Nice Titan 912L Manual de instalación y funcionamiento

EN -Installation and reference manual

IMPORTANT -These instructions apply only to the 912L actuator. Control box

installation/operation is described in a separate control box manual.

Linear actuator

TITAN12L/12L1 912L

912L LA

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

CONTENTS

SECTION 1: TITAN 912L ACTUATOR OVERVIEW .....................................3

SECTION 1: TOOLS NEEDED FOR INSTALLATION .................................4

SECTION 2: INSTALLATION SAFETY ........................................................4

SECTION 3: ACTUATOR - MECHANICAL INSTALLATION .......................5

3.1 MANUALLY SET GATE OPEN/CLOSE LIMITS .....................12

3.2 RUN ACTUATOR CABLE(S) TO CONTROL BOX .................13

3.3 936 CONTROL BOARD WIRING: PULL-TO-OPEN ...............14

3.4 936 CONTROL BOARD WIRING: PUSH-TO-OPEN ..............15

3.5 1050 CONTROL BOARD WIRING: PULL-TO-OPEN .............16

3.6 1050 CONTROL BOARD WIRING: PUSH-TO-OPEN ............17

3.7 SETTING ACTUATOR FINE LIMITS .......................................20

3.8 ACTUATOR CABLE REPLACEMENT WIRING ...................... 22

SECTION 4: PART DRAWINGS ....................................................................23

Warranty ..........................................................................................................24

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

• TITAN 912L-1 = Actuator with 12’ harness

• TITAN 912L-2 = Actuator with 42’ harness

(dual gate only)

PIVOT ARM (P/N 1116)

ACTUATOR BOLT KIT

(P/N 1125)

GATE BRACKET,

BLACK

(P/N 10025215)

TITAN912L ACTUATOR PARTS IDENTIFICATION

PART# DESCRIPTION QTY

912L-1 Actuator With 12 foot Harness 1

912L-2 (DUAL GATE ONLY) Actuator With 42 foot Harness 1

1116 Pivot Arm 1

10025215 or PD0959A0000 Gate Bracket (Black) 1

1125 Actuator Bolt Kit 1

TITAN912L ACTUATOR SPECIFICATIONS

Drive Electromechanical Stainless Steel Screw

Gate Length And Weight Max. • Up to 600 lb. for 20 foot leaf (272 kg for 6 m)

• Up to 1000 lb for an 8 ft leaf (453 kg for 2.4 m)

Open/Close Time (To 90°) 14 - 16 seconds (adjustable)

Temperature Rating -4º to 122º F (-20º to 50º C)

Operating Voltage 12VDC

Actuator Dimensions (LxWxD) 43 x 4 x 6.75 inches (109.2x 10x 17.5 cm)

User Controls 936 or 1050 control board

Listed To Ul325 936, 1050, or Mercury 310 Control Boards:

Usage Class I, II, III, IV

Actuator Weight 19.75 pounds (8.96 kg)

Congratulations on selecting a Nice TITAN 912Lactuator. With proper selection, system design, installation and

maintenance this operator should provide years of reliable operation. This manual covers ONLY the installation

of the TITAN 912L actuator.

SECTION 1: TITAN 912L ACTUATOR OVERVIEW

IMPORTANT!

For control box installation, wiring, operation, maintenance instructions and all safety information,

refer to the appropriate control box installation manual used for the system being installed.

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

Below is a list of tools necessary for installation of the Titan actuator:

• Welder (for pivot arm) unless optional bolt-on pivot arm (P/N 446) is used.

• Basic hand tools (screwdrivers, wrenches, pliers, etc..)

• Torx 25 tool (for removing actuator cover screws)

• Level (for ensuring pivot arm and actuator are level).

• Framing square (for determining pivot arm location)

• Torch/Chop Saw (for cutting pivot arm)

• Grinder (for sanding Pivot Arm)

SECTION 2: INSTALLATION SAFETY

SECTION 3: TOOLS NEEDED FOR INSTALLATION

WARNING

READALL SAFETYINFORMATION WHEN INSTALLINGASWING GATE SYSTEM! SEE EITHER OF THE

FOLLOWING MANUALS FOR SAFETY INFORMATION:

• CBOX936 Control Box Installation and Program Manual (with 936 controller).

• CBOX1050 Control Box Installation and Program Manual (with 1050 controller).

• MB1050 Control Box Installation an Program Manual (with 1050 controller).

• ACBOX/SolarBOX Installation and Program Manual (with Mercury 310 controller)

CAUTION

’Disconnect power at the control panel before making any electric service power connections.

’Be aware of all moving parts and avoid close proximity to any pinch points.

IMPORTANT!

’The gate operator installation is NOT a “do-it-yourself” project. Contract a qualied gate operator installation

company to install this system to ensure a safe and reliable installation.

’It is the responsibility of the property owner to ensure the installer is qualied to carry out the installation in

a safe and professional manner.

’Consult local government agencies for up-to-date rules and regulations to satisfy licensing, codes or

regulations that regulate automated gate system design and installation.

’The gate for which the gate operator is intended to be used should itself be installed correctly so that it is

level and plumb and the gate opens easily and evenly.

’Note that Nice swing gate systems are not intended for installation on an incline.

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

LEFT SIDE VERTICAL VIEW

FIG-1A: "PULL TO OPEN" PIVOT ARM INSTALLATION

INSTALL PIVOT ARM TO GATE: PULL-TO-OPEN

1. Securely mount the pivot arm to the hinge post (FIG-1A).

2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are

taken from the center of pivot of the gate hinge.

3. It is strongly recommended to weld the pivot arm to the hinge post.

TOP VIEW

6” 6”

13” 13”

SECTION 4: ACTUATOR - MECHANICAL INSTALLATION

PIVOTARM PIVOTARM

PIVOTARM

1/2”

HINGE POST

CENTER OF HINGE

CENTER LINE OF

ATTACHMENT POINT

FOR GATE BRACKET

CENTER OF HINGE

GATE CLOSED

DIRECTION OF OPENING

HINGE POST HINGE POST

NOTICE

Welding is much

preferred, but Nice

offers an optional

bolt-on pivot arm

(P/N 446) for when

welding is not

possible.

CAUTION

Never weld parts to the gate or posts when the control board

is powered to avoid irrepairable damage to the circuit board!

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

FIG-1B: "PUSH TO OPEN" PIVOT ARM INSTALLATION

1. Securely mount the pivot arm to the hinge post (FIG-1B).

2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are

taken from the center of pivot of the gate hinge.

3. It is strongly recommended to weld the pivot arm to the metal post.

INSTALL PIVOT ARM TO GATE: PUSH-TO-OPEN

TOP VIEW

6” 6”

11” 11”

PIVOTARM

1/2”

HINGE POST

CENTER OF

HINGE

HINGE POST HINGE POST

CENTER LINE OF

ATTACHMENT POINT

FOR GATE BRACKET

CENTER OF HINGE

GATE CLOSED

DIRECTION OF OPENING

LEFT SIDE VERTICAL VIEW

CAUTION

Never weld parts to the gate or posts when the control board

is powered to avoid irrepairable damage to the circuit board!

NOTICE

Welding is much

preferred, but Nice

offers an optional

bolt-on pivot arm

(P/N 446) for when

welding is not

possible.

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

2MOUNT ACTUATOR TO PIVOT ARM

FIG-2A: INSTALLING ACTUATOR TO PIVOT ARM

FIG-2B: LEVEL ACTUATOR

(GATE OPEN)

FIG-2C: LEVEL ACTUATOR

(GATE CLOSED)

1. Mount actuator to pivot arm as shown in FIG-2A using 1/2” bolt and lock nut. Tighten until secure.

2. Use bubble level to ensure actuator is level and plumb in both open and closed positions.

1/2”x 3.5” BOLT

ACTUATOR

1/2”LOCK NUT

PIVOTARM

CABLE LOOP

LEVEL

ACTUATOR

IMPORTANT!

’When using a bubble level to ensure pivot arm/

actuator are plumb and level, check in both open

and close positions per FIG-2B and 2C.

’Ensure that actuator mounting hardware is tight

enough to prevent movement, vibration, wobble,

or shifting when the actuator is in operation.

’Note cable loop (FIG-2C) to allow strain relief for

cable during actuator0 movement.

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

AFFIX GATE BRACKET TO ACTUATOR ARM

1/2”x 2” PIVOT BOLT

GATE BRACKET

(SIDE VIEW)

GATE BRACKET

ACTUATOR

ARM

1/2” LOCK NUT

WASHER (ZINC)

ACTUATOR

ARM

FIG-3A: AFFIXING GATE BRACKET TO ACTUATOR ARM

FIG-3B: GATE BRACKET HARDWARE REQUIREMENTS

WASHER

(STAINLESS STEEL)

LOCK NUT

If the gate bracket is not already installed on the actuator arm, mount gate bracket to actuator arm with the

pivot bolt, nut, and washers per images below.

WASHER

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

1. Place gate in:

a) CLOSED position for PUSH-TO-OPEN congurations (FIG-4A).

b) OPEN position for PULL-TO-OPEN conguration (FIG-4B).

2. With actuator arm fully retracted, rotate entire actuator on the pivot arm around until the gate bracket

attached to the actuator is positioned on a supporting structure of gate.

3. Mark position of gate bracket on gate or clamp into position.

4POSITION GATE BRACKET ON GATE

GATE OPEN (PULL-TO-OPEN)

FIG-4B: PULL-TO-OPEN GATE BRACKET LOCATION

ACTUATOR

PIVOT

ARM GATE BRACKET

LOCATION

TRAFFIC DIRECTION

ARMATURE FULLY

RETRACTED

WALL

HINGE

POST

FIG-4A: PUSH-TO-OPEN GATE BRACKET LOCATION

GATE CLOSED (PUSH-TO-OPEN)

GATE BRACKET

LOCATION

TRAFFIC

DIRECTION

ARMATURE FULLY

RETRACTED

WALL

HINGE

POST HINGE

PIVOTARM

ACTUATOR

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

TITAN 912L Linear Actuator

Installation Reference Manual

1010

1. Weld the gate bracket to the gate supporting structure (FIG-5A) or use supplied 3/8” bolts and

nuts from kit (FIG-5B).

2. If welding is not possible, drill two holes to match bracket mounting holes and afx with two

3/8”x2.5” screws and 3/8” nuts included in the kit (FIG-5B).

FIG-5A: GATE BRACKET WELDED TO GATE

FIG-5B: GATE BRACKET AND HARDWARE (BLACK BRACKET SHOWN)

5AFFIX GATE BRACKET TO GATE

GATE BRACKET

3/8”x2.5” HEX BOLT (x2)

WELD

3/8” NUT (x2)

IMPORTANT!

Ensure bracket centerline is 1/2” above the top of the pivot arm.

IMPORTANT!

Use a bubble level to assure after mounting that actuator is level and plumb.

CAUTION

Never weld parts to the gate or posts when the control board

is powered to avoid irrepairable damage to the circuit board!

NOTICE

Attach gate bracklet

only to structural

supports. If unsure of

exact bracket location,

tack weld or clamp until

gate can be tested.

www.ApolloGateOpeners.com | (800) 878-7829 | [email protected]

Otros manuales para Titan 912L

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Nice

Nice

Nice Apollo 816 LA Manual de instalación y funcionamiento

Nice

Nice Patio Series Especificaciones técnicas

Nice

Nice Mercury 310 Manual de usuario

Nice

Nice 1551 Manual de usuario

Nice

Nice ROX600 Especificaciones técnicas

Nice

Nice UST1K-1.1kW Guía de inicio rápido

Nice

Nice PLUTO PL 4000 Manual del instalador

Nice

Nice TITAN12L Manual de usuario

Nice

Nice GEFEN GF-AVIP-MC Manual de usuario

Nice

Nice Mercury 310 Manual de instrucciones

Nice

Nice Elero ExitSafe 28 388.0001 Manual de usuario

Nice

Nice HySecurity 1500 Series Manual de instalación y funcionamiento

Nice

Nice METRO ME 3000 Manual de usuario

Nice

Nice ROBO PLUS Manual de servicio

Nice

Nice Max Manual del producto

Nice

Nice Robus 600 Manual de lista de piezas

Nice

Nice SPA30 Manual de servicio

Nice

Nice To-Max Manual del producto

Nice

Nice One-Max Manual del producto

Nice

Nice M-BOARD Guía de inicio rápido

Nice

Nice MG3000 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario