Night Owl H2THD Manual de usuario
QUICK SETUP GUIDE
H2THD
SECURITY SYSTEMS
Home
&Business
QSG-H2THD.indd 1 2018/6/22 11:00
1
What’s in the Box
Package Contents
DISCLAIMER: The exact components of your system, images and quantities may vary depending on
your model number. While these may vary, this QSG will address the setup and initial configuration
of your DVR and cameras.
DVR Camera(s)
(x4)
IP Camera(s)
(x2)
Mounting
Template
60 ft. Video/Power Cables
(1 cable per camera)
Power Splitter(s)
(1 per 4 cameras)
USB Mouse (x1)
Metal Base
(1 per IP camera)
6 ft. HDMI
(x1)
DVR Power
Adapter
(x1)
Camera Power
Adapter(s)
(1 per 4 cameras)
IP Camera
micro USB cable(s)
(1 per IP camera)
USB
Power Supply
(1 per IP camera)
6 ft. Ethernet
(x1)
Safety Sticker (x3)
Mounting Hardware
Items Not Included
NOTE: Monitor is required
for initial setup.
Router
RESET LAN1 LAN2 LAN3 LAN4 WAN
Monitor
IMPORTANT: For best results, use all the included Night Owl accessories. Third-party
accessories may not work properly.
QSG-H2THD.indd 2 2018/6/22 11:00
2
DVR Rear View
Sync – Press and release to sync the DVR with the wireless cameras.
Video Inputs – Allows for the connection of BNC cameras.
USB Ports – Allows for the connections of a USB mouse and/or a USB flash drive.
You will connect the included USB mouse to assist you in navigating the DVRs menu
interface. You will connect a USB flash drive to download video files from the DVR
and save them to your USB flash drive.
HDMI Output – Allows for the video connection. If the TV/Monitor has an HDMI
input, connect the HDMI cable from the HDMI output port on the DVR to the HDMI
input port on your TV/Monitor. NOTE: Preferred method.
VGA Output – Allows for the video connection. If the TV/Monitor has a VGA input,
connect the VGA cable from the VGA output port on the DVR to the VGA input port
on your TV/Monitor. (VGA Cable not included)
Audio Inputs & Outputs – Allows for the connection of an audio-enabled camera
or self-powered microphone and an external speaker to the DVR. (Audio enabled
camera, microphone and speaker not included)
RJ-45 (Ethernet) Port – Used to connect the DVR to your router/modem via the
included Ethernet cable.
Power Input – Used to connect the included 12V DC power supply.
Power Switch – Use this switch to power ON/OFF the DVR. Make sure the power
switch is in the ON position before attempting to use the DVR.
Antennas – Connection for the included antennas.
Images used are for reference only. Your product may vary slightly.
A 4 channel model is displayed above.
1
2
3
4
5
6
7
8
9
10
Product Overview
2
WIRED /SYNC
31
1010
5 6 8
9
NOTE: Not all models have a
power switch on the DVR.
47
QSG-H2THD.indd 3 2018/6/22 11:00
WIRED /SYNC
WIRED /SYNC
WIRED /
SYNC
3
HDMI HDMI
USB
Connecting Your System
NOTE: Monitor is required for initial setup. To
view cameras, TV/Monitor must be tuned to
the same Input the HDMI is plugged into.
(Router Not
Included)
ETHERNET
Plug the other end of the
Ethernet cable into a numbered
port on the back of the router.
5
STOP: BEFORE installing, test
each camera locally to confirm they
function properly.
DISCLAIMER: Camera/cable quantities may vary.
ETHERNET
Plug included HDMI cable into
the HDMI port on the back of
the DVR.
1Plug the other end of the HDMI
cable into the back of the TV
or Monitor.
2
Plug the USB mouse into the USB
port on the back of the DVR.
3Plug the included Ethernet cable
into the LAN port on the back of
the DVR.
4
QSG-H2THD.indd 4 2018/6/22 11:00
4
WIRED /SYNC
WIRED /SYNC
NOTE: Make sure you twist and lock BNC connectors.
NOTE: Some systems will beep upon booting up.
Connect the BNC connector of the
video/power cable labeled TO DVR
ONLY to an open video input on
the DVR.
2
FROM Camera TO Camera
Connect the ends of the cable
attached to the camera to the
ends of a video/power cable
labeled TO CAMERA ONLY.
1
NOTE: Audio enabled cameras will have
a white RCA connector to transmit audio
signal (Optional).
Connect the red female power
leads of the video/power cables
to the male power splitter ends.
3
Power Cable
Connectors
Power Splitter
Connectors NOTE: Power adapters are labeled TO CAMERA
ONLY and TO DVR ONLY.
NOTE: Check that the UPS or surge protector
is switched ON.
Connect the power splitter to the
camera power adapter and plug the
adapter into a surge protector or
Uninterruptible Power Supply (UPS).
4
Connect the DVR power adapter
to the Power Input on the rear
of the DVR.
5Plug the DVR power adapter into a
surge protector or Uninterruptible
Power Supply (UPS).
6
(Surge
Protector Not
included)
Power
splitter
Camera Power
Adapter
Surge Protector
(Not included)
Connecting Your Wired Cameras
QSG-H2THD.indd 5 2018/6/22 11:00
5
Connecting Your Wireless Indoor IP Cameras
You MUST test the Wireless Indoor IP Cameras locally before
mounting. (DO NOT MOUNT OUTDOORS. SERIOUSLY!)
Plug the camera(s) in next to the DVR to make sure video is
transmitted. The camera(s) are already in pairing mode.
Insert the small end of the micro USB cable into the camera and the other
end into the USB power supply.
Plug the power supply into a socket or a UPS (Uninterruptible Power Supply).
1
2
micro USB Cable
OR
USB Power Supply
QSG-H2THD.indd 6 2018/6/22 11:00
6
Be patient as the camera(s) power up. It may take a couple of minutes. Enjoy
a refreshing beverage while you wait.
Once the camera(s) are powered up, video will be transmitted to the DVR.
Easily move the camera from
location to location. Just plug it
in and let it do what it does best.
The magnetic base makes
mounting simple.
3
4
NOTE: If you see the camera(s) live view, you can move the camera(s) to the mounting
location(s). If you no longer see the live view after moving the camera(s) to their
mounting location, the camera may be too far from the DVR.
QSG-H2THD.indd 7 2018/6/22 11:00
Recovery Email Address
Please ensure you provide a valid email address
in case your ever forget your account information.
NOTE: You MUST enter a VALID email address. If you
don’t, you will have to call Tech Support to reset your
password, and that just seems like a waste of time.
Remember Your Password
Night Owl®strongly recommends writing down your
password within the Quick Setup Guide. You will need
it every time you log into your DVR and to remotely
view on a Smart Device.
Important… Please Read
Startup Wizard
7
Admin Account Creation
By default, the username will be admin. It must
remain admin upon your initial account configuration.
However, you may add additional users at a later time.
NOTE: Password can be any alphanumeric combination
between 6 and 20 characters.
1When you power on the DVR
you will be prompted with the
following screen. Please follow
the instructions to complete the
Startup Wizard.
Booting Up for the First Time
On the Password Creation screen, please note the following:
2
Write your
password here:
QSG-H2THD.indd 8 2018/6/22 11:00
8
At this stage of the Startup Wizard, you will be instructed on adjusting
the camera sensitivity and setting the Motion Detection Area. Having
your cameras in their final position will be key.
To detect motion for the front door to your home, place the camera to
the side of the entrance.
NOTE: Need more help configuring your DVR? Please refer to the owner’s manual located
on the support page at www.NightOwlSP.com.
This is the last screen you will
see when you have successfully
completed the Startup Wizard.
4
NOTE: If your camera
has an infrared sensor,
it works best for ‘side to
side’ movement across
the camera’s field of
view as opposed to
directly to or away from
the camera.
When you reach the Camera / Channel Settings screen, you will want
to have installed the cameras in their final position. Please make sure
you have mounted cameras at least 7ft. above the ground and angled
them slightly down.
3
QSG-H2THD.indd 9 2018/6/22 11:00
9
You must confirm your password
by entering it a second time.
Click “OK” to save the changes.
Did you forget your password?
Right click the mouse to bring
up the system menu. Select
the login screen. Click on the
“Forget Password” button.
1
A reset code will be sent to the email address entered during account setup.
2
Log into your email to retrieve the reset password code.
3
Open the email from “resetcode” and locate the six-digit code.
A
Return to your system and
enter the six-digit code into
the “Secure Code” field.
Then, click “OK” to continue.
B
Once you’ve entered the Secure
Code, you will be prompted to
create a new password.
4
NOTE: Make sure you enter a VALID email address. This process is way better
than waiting on hold to talk to a support rep. Seriously!
NOTE: Please check your junk/spam folder if you don’t see the email in your inbox.
NOTE: This may take a few minutes. Be patient! Maybe grab a quick snack?
Password Reset Instructions
QSG-H2THD.indd 10 2018/6/22 11:00
Tabla de contenidos
Otros manuales de Sistema de seguridad de Night Owl
Night Owl
Night Owl NODVR108 Series Manual de usuario
Night Owl
Night Owl K-16 Series Manual de usuario
Night Owl
Night Owl C50XFR Series Manual de usuario
Night Owl
Night Owl THD301 Series Manual de usuario
Night Owl
Night Owl S44245NHD Manual de usuario
Night Owl
Night Owl FS84500 Manual de usuario
Night Owl
Night Owl CAM-4PK-724 Manual de usuario
Night Owl
Night Owl FS-8320 Manual de usuario
Night Owl
Night Owl WNVR-NC Series Manual de usuario
Night Owl
Night Owl WNVR201 Series Manual de usuario
Night Owl
Night Owl AHD7-882 Manual de usuario
Night Owl
Night Owl CAM-4PK-DM724 Manual de usuario
Night Owl
Night Owl 16 Channel H.264 Video Security Kit Manual de usuario
Night Owl
Night Owl WG4 Series Manual de usuario
Night Owl
Night Owl VDP2 Series Manual de usuario
Night Owl
Night Owl NONB-44500 Manual de usuario
Night Owl
Night Owl HDA30 series Manual de usuario
Night Owl
Night Owl BUL series Manual de usuario
Night Owl
Night Owl HAWK-74250 Manual de usuario
Night Owl
Night Owl XHD Series Manual de usuario
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario