREW,

4MM X 10MM

815406-00

SCREW, 4MM X 5MM

805521-00

WASHER

815406-00

SCREW, 4MM X 5MM

017094-01

ADAPTER

805521-00

WASHER

017092-11

LATCH

815407-00

SCREW

705265-10

NUT

815418-00

GASKET

815419-00

RING

815417-00

SOCKET

814312-00

SCREW

017099-43

NUT, 3/8 ESN

017024-11

NUT, ESN

017847-00

WHEEL

017848-00

CASTER, SWIVEL

017078-05

CASTER BRACKET

017078-15

WHEEL BRACKET

017643-00

BOLT 5/16 X 3/4

017645-00

WASHER

017644-00

NUT, HEX

017672-00

WASHER

017849-00

HUB CAP

017078-11

WHEEL BOLT

017877-27

SCREW 8-32 X 1/2

017093-02

KEEPER

815407-00

SCREW 4MM X 10MM

705265-10

NUT, 4MM ESN

HEPA Filter Kit (017104XX)

ULPA Filter Kit (017204XX)

No. Item No. Description

1 217377-01 HANDLE

2 717376-00 FILTER COVER

3 017247-01 HOLD DOWN PAD

4 017009-01 SEAL, FOAM, HEPA

5 813950-00 SCREW

6 821070-00 FILTER BASE

7 017010-05 SEAL,FOAM, BOTTOM

8 017276-31 HEPA FILTER (includes

item numbers 3, 4, 7)

8 017376-31 ULPA FILTER (includes

item numbers 3, 4, 7)

No. Item No. Description

1 21573001

EXHAUST WITH DIFFUSER

1 22394900

EXHAUST FILTER WITH MICRO

STATIC DIFFUSER

2 11693700

DIFFUSER FILTERS 2 PCS

3 11641000

MICRO-STATIC FILTER

4 11730410

MICROFILTER

5 22132000

HANDLE COMPLETE

6 81585000

DUST BAG

Filter, Filter Bag and Trolley

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Aspiradora de Nilfisk-Advance

Nilfisk-Advance

Nilfisk-Advance VC300 Series Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VP300 eco Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VHC200 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VP600 US Manual de usuario

Nilfisk-Advance

Nilfisk-Advance WD 215 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Coupe Manual de usuario

Nilfisk-Advance

Nilfisk-Advance UZ 934 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance ALTO ATTIX 200 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Bravo Manual de usuario

Nilfisk-Advance

Nilfisk-Advance AERO 20 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance IVT 1000 CR Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 930 Guía

Nilfisk-Advance

Nilfisk-Advance ATTIX 7 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance ECO OIL 13 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VHS 42 HC Manual de usuario

Nilfisk-Advance

Nilfisk-Advance BackVacuum XP Manual de usuario

Nilfisk-Advance

Nilfisk-Advance UZ 964 Ergoclean Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 110 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 930 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Coupe Neo Manual de usuario

Nilfisk-Advance

Nilfisk-Advance ATTIX 50 M Manual de usuario

Nilfisk-Advance

Nilfisk-Advance UZ 868E Manual de usuario

Nilfisk-Advance

Nilfisk-Advance AERO 26-2L PC Manual de usuario

Nilfisk-Advance

Nilfisk-Advance 118 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario