7.00
3.50
0.00
4.00 12.00 20.00
m
mA
Setting to
Sensor Type :
High Range : 20.00
Low Range : 4.00
High Scale : 7.00m
Low Scale : 0.00m
20.00
12.00
4.00
0.00 3.50 7.00
mA
m
Setting to
High Out Scale : 7.00m
Low Out Scale : 0.00m
Before
510
After
510-10=500
-10
Compensated Value
OUT
Y = X
IN
If X > 0
Y = √{(pv-low scale)
x (high scale-low scale)}
+ low scale
If X <= 0 Y = 0
PV
MODE
O U T
MODE
0 0 0 0
MODE
PV
PV
S E N S
F - S L
.
H - R N
L - R N
H - S C
L - S C
+
TC/RTD
mV / Volt / mA
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODE
MODEMODE
MODE
L I N
0 0 0.0
1 0 0 0
0 0 0 0
MODE
.
.
U N I T
MODE
MODE
M V
℃
5 0 0.0
.
MODE
MODE
0 0 0 0
S - A D
1 0 0 0H - O T
MODE
MODE
MODE
0 0 0 0L - O T
MODE
MODE
A U 4
F I L T
MODE
MODE
.
.
.
PV
MODE
1. display scaling function(mV, Volt, mA only)
This function changes and sets the display value according to scale and input range.
Ex) In case of input range 4.00~20.00mA
and Level 0.00~7.00m
2. Output scaling function
This function can change the 4.00~20.00mA value as the output scale.
Ex) In case of display value 0.00~7.00m,
Output 4.00~20.00mA
3. Sensor compensation function
The function is useful for compensating error by long sensor line or changed zero point by
aged sensor.
Ex) Before sensor adjust
= 510℃ After sensor adjust
= measured value + compensated value
= 510 - 10 = 500℃
4. Function(mV, Volt, mA type only)
Pass the input as it is.
Used for general input type and linearity input.
Pass the input after √. Used for flow rate by orifice.
Like level measuring, when it does not display measuring under zero, it always can
display zero by using limit function.
5.Filter function
Filter is moving average filter and it has 4 kinds of function.
It displays the change of input without filter.
It displays in recent input No 4,8,16 sample average.
Setting filter function delays response.
Do not use filter when high speed response is needed.
When output and display value are changed by irregular input, it is possible to get regular input
and display value by using filter function.
8. Operation and Setting Mode
It is All reset when ship the goods from factory.
If you want initialize all parameter, please reset the instrument.
Push the
at the same time and ON the power.
It is initialized and operation by new setting value.
1.Operation Mode
2. Setting Mode
◉ Make flickering the wanted place by and
setting the value for data setting.
◉ Push the , the figure repeat to 0,1,2…
9,0 and the best position repeat to 0,1,
2…,9,-,-1,0 . If you want to output the
mode,
◉ push the then will go out into the PV
value Mode.
Initialization of the data (All Reset)
◉ Change the setting push at the
same time to move setting mode.
◉ Move to display mode in every mode push
the
◉ DATA setting method
① Setting the decimal point by
② Flickering the purpose digit by
③ Selecting the data by
④ Setting data by pushing the "mode"
⑤ Decimal point can set only the input
range high or input scale high mode.
