Baratza Forté Manual de usuario

Tabla de contenidos

Otros manuales de Molinillo de café de Baratza

Baratza

Baratza SETTE 270W Manual de usuario

Baratza

Baratza sette 270 Manual de usuario

Baratza

Baratza Esatto Manual de usuario

Baratza

Baratza Vario Manual de usuario

Baratza

Baratza SETTE 30 Manual de lista de piezas

Baratza

Baratza VIRTUOSO+ Manual de usuario

Baratza

Baratza Forté-BG Manual de usuario

Baratza

Baratza Vario Manual de usuario

Baratza

Baratza Virtuoso Manual de usuario

Baratza

Baratza SETTE 30 Manual de usuario

Baratza

Baratza Preciso Manual de usuario

Baratza

Baratza SETTE 30 Manual de usuario

Baratza

Baratza Encore Manual de usuario

Baratza

Baratza Vario W+ Manual de usuario

Baratza

Baratza Maestro Manual de uso y cuidado

Baratza

Baratza Encore Manual de usuario

Baratza

Baratza SETTE 30 Guía de instalación y uso

Baratza

Baratza Vario Manual de usuario

Baratza

Baratza Encore Manual de usuario

Baratza

Baratza VIRTUOSO+ Manual de usuario

Baratza

Baratza VIRTUOSO+ Manual de usuario

Baratza

Baratza SETTE 30 Guía de instalación y uso

Baratza

Baratza Esatto Manual de usuario

Baratza

Baratza Forte Manual de usuario

Manuales populares de Molinillo de café de otras marcas

SOLAC

SOLAC All4Coffee MC6253 Manual de usuario

Teesa

Teesa TSA4011 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home HG KD 40 Manual de usuario

tomado

tomado TM-1287 Manual de usuario

Aicok

Aicok CG9220 Manual de usuario

Zelmer

Zelmer ZCG7925 Manual de usuario

Isomac

Isomac ROBY Manual de usuario

Eldom

Eldom Dott MK60 Manual de usuario

Bunn

Bunn SAFETY-FRESH 1 GPR Manual de usuario

FAMITEC

FAMITEC BOLD Manual de usuario

Santos

Santos SC55 Instrucciones de funcionamiento

Lumme

Lumme LU-2601 Manual de usuario

TREVIDEA

TREVIDEA Girmi MC02 Manual de usuario

Eureka

Eureka Zenith E Manual de instrucciones

Bunn

Bunn HVG Manual de instrucciones y seguridad

SEVERIN

SEVERIN KM 3878 Guía del usuario

Bosch

Bosch SOLUTION 6000 Manual de usuario

Imetec

Imetec MACINACAFFE Manual de usuario

1

Forté Power Board Replacement

*** Be sure to have a soft work surface like a towel to prevent the polished casing from being scratched***

*** Read entire document before removing motor***

Tools Required:

Standard Phillips screw driver, Offset ratchet Phillips screw driver, Baratza calibration tool or 2mm Allen

wrench

Procedure:

-Case Removal-

1. Clear beans out of the hopper and run the unit briefly to clear any leftover beans from between

the burrs.

2. UNPLUG GRINDER

3. RAISE BOTH LEVER ARMS ALL THE WAY TO THE TOP

4. Remove the 2mm case screw on the top rear of the casing, using our calibration tool

5. Invert the grinder. Using side cutters, remove the rear two feet (ONLY THE REAR FEET)

2

6. Remove the Philips self-tapping screws from beneath the rear two feet.

3

7. Place the grinder right side up and pull the case off from the rear.

-Motor Removal-

1. Mark the motor tension screw and motor tension plate with a light colored paint pen for rotation

reference. This step is crucial for achieving proper belt tension after re-installation.

2. Rotate the screw exactly 1080 degrees (three full rotations) counterclockwise when loosening.

4

3. Loosen the motor tension screw, but do not remove it from the tension mount.

4. Remove the two Phillips motor mount screws (#1291) holding the motor in place using the offset

Phillips ratchet.

5. Unplug the motor from the main power board.

6. You will find it easiest to set the grinder on its face. Unplug all of the connectors that go

into the circuit board. ** Take note where all of wires plug into on the board- they must

go back in the same exact way.

5

7. Remove the four, gold screws that retain the circuit board. You may find it necessary to

pull up on the big blue box with one hand, while unscrewing the screws with the other.

8. Once the screws are removed, pull the circuit board out, fix the issue or replace.

9. Set the circuit board back into the machine and tighten all of the screws. The screws do

not need to be torqued down.

10. Plug in all of the connectors, and make sure that they are fully seated before continuing.

6

-Reinstall Motor-

1. Plug the new motor into the main power board.

2. Attach the green ground wire to the screw hole directly right of the tensioning screw.

3. Insert the Phillips motor mounting screws and hand tighten. You may need to use the offset

ratchet to get the screws in far enough. (Do not completely tighten so motor tension can be

adjusted.)

4. Tighten the motor tension screw to the same gap measured before disassembly. Before

tightening apply locktite to the screw (finger nail polish can be substituted for locktite.)

5. Tighten the two Phillps motor mounting screws completely.

6. Reinstall the case.

If you have any questions or concerns, please email support@baratza.com or call at 425-641-1245.