NEUTRIK OpticalCON QUAD Manual de usuario

HANDLING INSTRUCTION

opticalCON QUAD Maintenance

www.neutrik.com

BDA 522

QUAD

CAUTION: Laser radiation, do not look directly into beam of light!

Inspection & Dry cleaning (using FOCD-DC125)

Disconnect both cable ends for safety reasons.

Invisible laser radiation may be emitted from

disconnected fibers or connectors. Do not stare into

beams or view directly with optical instruments.

Remove dust cap from the connector (A) and mount

NEUTRIK FOCD-STQ inspection tool on it until it is

locked (B).

Prepare the optical fiber video probe with the

correlate tip (C).

Under the following QR-code you can find a list with

appropriate video probs and tips.

The sealing shutter mechanism of the opticalCON avoids contamination of the LC ferrule locked inside.

The dust-proof design reduces maintenance intervals to a minimum; if nevertheless necessary,

follows the maintenance procedure below to avoid damages on the due to inpropes cleaning.

I HANDLING INSTRUCTION

opticalCON QUAD

1.1

1.2

1.3

optical fiber Microscope

Service tool (FOCD-STQ)

BDA 522

A. Connector Cleaning / Inspection

Intervall: every 500 matings recommended

Tools: Ÿ NEUTRIK QUAD service Tool (FOCD-STQ)

Ÿ Dry Cleaner 1.25 mm (FOCD-DC125)

Ÿ optical fiber video probe

opticalCON

LC tip

opticalCON

During inspection procedure, make sure

that each ferrule is completely free of dust.

As a reference the ferrule has to look as

illustrated on Picture B.

BDA 522

Dry Cleaner 1.25 mm

(FOCD-DC125)

Insert the video probe tool into our NEUTRIK FOCD-

STQ service tool (D).

To inspect the LC ferrule surface focus the video

probe by rotating the focus wheel (E).

Clean the LC surface with the Dry Cleaner 1.25 mm

over the NEUTRIK QUAD service tool.

Push back and forth the dry cleaner to start the

cleaning procedure (F). An endless lint free tape

removes dust particle on the ferrule surface of the LC

connector.

Check the condition of the LC ferrule surface again

and if necessary repeat step 7.

1.4

1.5

1.6

1.7

1.8

Picture A: Picture B:

I HANDLING INSTRUCTION

opticalCON QUAD

opticalCON

After the cleaning procedure unlock the NEUTRIK

inspection tool (G).

Wet cleaning using lint-free wipes

Press forward the twist prevention and untight the

connector bushing and remove carefully the insert of

the connector housing.

Inspect the LC connectors with a video probe tool.

Fold a lint free wipe into a square with one drop of

cleaning fluid. Be sure that a portion of the wipe

remains dry.

Wipe slightly the ferrule tip in the cleaning fluid

moistened portion of the wipe. Immediately repeat

this wiping action on the dry section of the wipe to

remove any residual alcohol.

Dispose the wipe. NEVER REUSE A WIPE.

Inspect the connector again with a video probe tool.

Repeat the process if necessary.

After the cleaning procedure slide the connector

insert back into the connector housing. Align the key

on the insert to the cutout of the metal housing.

Screw both connector parts togehter.

1.9

2.1

2.2

2.3

2.4

2.5

2.6

2.7

2.8

2.9

I HANDLING INSTRUCTION

opticalCON QUAD

4BDA 522

cleaning fluid

FOCD-CFFOCD-DW

- 5 -

www.neutrik.com

NEUTRIK AG LI T: +423 / 237 24 24 F: +423 / 232 53 93

NEUTRIK USA Inc. USA T: +1 704 / 972 3050 F: +1 704 / 438 9202

( )

NEUTRIK UK Ltd. UK T: +44 1983 / 811 441 F: +44 1983 / 811 439

NEUTRIK Vertriebs GmbH DE / NL / AT/DK T: +49 8131 / 280 890 F: +49 8131 / 280 830

NEUTRIK France FR T: +33 1 / 4131 6750 F: +33 1 / 4131 0511

NEUTRIK Tokyo Ltd. JP T: +81 3 / 3663 4733 F: +81 3 / 3663 4796

NEUTRIK Hong Kong Ltd. HK T: +852 / 2687 6055 F: +852 / 2687 6052

NEUTRIK India Pvt. Ltd. IND T: +91 / 982 05 43 424 F: +91 / 22 26163 540

Draft. Nr.: BDA 522 V2 Update: 2020-09-07

I HANDLING INSTRUCTION

opticalCON QUAD

B. Chassis Cleaning

Dry cleaning using FOCD-DC125

Remove Dust cap. Insert the stick of the cleaning

device.

Make sure that the insertion position is on the

bottom of the LC connector hole in order to hit the

sealing shutter release bar.

Push the outer shell to start cleaning the LC

connector end face.

A “pop” sound indicates end of cleaning process.

Remove the cleaning device and put dust cap over

the stick.

Wet cleaning using lint-free wipes

Inspect the LC connectors with a video probe

tool.

Fold a lint free wipe into a square with one drop of

cleaning fluid. Be sure that a portion of the wipe

remains dry.

Wipe slightly the ferrule tip in the cleaning fluid

moistened portion of the wipe. Immediately repeat

this wiping action on the dry section of the wipe to

remove any residual alcohol.

Dispose the wipe. NEVER REUSE A WIPE.

Inspect the connector again with a video probe tool.

Repeat the process if necessary.

1.1

1.2

1.3

1.4

2.1

2.2

2.3

2.4

2.5

2.6

Dry Cleaner

(FOCD-DC125)

Tools: Ÿ Dry Cleaner 1.25 mm (FOCD-DC125)

Ÿ 99% isopropyl alcohol (IPA) or

cleaning fluid (FOCD-CF)

Ÿ Lint free wipes (FOCD-DW)

Ÿ Video probe (CAS-FOCD)

1.1

1.2

QUAD

Find more details of opticalCON

on www.neutrik.com.

cleaning fluid

FOCD-CFFOCD-DW

® ®

Draft. Nr.: BDA 522

www.neutrik.com

Änderungen

# DATUM Versions Nr. Änderung / Beschreibung Auftraggeber

1 2017-05-11 V1

1 2020-09-07 V2 + Wet Cleaning Alexander Mock

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cables y conectores de NEUTRIK

NEUTRIK

NEUTRIK powerCON TRUE1 Guía del producto

NEUTRIK

NEUTRIK NKPH Series Manual de usuario

NEUTRIK

NEUTRIK powerCON TRUE1 TOP Manual de usuario

NEUTRIK

NEUTRIK NP2RX-ULTIMATE Manual de usuario

NEUTRIK

NEUTRIK opticalCON DUO Manual de usuario

NEUTRIK

NEUTRIK NAO4MW-A Manual de usuario

NEUTRIK

NEUTRIK NPPA-TT-SD25 Manual de usuario

NEUTRIK

NEUTRIK powerCON TRUE1 TOP NAC3FX-W-TOP Manual de usuario

NEUTRIK

NEUTRIK etherCON NE8MX-B-1 Manual de usuario

NEUTRIK

NEUTRIK opticalCON DRAGONFLY NKO2SMW-XP Series Manual de usuario

NEUTRIK

NEUTRIK powerCON TRUE1 TOP NAC3FX-W-TOP Guía del usuario

NEUTRIK

NEUTRIK opticalCON Manual de usuario

NEUTRIK

NEUTRIK powerCON TRUE1 NAC3MX-W Guía del producto

NEUTRIK

NEUTRIK NAC3FX-W Guía del producto

NEUTRIK

NEUTRIK powerCON Guía del producto

NEUTRIK

NEUTRIK powerCON TRUE1 TOP Manual de usuario

NEUTRIK

NEUTRIK NC3MX-TOP Manual de usuario

NEUTRIK

NEUTRIK Speakon SPX Series Manual de usuario

NEUTRIK

NEUTRIK opticalCON NO2-4FDW-A Manual de usuario

NEUTRIK

NEUTRIK NP3TT-P Manual de usuario

NEUTRIK

NEUTRIK opticalCON DUO LITE Manual de usuario

NEUTRIK

NEUTRIK Speakon SPX Series Manual de usuario

NEUTRIK

NEUTRIK NE8FDY-C6 Manual de usuario

NEUTRIK

NEUTRIK StageBox Manual de usuario

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario

NEUTRIK opticalCON QUAD Manual de usuario

Manuales populares de Cables y conectores de otras marcas