Network Technologies Incorporated SM-X-15V-LC Series Manual de usuario

MAN156 Rev Date 4/26/2017

SM-nXm-15V-LC

Video Matrix Switch

Installation and Operation Manual

VEEMUX®Series

NETWORK

TECHNOLOGIES

INCORPORATED

Tel:330-562-7070

Fax:330-562-1999

1275 Danner Dr

Aurora, OH 44202

www.networktechinc.com

NTI R

TRADEMARK

VEEMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.

in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

FIRMWARE VERSIONS

Firmware Version 1.0

TABLE OF CONTENTS

Introduction....................................................................................................................................................................1

Basic Operation...........................................................................................................................................................1

Supported Web Browsers............................................................................................................................................1

Ordering Information....................................................................................................................................................1

SM-nXm-15V-LC.......................................................................................................................................................1

Materials ......................................................................................................................................................................2

Cables..........................................................................................................................................................................2

Default User Name and Passwords ............................................................................................................................2

Features and Functions................................................................................................................................................3

Installation......................................................................................................................................................................4

To Mount to a Rack .....................................................................................................................................................4

Connect the Sources and Monitors.............................................................................................................................5

Connect RS232 ...........................................................................................................................................................6

Connect to the Ethernet...............................................................................................................................................6

Power Up.....................................................................................................................................................................7

Control Options.............................................................................................................................................................8

Front Panel LCD with Keypad Control.........................................................................................................................8

LCD Menus............................................................................................................................................................9

Save and Load (Recall) Config..............................................................................................................................9

RS232 Control...........................................................................................................................................................10

Remote Connection...................................................................................................................................................10

Baud Rate............................................................................................................................................................10

Unit Address and Loop Back...............................................................................................................................10

Command Protocol.................................................................................................................................................12

Autostatus............................................................................................................................................................13

NTI Switch Control Program For Windows 9X, NT, 2000, XP, Vista and 7 ..............................................................13

SerTest- RS232 Interface Test Program...................................................................................................................14

Main Options...........................................................................................................................................................14

Matrix Operations....................................................................................................................................................14

Ethernet Operations................................................................................................................................................14

Setup Options.........................................................................................................................................................15

Ethernet Control..........................................................................................................................................................16

Telnet Interface-Port 2000.........................................................................................................................................16

Telnet Interface-Port 2005.........................................................................................................................................17

Command Summary...............................................................................................................................................17

Command Detail.....................................................................................................................................................18

RU-Read Unit Size..............................................................................................................................................18

RO-Read Connection for Output Port .................................................................................................................18

CS- Connect Output Port to Input Port................................................................................................................18

CA- Connect All Output Ports to Input Port.........................................................................................................18

SS_01- Enable Auto Status Mode.......................................................................................................................19

SS_00- Disable Auto Status Mode......................................................................................................................19

SX- Examine connections ...................................................................................................................................19

Terminate telnet session .....................................................................................................................................20

Web Interface ............................................................................................................................................................21

Enter the Password ................................................................................................................................................21

Video Switch Page..................................................................................................................................................22

Administration.........................................................................................................................................................24

System Configuration..........................................................................................................................................24

Network Configuration.........................................................................................................................................25

Video Input Names..............................................................................................................................................26

Video Output Names...........................................................................................................................................27

Scanning Sequences...........................................................................................................................................28

Change Password...............................................................................................................................................30

Update Firmware.................................................................................................................................................31

Standby Mode .....................................................................................................................................................32

Logout..................................................................................................................................................................32

iii

Support................................................................................................................................................................33

Reboot.................................................................................................................................................................33

Device Discovery Tool................................................................................................................................................34

Infrared Remote Control.............................................................................................................................................35

Materials ....................................................................................................................................................................35

Buttons.......................................................................................................................................................................36

Operation...................................................................................................................................................................37

Changing Ports.......................................................................................................................................................37

Channel Surfing...................................................................................................................................................37

Jump To Input......................................................................................................................................................38

Jump To Output...................................................................................................................................................38

Connect All ..........................................................................................................................................................38

Save and Recall......................................................................................................................................................38

Multiple Switch Control...........................................................................................................................................39

Canceling a Command...........................................................................................................................................39

Technical Specifications For IRT-UNV......................................................................................................................39

Troubleshooting the IRT-UNV ...................................................................................................................................39

RS232 Connection Cable............................................................................................................................................40

Pinout for Matrix Y-1 Cable........................................................................................................................................40

Specifications..............................................................................................................................................................40

Troubleshooting..........................................................................................................................................................41

Safety Statements .......................................................................................................................................................41

Index.............................................................................................................................................................................41

Warranty Information..................................................................................................................................................42

TABLE OF FIGURES

Figure 1- Secure rack mount ears to switch.......................................................................................................................................4

Figure 2- Secure switch to a rack ......................................................................................................................................................4

Figure 3- Install Video Source Cables................................................................................................................................................5

Figure 4- Connect a monitor to the VEEMUX....................................................................................................................................5

Figure 5- Connect user terminal for RS232 control............................................................................................................................6

Figure 6- Connect the LAN to the VEEMUX......................................................................................................................................6

Figure 7- Connect Power to VEEMUX...............................................................................................................................................7

Figure 8- RS232 connection with Matrix-Y-1 cable..........................................................................................................................11

Figure 9- Pinout of Matrix-Y-1 cable ................................................................................................................................................11

Figure 10- Web interface Login page..............................................................................................................................................21

Figure 11- Main menu and Video Switch page................................................................................................................................22

Figure 12- System Configuration page ............................................................................................................................................24

Figure 13- Network Configuration page...........................................................................................................................................25

Figure 14- Video Input Names page................................................................................................................................................26

Figure 15- Video Output Names page .............................................................................................................................................27

Figure 16- Scanning Sequence page ..............................................................................................................................................28

Figure 17- Change Password page .................................................................................................................................................30

Figure 18- Update Firmware page...................................................................................................................................................31

Figure 19- VEEMUX in Standby Mode.............................................................................................................................................32

Figure 20- Logout of the VEEMUX web interface............................................................................................................................32

Figure 21- Support Tab....................................................................................................................................................................33

Figure 22- System Reboot...............................................................................................................................................................33

Figure 23- Device Discovery Tool page...........................................................................................................................................34

NTI VEEMUX VIDEO MATRIX SWITCH

INTRODUCTION

The SM-nXm-15V-LC (n = number of inputs (video sources), m = number of outputs (monitors)) video matrix switch (VEEMUX)

allows any of up to 8 video sources to output to any or all of up 8 (8) monitors. The configuration of the VEEMUX is determined

at time of order. The bandwidth of the SM-nXm-15V-LC is 160MHz and video resolutions through 1920 x1200 are supported with

no degradation. The switch can be controlled with the Front Panel Keypad, RS232 interface, Ethernet, or an Infrared Remote.

The VEEMUX can be ordered in many sizes and with several control options. The base unit includes a user keypad, an RS232

port, and an Ethernet port to make up a complete system. Built-in infrared control allows for maximum user satisfaction in each

unique configuration.

Basic Operation

The VEEMUX allows any source to be connected to any destination at any time with no restrictions or limitations.

Video inputs accept any RGBHV, RGBS, or RGsB signal.

Video outputs are compatible with any RGBHV or RGBS monitor, regardless of input. (RGsB monitor requires

RGsB input)

Supported Web Browsers

Most modern web browsers should be supported. The following browsers have been tested:

Microsoft Internet Explorer 6.0 or higher

Netscape 7.0 or higher

Mozilla FireFox 0.9.2 or higher

Set your browser to always check if there is a newer version of the page than the version stored in cache. This action will ensure

that it will display the most up-to-date information.

Ordering Information

The SM-nXm-15V-LC is built to a specific size ranging from 2, 4 or 8 monitors and 4 to 8 video sources. The “n” in the part

number represents the number of video sources. Select a switch built for 4 or 8 video sources. The “m” in the part number

represents the number of outputs (monitors). A switch built for 2, 4 or 8 monitors may be ordered. It is not necessary to fully

populate all of the connectors on the unit (ex. an SM-8x8 switch has the capability of supporting 8 video sources and 8 monitors,

but it will operate with only 4 video sources with 2 monitors connected.

SM-nXm-15V-LC

Replace the “n” with 4 or 8

Replace the “m” with either 2, 4 or 8

The following list represents the available sizes that can be ordered:

SM-4x2-15V-LC SM-8x2-15V-LC

SM-4x4-15V-LC SM-8x4-15V-LC

SM-8x8-15V-LC

NTI VEEMUX VIDEO MATRIX SWITCH

Materials

Materials Supplied with this kit:

NTI SM-nXm-15V-LC Video Matrix switch

IEC Line cord, country specific

Infrared Remote Control with 2-AAA batteries

CT6182 DB9 Female-to-RJ45 Female adapter

CB5021- 5 foot CAT5e-SF-5-Gray patch cable

4-#10-32 x 3/4" pan head screws and 10-32 cagenuts (server cabinet mounting hardware)

Rack Ear Kit including 2 Rack Ears and 6-#6-32 X 3/16” screws

Cables

All cables are sold separately. The following tables list the available stocked cables with their length in feet. All VGA input and

output connectors on Matrix Switches are FEMALE. When using multi-coax high resolution VGA to BNC cables, the BNC

connectors are also FEMALE for input and output. Custom cables are available – contact NTI for pricing and distance / resolution

limitations.

NTI NAME DESCRIPTION

VGA

VEXT-3/6/10/15/25/35/50/75/100-MM

VEXT-3/6/10/15/25/35/50/75/100

VINT-5B-6

Multi-coax high resolution VGA or SVGA video cable. Connectors are 15HD male-male

(used for INPUTS)- 3 thru 100 feet

Multi-coax high resolution VGA or SVGA video cable. Connectors are 15HD male-

female (used for OUTPUTS)-3 thru 100 feet

Multi-coax high resolution VGA to BNC cable. Connectors are 15HD male to 5 BNC’s-6

feet long RS232

Matrix-Y-1 or see page 31 for

alternative cables RS232 Interface Cable- Connectors are 9D male- female-female 12" long

CT6182 RJ45F-DB9M Adapter

Contact NTI for various lengths and

colors Cat5 UTP Cable- Connectors are RJ45 male-Stocked cables are 2 thru 100 feet

Custom cables must have RJ45 connectors wired straight thru- pin 1 to pin 1, etc.

ETHERNET

Contact NTI for various lengths and

colors Cat5 UTP Cable- Connectors are RJ45 male-Stocked cables are 2 thru 100 feet

Custom cables must have RJ45 connectors wired straight thru- pin 1 to pin 1, etc.

Default User Name and Passwords

The default Telnet password is nti (lower case letters only) . For instruction on using Telnet, see page 16.

(No username is required in order to use Telnet. You will only be prompted for a password.)

The default Web Interface user name is root (lower case letters only).

The default Web Interface password is nti (lower case letters only). For instruction on using the Web Interface,

see page 21.

NTI VEEMUX VIDEO MATRIX SWITCH

FEATURES AND FUNCTIONS

# LABEL CONNECTOR/LED DESCRIPTION

1 Menu Buttons Buttons for navigating LCD menu

2 None LCD Display Displays port connections and menu for control of the VEEMUX

3 PWR Green/Red LED Illuminates green to indicate proper power to the unit and normal

operation

Illuminates red during system boot-up or while in standby

4 IR In Sensor Receives communication from hand-held remote control

5 IR Activity Green LED Illuminates to indicate communication between the hand-held remote

control and the VEEMUX

6 AC INPUT IEC Connector For attachment of the IEC power cord to power the VEEMUX

6a Fuse Fuseholder For replaceable 2A 240VAC Fast-blo Fuse

7 None Power Switch For powering ON and OFF the VEEMUX

8 VIDEO HD15 Female For direct connection of VGA video cable from video source

9 MONITOR HD15 Female For direct connection of VGA video cable from display device

10 ETHERNET RJ45 Female For connection to an Ethernet for remote multi-user control

11 RS232 RJ45 Female For connection of a PC for serial control

12 System Reset Button Press to reset VEEMUX to default settings

NTI VEEMUX VIDEO MATRIX SWITCH

INSTALLATION

To Mount to a Rack

1. Attach the ears to the switch using the #6-32x3/16" flat Phillips-head screws (6) provided as shown in the illustration below.

The holes in the ears should line up with pre-threaded holes in the sides of the NTI switch. Tighten the screws securely.

Figure 1- Secure rack mount ears to switch

2. Install 4 cage nuts (supplied) to the rack in locations that line up with the holes in the mounting ear on the NTI switch.

3. Secure the NTI switch to the rack using four #10-32X3/4” screws (supplied). Each screw should be of sufficient length

to go completely through the NTI mounting ear, rack frame and fully engage all threads in the cage nut. Be sure to

tighten all mounting screws securely.

4. Attach all cables securely to the switch and where necessary supply adequate means of strain relief for cables.

Figure 2- Secure switch to a rack

6-32x3/16"

Flat Head

Screws

(supplied)

Rack mount ear

NTI Switch

Front of Switch

NTI Switch

Rack Screws

#10-32x3/4"

(supplied)

Rack

(supplied)

Cage Nuts

NTI VEEMUX VIDEO MATRIX SWITCH

Connect the Sources and Monitors

1. Turn OFF power to all video sources (inputs) that will be connected to the VEEMUX before connecting or

disconnecting any cables.

2. Connect a VEXT-xx-MM cable from the video port of a video source to a 15HD female video connector

labeled VIDEO 1 on the VEEMUX. (See Fig. 1)

3. Connect additional video sources to remaining 15HD female VIDEO x connectors as desired.

Figure 3- Install Video Source Cables

4. Connect a monitor to the 15HD female connector labeled MONITOR 1 on the rear of the VEEMUX (See Fig. 2).

5. Connect additional monitors to remaining 15HD female MONITOR x connectors as desired.

Figure 4- Connect a monitor to the VEEMUX

NTI VEEMUX VIDEO MATRIX SWITCH

Connect RS232

RS232 control can be achieved using a separate user terminal or CPU with a terminal program. To make a terminal connection, a

DB9M-to-RJ45F adapter and 5 foot CAT5 patch cable have been supplied if needed.

Figure 5- Connect user terminal for RS232 control

Connect to the Ethernet

If the Telnet Interface (page 16) or Web Interface (page 21) will be used, an Ethernet connection to the Local Area Network (LAN)

must be made using CAT 5 cable with RJ45 connectors. Wiring between the connectors should be straight through (pin 1 to pin

1, pin 2 to pin 2, etc.) Connect a CAT 5 cable between the connector label "ETHERNET" and the LAN (see Fig. 4).

Figure 6- Connect the LAN to the VEEMUX

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Conmutador de matriz de Network Technologies Incorporated

Network Technologies Incorporated

Network Technologies Incorporated VEEMUX Series Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

Kramer

Kramer XL 3216VS Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer Sierra Video 6432V5xl Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Kramer

Kramer LASSEN XL 3232S Manual de usuario

Roland

Roland XS-1HD Manual de usuario

Kramer

Kramer VS-66HDCPxl Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas