Nexxt XPY 500 series Manual de usuario
Nexxt Solutions - IP Camera Centralization Management Software
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
2
1. Package contents
Chapter 1
User manual
Product overview
XPY 500
Built-in wireless antenna
Night vision LEDs
Lens
Light sensor
Built-in microphone
Status indicator light
Mounting base with articulating arm
Camera mount socket
Heat sink
Network port (RJ45)
5V DC in
Audio output
Reset button
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Open the box and make sure all items listed below are included:
• Integrated wireless IP camera
• AC power adaptor
• Quick installation guide
• CD-ROM (IPC monitor client and search application)
• Network cable
• Mounting bracket and hardware
• Wireless antenna (only applicable to 510 and 520)
1 pc
1 pc
1 pc
1 pc
1 pc
1 set
1 pc
1
11
2
3
4
5
6
7
9
10
12
13
8
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
3
2. Product overview
XPY 510
Weatherproof metal casing
Wireless antenna
Night vision LEDs
Lens
Light sensor
Reset button
5V DC in
Network port (RJ45)
1.
2.
3.
4.
5.
6.
7.
8.
4
5
6
4
3. Product overview
XPY 520
Light sensor
Night vision LEDs
Lens
Status indicator light
Built-in microphone
Reset button (on the bottom side of unit)
Audio output
Network port (RJ45)
Wireless antenna jack
Alarm I/O ports
5V DC in
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
910
10
7
11
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
5
4. Basic set up
Connection of the IP Camera to the network
Begin by attaching the mounting bracket and the antenna (if applicable) to the device.
Select a mounting position on a wall or ceiling.
Use the screws and wall plugs supplied to fix the mounting base.
Insert the Ethernet cable to the RJ45 interface of the IP camera.
Connect the other end of the network cable to your Ethernet switch, hub or router.
Plug the camera to the wall outlet using the supplied AC adaptor to turn it on.
Warning: Make sure to use the supplied power adapter for making the connections to the
AC mains. The use of a different adaptor may cause damage to the camera, heat up or
catch re. Any damage caused to the camera by using the incorrect power adaptor will
void the warranty.
Verify that the mains voltage (110V or 220V) and frequency (50 or 60 Hz) of your
location match those specified on the label.
1.
2.
3.
4.
5.
6.
Computer
Modem
IP Camera
Cellular
Phone
PDA
Internet connection
Intranet
INTERNET
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
6
5. Getting started
System login
A. Installation in a network with the same address range (plug and play mode)
B.Installation in a network with a different address range (manual setup)
In order to be able to see the camera and congure it, you must rst ensure that the IP
camera is within your network address range.
Note: Nexxt Solutions routers are configured within such parameters.
This means that if your internal network is congured with an IP address using
192.168.0.XXX with subnet mask 255.255.255.0, you will be able to access the camera
directly by entering the default IP address into your web browser (Internet Explorer is the
recommended browser).
Access the camera using the web interface by typing the device IP address:
192.168.0.239, and then hit enter.
If your internal network is congured based on a different IP address range, you must
change the IP address of the camera to match your network range. In that case, use the
BSearch_en.exe tool located on the supplied CD or on our Nexxt Solutions website.
Next, open BSearch_en.exe tool and click on the Search option located near the lower-left
corner of the screen, or simply press F3 on your keyboard.
Under Local PC information, you will nd your PC’s network parameters.
Under Device information, you will nd the default values of the IP camera.
Under Device list, you will nd all the IP cameras detected on your network.
In the example below, you will notice a PC connected to an internal network which is using
an IP address of 192.168.1.14, a Subnet mask of 255.255.255.0, plus a Gateway and
a DNS1 of 192.168.1.1.
When done, skip to Step 13 to continue.
1.
2.
3.
1.
2.
3.
4.
5.
6.
4.
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
7
In order for you to access the camera successfully in this scenario, the user
change the IP address, Subnet mask, Gateway and DNS to match the network
parameters of the local PC information or network.
Under Device information, change the IP address to 192.168.1.239, the Subnet
mask to 255.255.255.0 and the Gateway and DNS, to 192.168.1.1.
Note: the IP address must fall within your network range, but outside your DHCP
pool to avoid any IP address conicts on your network. To view or change the Start
and End DHCP address range on your
network, refer to your router’s user manual for instructions.
Next, enter admin under Viewing Account and Viewing Password fields. Once
done, you may click the Update button or press F5 on directly in your keyboard.
The tool will ask you to conrm the changes. Select Yes once prompted.
7.
8.
9.
10.
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
8
A notication that the camera has updated the values successfully will be displayed. The
camera will be restarted as soon as you click OK on the message window, as shown below.
11.
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
9
Once the camera has completely restarted, you can verify the values to ensure they
are congured correctly. Click on Search or press F3 on your keyboard, in order to
select the camera you have just programmed from the Device list. If all values con-
tained in the Device information section are accurate, click on Browse or press F4
on your keyboard to access the camera directly using Internet Explorer.
In this step, the Log in window will appear on the screen. By default, the administra-
tor’s username and the password is admin. When done, click OK to continue.
NOTE: An alternate configuration method is accomplished using the Set IP automati-
cally option, under the IP config menu. If you choose this option, your router will
assign an IP address automatically using its DHCP address range pool. This type of
conguration is normally not recommended, since the IP address will change every
time the lease time has expired for that specic address under the DHCP server.
This means you must use the search tool every time to determine the new IP
address once expired.
12.
13.
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
10
Main User Interface (as seen in Internet Explorer)
Once the main login interface appears, click on Sign in right below the ActiveX Mode
(For IE Browser) option.
The main user interface provides access to controls and the conguration parameters
of the camera based on the privileges assigned to each particular user. (Please refer
to Section 7 - Camera web interface for a brief overview of the controls available.
For detailed instructions refer to the user manual).
6. Wireless Setup for Xpy500, Xpy510 and Xpy520
14.
Once you log into the camera from previous steps, click on For Administrator option.1.
Nexxt Solutions - IP Cameras XPY 500-510-520 Series
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cámara IP de Nexxt
