Nice HySecurity TITAN 912L Series Manual de instalación y funcionamiento

Installation Reference Manual

IMPORTANT!

These instructions apply only to the 912L actuator.

Control box installation/operation is described in a separate control box manual.

TITAN12L/12L1 912L actuator

912L LA

Vehicular swing gate actuator

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

LIST OF INSTRUCTIONS

INSTRUCTION 1A: INSTALL PIVOT ARM TO GATE (PULL-TO-OPEN) ............. 5

INSTRUCTION 1B: INSTALL PIVOT ARM TO GATE (PUSH-TO-OPEN) ............. 6

INSTRUCTION 2: MOUNT ACTUATOR TO PIVOT ARM ................................... 7

INSTRUCTION 3: AFFIX GATE BRACKET TO ACTUATOR ARM ....................... 8

INSTRUCTION 4: POSITION GATE BACKET ON GATE .................................... 9

INSTRUCTION 5: AFFIX GATE BRACKET TO GATE ......................................... 10

INSTRUCTION 6: OPEN MECHANICAL RELEASE .............................................11

INSTRUCTION 7: MANUALLY SET GATE OPEN/CLOSE LIMITS ..................... 12

INSTRUCTION 8: RUN ACTUATOR CABLE(S) TO CONTROL BOX ..................13

INSTRUCTION 9A, 9B, 9C, 9D: WIRE ACTUATOR TO CONTROIL BOARD ....14

INSTRUCTION 10A, 10B: SETTING ACTUATOR FINE LIMITS ..........................18

INSTRUCTION 11: ACTUATOR CABLE/TERMINAL WIRING ........................... 19

CONTENTS

LIST OF INSTRUCTIONS ......................................................................2

SECTION 1: TITAN 912L ACTUATOR OVERVIEW ............................3

SECTION 1: TOOLS NEEDED FOR INSTALLATION ........................4

SECTION 2: INSTALLATION SAFETY ................................................4

SECTION 3: ACTUATOR - MECHANICAL INSTALLATION .............5

3.1 MANUALLY SET GATE OPEN/CLOSE LIMITS .....................12

3.2 RUN ACTUATOR CABLE(S) TO CONTROL BOX .................13

3.3 936 CONTROL BOARD WIRING: PULL-TO-OPEN ..............14

3.4 936 CONTROL BOARD WIRING: PUSH-TO-OPEN .............15

3.5 1050 CONTROL BOARD WIRING: PULL-TO-OPEN ............16

3.6 1050 CONTROL BOARD WIRING: PUSH-TO-OPEN ...........17

3.7 SETTING ACTUATOR FINE LIMITS .......................................18

3.8 ACTUATOR CABLE REPLACEMENT WIRING ...................... 20

SECTION 4: PART DRAWINGS ........................................................ 21

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

• TITAN 912L-1 = Actuator with 12’ harness

• TITAN 912L-2 = Actuator with 42’ harness

(dual gate only)

PIVOT ARM (P/N 1116)

ACTUATOR BOLT KIT

(P/N 1125)

GATE BRACKET,

BLACK

(P/N 10025215)

TITAN912L ACTUATOR PARTS IDENTIFICATION

PART# DESCRIPTION QTY

912L-1 ACTUATOR WITH 12 FOOT HARNESS 1

912L-2 (DUAL GATE ONLY) ACTUATOR WITH 42 FOOT HARNESS 1

1116 PIVOT ARM 1

10025215 or PD0959A0000 GATE BRACKET (BLACK) 1

1125 ACTUATOR BOLT KIT 1

TITAN912L ACTUATOR SPECIFICATIONS

DRIVE Electromechanical Stainless Steel Screw

GATE LENGTH and WEIGHT MAX. • Up to 600 lb. for 20 foot leaf (272 kg for 6 m)

• Up to 1000 lb for an 8 ft leaf (453 kg for 2.4 m)

OPEN/CLOSE TIME (TO 90°) 14 - 16 seconds (adjustable)

TEMPERATURE RATING -4º to 122º F (-20º to 50º C)

OPERATING VOLTAGE 12VDC

ACTUATOR DIMENSIONS 43(L) x 4(W) x 6.75 inches (D)

[109.2(L) x 10(W) x 17.5 cm (D)]

USER CONTROLS 936 or 1050 control board

LISTED TO UL325 936 & 1050 Control Boards: Usage Class I, II, III, IV

ACTUATOR WEIGHT 19.75 lb (8.96 kg)

Congratulations on selecting a Nice TITAN 912L actuator. With proper selection, system design, installation

and maintenance this operator should provide years of reliable operation. This manual covers ONLY the instal-

lation of the actuator.

IMPORTANT!

For control box installation, wiring, operation, maintenance instructions and all safety information, refer to the

appropriate control box installation manual used for the system:

• CBOX936 (with 936 control board)

• CBOX1050 (with 1050 control board)

• MB1050 (with 1050 control board, integral batteries, and AC-DC power supply)

SECTION 1: TITAN 912L ACTUATOR OVERVIEW

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

• DISCONNECT POWER AT THE CONTROL PANEL BEFORE MAKING ANY ELECTRIC SERVICE POWER

CONNECTIONS.

• BE AWARE OF ALL MOVING PARTS AND AVOID CLOSE PROXIMITY TO ANY PINCH POINTS.

Below is a list of tools necessary for installation of the Titan actuator:

• Welder (for pivot arm) unless optional bolt-on pivot arm (P/N 446) is used.

• Basic hand tools (screwdrivers, wrenches, pliers, etc..)

• Torx 25 tool (for removing actuator cover screws)

• Level (for ensuring pivot arm and actuator are level).

• Framing square (for determining pivot arm location)

• Torch/Chop Saw (for cutting pivot arm)

• Grinder (for sanding Pivot Arm)

IMPORTANT!

• The gate operator installation is NOT a “do-it-yourself” project. Contract a qualied gate ope-

rator installation company to install this system to ensure a safe and reliable installation.

• It is the responsibility of the property owner to ensure the installer is qualied to carry out the

installation in a safe and professional manner.

• Consult local government agencies for up-to-date rules and regulations to satisfy licensing,

codes or regulations that regulate automated gate system design and installation.

• The gate for which the gate operator is intended to be used should itself be installed correctly

so that it is level and plumb and the gate opens easily and evenly.

• Note that Nice swing gate systems are not intended for installation on an incline.

SECTION 2: INSTALLATION SAFETY

SECTION 3: TOOLS NEEDED FOR INSTALLATION

WARNING!

READ ALL SAFETY INFORMATION WHEN INSTALLING A SWING GATE SYSTEM! SEE EITHER

OF THE FOLLOWING MANUALS FOR SAFETY INFORMATION:

• CBOX936 Control Box Installation Manual (with 936 control board)

• CBOX1050 Control Box Installation Manual (with 1050 control board)

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

LEFT SIDE VERTICAL VIEW

IMAGE 1A-1: "PULL TO OPEN" PIVOT ARM INSTALLATION

INSTALL PIVOT ARM TO GATE: PULL-TO-OPEN

1. Securely mount the pivot arm to the hinge post (IMAGE 1A-1).

2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are

taken from the center of pivot of the gate hinge (IMAGE 1A-1).

3. It is strongly recommended to weld the pivot arm to the hinge post.

TOP VIEW

6” 6”

13” 13”

SECTION 4: ACTUATOR - MECHANICAL INSTALLATION

NOTE: Welding

is much preferred

but Nice offers an

optional bolt-on

pivot arm (P/N 446)

for when welding is

not possible.

PIVOT ARM PIVOT ARM

PIVOT ARM

1/2”

HINGE POST

CENTER OF HINGE

CENTER LINE OF

ATTACHMENT POINT

FOR GATE BRACKET

CENTER OF HINGE

GATE CLOSED

DIRECTION OF OPENING

CAUTION!

NEVER WELD PARTS TO THE GATE OR POSTS WHEN THE CONTROL BOARD IS

POWERED TO AVOID IRREPAIRABLE DAMAGE TO THE CIRCUIT BOARD!

HINGE POST HINGE POST

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

IMAGE 1B-1: "PUSH TO OPEN" PIVOT ARM INSTALLATION

1. Securely mount the pivot arm to the hinge post (IMAGE 1B-1).

2. If necessary, cut pivot arm for correct placement of the actuator mounting hole. Measurements are

taken from the center of pivot of the gate hinge (IMAGE 1B-1).

3. It is strongly recommended to weld the pivot arm to the metal post.

INSTALL PIVOT ARM TO GATE: PUSH-TO-OPEN

CAUTION!

NEVER WELD PARTS TO THE GATE OR POSTS WHEN THE CONTROL BOARD IS

POWERED TO AVOID IRREPAIRABLE DAMAGE TO THE CIRCUIT BOARD!

TOP VIEW

6” 6”

11” 11”

PIVOT ARM

1/2”

HINGE POST

CENTER OF HINGE

HINGE POST HINGE POST

CENTER LINE OF

ATTACHMENT POINT

FOR GATE BRACKET

CENTER OF HINGE

GATE CLOSED

DIRECTION OF OPENING

LEFT SIDE VERTICAL VIEW

NOTE: Welding

is much preferred

but Nice offers an

optional bolt-on

pivot arm (P/N 446)

for when welding is

not possible.

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

2MOUNT ACTUATOR TO PIVOT ARM

IMAGE 2-1: INSTALLING ACTUATOR TO PIVOT ARM

IMAGE 2-2: ACUATOR LEVEL

IMAGE 2-3: LEVEL ACTUATOR

(GATE CLOSED)

1. Mount actuator to pivot arm as shown in IMAGE 2-1 using 1/2” bolt and lock nut. Tighten until secure.

2. Use bubble level to ensure actuator is level and plumb in both open and closed positions.

1/2”x 3.5” BOLT

ACTUATOR

1/2”LOCK NUT

PIVOT ARM

CABLE

LOOP

LEVEL

IMPORTANT!

• Use a bubble level to ensure pivot arm and actuator

are plumb and level in open and close positions

(IMAGES 2-2 & 2-3).

• Ensure that actuator mounting hardware is tight

enough to prevent movement, vibration, wobble,

or shifting when the actuator is in operation..

• Note cable loop (IMAGE 2-3) to allow strain relief

for cable during actuator movement.

ACTUATOR

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

AFFIX GATE BRACKET TO ACTUATOR ARM

1/2”x 2” PIVOT BOLT

GATE BRACKET

(SIDE VIEW)

GATE BRACKET

ACTUATOR

ARM

1/2” LOCK NUT

WASHER (ZINC)

ACTUATOR

ARM

IMAGE 3-1: AFFIXING GATE BRACKET TO ACTUATOR ARM

IMAGE 3-2: GATE BRACKET HARDWARE REQUIREMENTS

WASHER

(STAINLESS STEEL)

LOCK NUT

If the gate bracket is not already installed on the actuator arm, mount gate bracket to actuator arm

with the pivot bolt, nut, and washers per images below.

WASHER

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

1. Place gate in:

a) CLOSED position for PUSH-TO-OPEN congurations ( IMAGE 4-1).

b) OPEN position for PULL-TO-OPEN conguration (IMAGE 4-2).

2. With actuator arm fully retracted, rotate entire actuator on the pivot arm around until the gate

bracket attached to the actuator is positioned on a supporting structure of gate.

3. Mark position of gate bracket on gate or clamp into position.

4POSITION GATE BRACKET ON GATE

GATE OPEN (PULL-TO-OPEN)

IMAGE 4-2: PULL-TO-OPEN GATE BRACKET LOCATION

ACTUATOR

PIVOT

ARM

GATE BRACKET

LOCATION

TRAFFIC DIRECTION

ARMATURE FULLY

RETRACTED

WALL

HINGE

POST

IMAGE 4-1: PUSH-TO-OPEN GATE BRACKET LOCATION

GATE CLOSED (PUSH-TO-OPEN)

GATE BRACKET

LOCATION

TRAFFIC

DIRECTION

ARMATURE FULLY RETRACTED

WALL

HINGE

POST HINGE

PIVOT ARM

ACTUATOR

TITAN 912L Actuator

INSTALLATION REFERENCE MANUAL

1. Weld the gate bracket to the gate supporting structure (IMAGE 5-1) or use supplied 3/8” bolts

and nuts from kit (IMAGE 5-2).

2. If welding is not possible, drill two holes to match bracket mounting holes and afx with two

3/8”x2.5” screws and 3/8” nuts included in the kit (IMAGE 5-2). Tighten to

IMAGE 5-1: GATE BRACKET WELDED TO GATE

IMAGE 5-2: GATE BRACKET AND HARDWARE (BLACK BRACKET SHOWN)

5AFFIX GATE BRACKET TO GATE

GATE BRACKET

3/8”x2.5” HEX BOLT (x2)

WELD

3/8” NUT (x2)

IMPORTANT! Ensure bracket centerline is 1/2” above the top of the pivot arm.

IMPORTANT! Use a bubble level to assure after mounting that actuator is level and plumb.

CAUTION!

NEVER WELD PARTS TO THE GATE OR POSTS WHEN THE CONTROL BOARD IS

POWERED TO AVOID IRREPAIRABLE DAMAGE TO THE CIRCUIT BOARD!

NOTE:

Attach gate

bracklet only to

structural supports.

If unsure of exact

bracket location,

tack weld or clamp

until gate can be

tested.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario