Niche Zero Manual de usuario
1
Niche Zero User Manual
2
Niche Zero Manual 1
Contents 2
Important Safeguards 3-5
Electrical safety 6
Trouble shoong 7
First use of Niche Zero 8
Using the Niche Zero 9-10
Care and Cleaning 11-14
Guarantee 15-16
Contents
3
Important Safeguards
When using electrical appliances, basic safety precauons should
always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE
REFERENCE
WARNING: Misuse of this
appliance may cause injury.
1. Before using for the rst
me please ensure that
your electricity supply is the
same as shown on the rang
label on the underside of the
Niche Zero. If you have any
concerns, please contact your
local electricity company.
2. Never use a plug without the
fuse cover ed. Always make
sure a replacement fuse is the
same rang as the original.
3. If the supply cord or plug is
damaged, or if the appliance
malfuncons or has been
damaged in any manner; it
must be replaced or repaired
by the manufacturer, its
service agent or similarly
qualied persons in order to
avoid a hazard.
4. Replacement fuses should
be approved to BS 1362
(UK only).
5. Any plug cut from its power
supply cord should be
disposed of immediately.
Inserng a cut-o plug into an
electrical socket is dangerous.
6. The Niche Zero features an
overheat cut-out that cuts the
power if it becomes too hot
for any reason. If this occurs,
unplug the grinder. The safety
cut-out will automacally
reset itself within 1 hour and
the power will be restored
when the Niche Zero is
plugged in again.
7. Do not place the Niche Zero
on or near a hot gas or electric
burner, or where it could
touch a heated surface.
4
Important Safeguards
8. Any signicant spillage
onto the surface under or
around the Niche Zero, or
onto the Niche Zero itself,
should be cleaned and
dried before connuing to
use the Niche Zero.
9. To protect against electric
shock and damage do not
immerse any part of the
Niche Zero in water or allow
moisture to come in contact
with these parts. Do not
operate the Niche Zero on a
sink draining board.
10. The burrs are extremely
sharp; take extra care when
handling these internal parts,
especially when removing
from the body during
cleaning. Avoid touching the
sharp edges.
11. To avoid suocaon and
choking hazard for young
children, remove and safely
dispose of the protecve
cover ed on the power plug
pins and any plasc bags.
12. Avoid contact with
moving parts.
13. The Niche Zero Grinder can
be used by adult persons
with reduced physical,
sensory or mental capabilies
or lack of experience and
knowledge, if they have
been given supervision or
instrucon concerning use of
the Niche Zero Grinder in a
safe way and understand the
hazards involved.
14. The Niche Zero must not
be used or played with by
children. Keep the Niche Zero
and its cord out of the reach
of children.
15. Always make sure the Niche
Zero is properly assembled
before use. The Niche Zero
will not operate unless
properly assembled and the
lid is closed.
16. Do not aempt to operate
the Niche Zero by any
method other than for which
it is intended and described
in this booklet.
5
Important Safeguards
17. The Niche Zero is not intended
to be operated by means of
an external mer or separate
remote control system.
18. The use of aachments not
recommended or sold by
Niche may cause re, electric
shock or injury.
19. Check your beans in the bean
funnel for the presence of
foreign objects before using.
20. The Niche Zero is for
household use only. Do
not use the Niche Zero for
anything other than its
intended use. Misuse may
cause injury. If the Niche Zero
is used improperly or not
used in accordance with these
instrucons, the guarantee
will become invalid and
Niche refuses any liability for
damage caused.
21. Do not place the Niche Zero
near the edge of a bench
or table during operaon.
Ensure the surface is level,
clean and free of water. Do
not let the power cord hang
over the edge of a table,
counter, touch hot surfaces or
become knoed.
22. The Niche Zero is designed
to only grind whole roasted
coee beans. Do not aempt
to grind any other foodstus
including herbs, spices and
pre-ground coee.
23. Always disconnect the Niche
Zero from the supply if it is
le unaended and before
assembling, disassembling or
cleaning. To unplug it, hold
the plug and pull it out of the
socket. Never pull it out by the
power cord.
24. Do not put the Niche Zero,
or any of its parts in the
dishwasher.
25. Keep the Niche Zero clean.
Refer to Care and Cleaning.
26. Do not use the Niche Zero
outdoors.
27. Never tamper with the safety
systems. They are included for
your personal safety.
6
Electrical requirements
UK, EU and Australia: 220-240 Volts A.C. 50-60 Hz
US: 110-120 Volts A.C 50-60Hz
NOTE: The Niche Zero grinder has a
grounded/earthed plug. To reduce the risk
of electrical shock, this plug will t in an
outlet only one way. If the plug does not t
in the outlet, contact a qualied electrician.
Do not modify the plug in any way. A
power-supply cord storage area is provided
inside the Niche Zero to reduce the risk
resulng from the power cord becoming
entangled or tripping over a longer cord.
If a longer extension cord is used:
The marked electrical rang of the extension cord should be at least
as great as the electrical rang of the Niche Zero. The extension cord
should be a grounding-type cord. The cord should be arranged so
it will not drape over the countertop or table top where it can be
pulled on by children or tripped over.
The symbol shown indicates that this appliance
should not be disposed of in normal household
waste. It should be taken to a local authority
waste collecon centre designated for this
purpose. For more informaon, please contact
your local council oce.
7
Troubleshoong
Niche Zero does not run when switched on:
Check to see if the Niche Zero is plugged into a grounded outlet and the
lid is closed. If it is, unplug the Niche Zero, then plug it back in again. If
the Niche Zero sll does not work, check the plug fuse or circuit breaker
on the electrical circuit the Niche Zero is connected to and make sure the
circuit is closed. If the Niche Zero does not run aer taking these steps, a
foreign object may be jamming the cung burrs. See “Care and Cleaning”
for more informaon.
Niche Zero runs when switched on but coee does not grind:
The burrs require cleaning or are worn. Also check that the grind seng
isn’t set to calibrated as this means the burrs are touching.
See “Care and Cleaning” for more informaon.
Niche Zero is operang normally, but stops abruptly:
Immediately turn o the Niche Zero. A foreign object, such as a pebble,
piece of metal or twig, may have jammed the burrs.
See “Care and Cleaning” for more informaon.
Grind size seems incorrect for chosen seng:
Check the Niche Zero is correctly calibrated.
See recalibraon of Niche Zero in “Care and Cleaning”.
Cord does not pull out from base:
Unplug the Niche Zero. Unscrew and remove the wooden base cover and
check that cord has not knoed. Extend cord, replace wooden base cover
then push cord back into base.
8
First Use of Niche Zero
WARNING: do not use when set to calibrated as you will damage the burrs.
There may be coee residue in your grinder. If there is, this is from tesng
to make sure your grinder performs to its best.
If you require an extra coarse seng, you are able to connue rotang the
bean funnel an-clockwise unl you reach your chosen seng.
Please note that the grind size markings are only a guide. We recommend
you nd the right sengs that work for you.
9
Using the Niche Zero
Before use remove all packaging.
Plug into outlet, the red LED will glow to show there is power to the Niche
Zero. Your Niche Zero has been factory calibrated and adjusted to seng 20.
1. Open lid and rotate the bean
funnel to the desired grind
seng, matching white dot
on bezel to grind dial number.
Turn clockwise to go ner
(espresso) and anclockwise to
go coarser (press pot). Ensure
you do this with no beans in the
grinder funnel as shown. When
adjusng ner aer coarse
grinding, run the Niche Zero
briey (1 second) every me
the adjustment ring is moved 10
marks on the scale. This ensures
any trapped coee between
the burrs does not strain the
adjustment mechanism and
makes adjusng easier. When
adjusng coarser, the above
procedure is unnecessary.
2. Weigh beans in grind cup, be
vigilant and inspect the beans
to ensure no foreign objects,
that could damage the burrs.
This is also the me to remove
any defecve beans such as
quakers (unusually light beans
compared to others) and blacks
(very dark beans). This all helps
taste in the cup.
3. Open lid and pour beans in
bean funnel.
10
Using the Niche Zero
4. Replace grind cup on
tray underneath.
5. Close lid (Niche Zero will
not operate if the lid is
open) and ick power
switch up, to switch on.
6. You will hear a change in
motor noise when the Niche
Zero has nished grinding.
We recommend to leave it
running for a few more seconds,
to make sure all the beans
have been processed, before
switching o.
7. For espresso, t portalter
over grind cup.
8. Invert grind cup and
portalter, shake and tap
grind cup, then remove.
9. For other brewing methods,
pour ground coee direct
from grind cup into chosen
receptacle.
Tabla de contenidos
Otros manuales de Molinillo de café de Niche
