NEXTTEQ IR Link Manual de usuario

IR Communication Device

Exclusive Nextteq®International Product

Nextteq®IR Link

Instruction Manual

2Designed, built and supported by industry professionals for industry professionals.

Nextteq®IR-Link - a lightweight and

convenient communication tool. Comes

complete with a USB cable. The IR-Link

works with dedicated Nextteq®software to

communicate with Nextteq’s NXS series or NXM

series gas detectors.

The IR-Link can also be used in conjunction with the NXS or NXM

Docking stations. Docking stations utilize a portable USB device

in the ﬁeld; however, when in-house one can use the IR-Link to

directly connect the Docking Station to one’s computer.

Nextteq®International LLC Toll Free: 877-312-2333 www.nextteq.com [email protected]

TABLE OF CONTENTS

I. INTRODUCTION.................................................................................4

II. SOFTWARE INSTALLATION............................................................... 6

A. To Download the Software: ........................................................ 6

B. To Install the Software:................................................................6

III. OPERATION AND USER INTERFACE...................................................8

A. Connect the IR Link Hardware to the Computer...........................9

B. Launch the Software................................................................... 9

C. Open the IR Link COM Port............................................................10

D. Read a Nextteq Portable Gas Detector..............................................11

IV. PORTABLE GAS DETECTOR CONFIGURATION.................................13

A. NXS Interface............................................................................13

B. NXM Interface...........................................................................23

C. Write the New Conﬁguration to the NXS monitor......................28

D. Save a Conﬁguration to File...................................................... 28

V. PORTABLE GAS DETECTOR CALIBRATION......................................28

A. Zero Calibration.........................................................................29

B. Span Calibration........................................................................33

VI. FIRMWARE UPGRADE.....................................................................36

VII. NEXTTEQ PORTABLE GAS DETECTOR LOGS...................................39

A. View Log Data..............................................................................39

B. Erase Log Data.............................................................................40

VIII. SPECIFICATIONS............................................................................. 42

IX. LIMITED WARRANTY.......................................................................43

4Designed, built and supported by industry professionals for industry professionals.

I. INTRODUCTION

The IR Link is a device for communicating with the NXS Single Gas

Detector and the NXM Multi-Gas Detector. It uses dedicated software

provided by Nextteq®to communicate with the monitor.

NXS series - single gas disposable

detectors protect workers from O2

deﬁciency or the following toxic

gases: H2S, CO, SO2 NH3, H2,

or NO2

NXS Single Gas Detector NXM Multi-Gas Detector

NXM series - multi-gas detector detects

CO, H2S, O2 and Combustible Gases (LEL)

Note: LEL is available with a Pellistor or

Infrared sensor

Nextteq®International LLC Toll Free: 877-312-2333 www.nextteq.com [email protected]

One can maintain all important event logs that demonstrate

users are working within company requirements. You can obtain

the following key data:

Each alarm event (30 events) records the following event details:

• Date

• Time

• Duration of Alarm

• Sensor Readings

• Alarm Type

Each event log also captures the following detector information:

• Product Name

• Serial Number

• Log Type

• Firmware version

• Alarm setpoints

• Life remaining

• Total number of events

• Duration of events

• Zero Calibration date

• Span Calibration date

6Designed, built and supported by industry professionals for industry professionals.

II. SOFTWARE INSTALLATION

A. To Download the Software:

1. Download the IR Link application from https://www.nextteqnews.

com/product-support

2. When presented with the option to save or run the ﬁle, choose

Save.

3. Save the installer to a folder where you will be able to ﬁnd it when

the download is ﬁnished. Your Downloads folder or the Desktop

are common options.

4. When the download is complete, the software is ready to be

installed.

B. To Install the Software:

IMPORTANT: At certain points during the installation procedure,

Windows may ask to allow the software to make changes to the

computer. Click Yes for these messages.

1. Locate the installer that was downloaded and double-click the icon

to begin installation.

NOTE: You may receive a security warning about installing the

software; click Run or Run Anyway.

2. The Nextteq®Link Setup Wizard will start. Click Next.

Nextteq®International LLC Toll Free: 877-312-2333 www.nextteq.com [email protected]

3. When the Select Installation Folder window displays, we

recommend that you accept the default location unless instructed

differently by your system administrator. Click Next to use the

default location. To change the installation folder, click Browse and

choose the location you want.

4. The Begin Installation screen displays. Click Install.

5. At this point, the system may need to install Microsoft Visual C++.

These are ﬁles that help the Nextteq®Link software run.

NOTE: If you already have these ﬁles installed on your system, the

installation will skip to Step 8.

Check the box labeled “I agree to the license terms and conditions”

and click Install.

8Designed, built and supported by industry professionals for industry professionals.

6. You may receive a security warning. Click Yes to continue.

7. When the Microsoft Visual C++ installation is ﬁnished, the Setup

Successful window displays. Click Close.

The rest of the installation process continues. You may receive

another security warning. Click Yes to continue.

8. When the installation is ﬁnished, you will see “Click Finish to exit

the Setup Wizard.” Click Finish.

9. The software is ready to use.

III. OPERATION AND USER INTERFACE

WARNING: Do not conﬁgure your IR Link in a hazardous environment.

The Nextteq®IR Link is not intrinsically safe.

Nextteq®International LLC Toll Free: 877-312-2333 www.nextteq.com [email protected]

A. Connect the IR Link Hardware to

the Computer

1. Connect the large end of the included cable

to a USB port on the computer.

2. Connect the small end of the cable to the

IR Link hardware.

3. The computer detects your hardware and

sets it up for use.

NOTE: If you see a message that your computer can’t ﬁnd the drivers for

your hardware, please follow the instructions in CONNECTION above.

B. Launch the Software

1. Find the IR Link PC icon/launcher in the Start menu under Nextteq®

folder. Click the Icon.

2. If Windows asks whether you want to allow the software to make

changes to the device, click Yes.

3. The software launches. After a moment, the software interface is

displayed.

10 Designed, built and supported by industry professionals for industry professionals.

C. Open the IR Link COM Port

When the IR Link software is ﬁrst opened, all ﬁelds will be grayed out

as shown in the above image.

Click the OPEN button to open communication between the IR Link

and the computer. Once communication is established, the IR Link

automatically begins scanning for an available NXS or NXM monitor.

If the IR Link is not found, a “fail Port open” alert pops up. Check to

make sure all cables are connected correctly.

If the NXS or NXM monitor is not found, the “Send TimeOut” alert

pops up. Follow the steps in the next section to read the NXS or

NXM monitor.

NXS Interface

Tabla de contenidos

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario