Network Thermostat NetX X5-CFA Manual

This NetX X5-CFA Operator Menu Guide is a companion to the

NetX X5-CFA Installation Manual. (Part Number #240292) This document will

guide you through the hidden Operator Menu that allows you to congure

settings regular users are not allowed to access.

USING THE MENU

The Dot Matrix Display will provide feedback on the Operator Menu

conguration and selected options. The Up Button Jand Down Button K

are used to select parameters while the LEFT ARROW L(Back Button) and

RIGHT ARROW M(Accept button) are used to accept settings and navigate

through the menu. At any time you can use the CANCEL BUTTON Ito

return to normal operation.

STEP 1 ACCESSING THE HIDDEN OPERATOR MENU

To access the menu, press and hold a hidden button for 5 seconds. The

hidden button is located on the bottom left of the faceplate display. (See

diagram below)

NetX™ X5-CFA

Operator Menu Guide

STEP 2 UNLOCK THE THERMOSTAT

By default, the NetX X5-CFA comes locked from the factory. you can

temporarily bypass the Lock Screen by entering the 4-digit PIN 2697 (‘cows’

on a telephone keypad).

The Dot Matrix area then displays Enter PIN: 0 0 0 0, use the Up Jand Down

KButtons to select the rst digit in the pin code. Press the Accept Button M

(Right Arrow) to Enter the rst digit. Repeat for the next three digits.

After entering the correct PIN, the settings listed below can be adjusted

using the menu. The values are stored by tapping the Accept Button, or by

allowing the display to ‘time out’ by not pressing any buttons for 15 seconds.

The screen will automatically re-lock when you exit the operator menu at the

end or if you press the cancel button while in the menu.

CWARNING: If you enter the incorrect PIN, Wrong PIN will display in the

Dot Matrix display. After 3 wrong attempts, the thermostat will return to the

main screen and will not allow another attempt for 5 minutes.

<–– Turn Over for Settings ––>

Press Here

for 5 Seconds

°F OR °C TEMPERATURE DISPLAY:

Default °F (Fahrenheit) Select between °F (Fahrenheit) or °C (Celsius)

temperature display.

OCC (OCCUPIED) COOL SETPOINT:

Default 73˚F (23˚C) Use the Up Jand Down KButtons to adjust the OCC

Cool Setpoint. The allowable range is 60˚F to 108˚F (16˚C to 42˚C).

OCC (OCCUPIED) HEAT SETPOINT:

Default 69˚F (21˚C) Use the Up Jand Down KButtons to adjust the OCC

Heat Setpoint. The allowable range is 38˚F to 88˚F (4˚C to 31˚C).

UNOCC (UNOCCUPIED) COOL SETPOINT:

Default 80˚F (27˚C) Use the Up Jand Down KButtons to adjust the

UNOCC Cool Setpoint. The allowable range is 60˚F to 108˚F (16˚C to 42˚C).

UNOCC (UNOCCUPIED) HEAT SETPOINT:

Default 60˚F (16˚C) Use the Up Jand Down KButtons to adjust the

UNOCC Heat Setpoint. The allowable range is 38˚F to 88˚F (4˚C to 31˚C).

TEMPERATURE OVERRIDE RANGE (DURING LOCKOUT):

Default: ±3˚F (±1.5˚C) This setting adjusts the temperature variance allowed

from the scheduled setpoint when the faceplate locked. The range is from

±2˚F (±1˚C) to ±5˚F(±2.5˚C).

OVERRIDE TIMER:

Default: 4 Hours Set the amount of time a setpoint override from the normal

schedule is active from 0 hours - 12 hours, in 10-minute increments. At the

end of the override time, the normal schedule will resume. Set to 0 hours to

completely remove setpoint adjustability from the thermostat front panel.

EXIT MENU:

To exit the menu press the right checkmark button M. This will return you to

the Main Thermostat Display.

FACTORY RESET:

While on the Exit Menu Screen, If you press the Up Jarrow, you will see

"Reset to Defaults?" on the dot matrix. Press the right button (accept) to

proceed and you will see " Are you sure?"

To conrm, press the right checkmark button Magain to reset.

CWARNING: This will erase all your Operator Menu Settings and the

Installer Menu Settings and return everything to factory default settings. This

is not reversible.

Otros manuales de Termostato de Network Thermostat

Network Thermostat

Network Thermostat TEC-N2 Series Manual de usuario

Network Thermostat

Network Thermostat NetX X7C-WIFI Instrucciones de montaje

Network Thermostat

Network Thermostat DirectConnect NetX X Series Manual de usuario

Network Thermostat

Network Thermostat NetX X7 Series Instrucciones de instalación y funcionamiento

Network Thermostat

Network Thermostat NetX X Series Instrucciones de montaje

Network Thermostat

Network Thermostat NetX Manual de usuario

Network Thermostat

Network Thermostat GE22-NX Manual de usuario

Network Thermostat

Network Thermostat RP32-NX Especificaciones técnicas

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario