Network Electronics Flashlink ETH1000-D Manual de usuario
network-electronics.com
Gigabit Ethernet Media Converter
with DWDM laser
Rev. 1
Flashlink User Manual
ETH1000-D
ETH1000-D Rev. 1
Network Electronics AS
P.O. Box 1020
N-3204 Sandefjord, Norway
Phone: +47 33 48 99 99
Fax: +47 33 48 99 98
Email: [email protected]
www.network-electronics.com
Support Phone: +47 90 60 99 99
Revision history
Current revision of this document is the uppermost in the table below.
Rev. Repl. Date Sign Change description
1 0 2008-07-24 AS Added Declaration of Conformity
0 A 2007-09-11 GMW First version
network-electronics.com | 2
ETH1000-D Rev. 1
Contents
Revision history .......................................................................................................... 2
1 Product overview ..................................................................................................... 4
2 Specifications .......................................................................................................... 5
2.1 Optical Characteristics .......................................................................................................5
2.2 Ethernet..............................................................................................................................5
2.3 General...............................................................................................................................5
3 Configuration ........................................................................................................... 6
3.1 DIP control..........................................................................................................................6
3.2 GYDA-SC control ...............................................................................................................7
3.2.1 Block descriptions ...........................................................................................................7
4 Connector module ................................................................................................... 8
4.1 Mounting the connector module .........................................................................................8
4.2 Terminal format support .....................................................................................................9
5 Module status ........................................................................................................ 10
5.1 Front panel – Status monitoring .......................................................................................10
5.2 GPI Alarm – Module status outputs..................................................................................11
6 Laser safety precautions........................................................................................ 12
General environmental requirements for Network Electronics equipment ................ 13
Product Warranty...................................................................................................... 14
Appendix A Materials declaration and recycling information..................................... 15
A.1 Materials declaration........................................................................................................15
A.2 Recycling information.......................................................................................................15
EC Declaration of Conformity ................................................................................... 16
network-electronics.com | 3
ETH1000-D Rev. 1
1 Product overview
The Flashlink ETH1000-D is a 10/100/1000Base-T to 1000Base-X converter module. The
module converts a 10/100/1000Mbps Ethernet signal on copper to 1000Mbps fibre suitable
for long haul applications. The module has one electrical Ethernet port, and one fibre
transceiver port (receiver fibre connector and transmit fibre connector). The speed on the
electrical connector is dependent of the DIP switch setting or GYDA control. Speed will upon
link connection automatically be set at the highest possible speed. User can independently
enable or disable 10Mbps, 100Mbps or 1000Mbps. The fibre link can be used in one or two
fibre installations, or occupy two wavelengths in a WDM, CWDM or DWDM installation.
network-electronics.com | 4
ETH1000-D Rev. 1
2 Specifications
2.1 Optical Characteristics
Optical input
Transmission circuit fibre: 9/125um Single Mode
Sensitivity Better than –25dBm
Optical wavelength 1200nm – 1610nm
Detector damage threshold > +1dBm
Max input power 0dBm
Connector SC/UPC
Optical Output
Transmission circuit fibre 9/125um Single Mode
Light source DFB DWDM Laser
Optical wavelength 1530.33nm - 1561.41nm, 40 C-band DWDM channels acc. to
ITU-T G.694.1
Channel spacing 100GHz
Power output 0dBm (+5dBm for high power version)
Extinction ratio > 10:1
2.2 Ethernet
10BaseT/100BaseTx/1000BaseT on RJ-45 connectors. Compliant with IEEE 802.3, IEEE
802.3u, IEEE 802.3ab and IEEE 802.3z. Auto speed sensing and MDI/MDI-X.
2.3 General
Power +5V DC/2.5W and +15V DC / 0.5W
Control Control system for access to setup and module status with
BITE (Built-In Test Equipment)
network-electronics.com | 5
ETH1000-D Rev. 1
3 Configuration
ETH1000-D can be configured by DIP or from Flashlink GYDA-SC.
3.1 DIP control
The tables below explain the functionality of the dipswitches.
# Description
1. Enable 10Base-T
2. Enable 100Base-T
3. Enable 1000Base-T
4. Auto- negotiation on 1000Base-X
5. Reserved
6. Reserved
7. Reserved
8. GYDA override/DIP
When DIP switch 1, 2 and 3 are all on or off, speed is set to auto.
DIP switch 1 enables/disables 10Base-T electrical connection.
DIP switch 2 enables/disables 100Base-T electrical connection.
DIP switch 3 enables/disables 1000Base-T electrical connection.
DIP switch 4 enables/disables auto-negotiation on the optical connection, 1000Base-X.
When connecting ETH1000-D to ETH1000MC, auto-negotiation must be disabled. Using two
ETH1000-Ds, these DIPs must be in the same situation.
Dip 5, 6 and 7 are reserved.
network-electronics.com | 6
ETH1000-D Rev. 1
Dip 8 sets if GYDA-SC is able to configure or not. When GYDA-SC override is set, the actual
setting can be read by using the info command (se GYDA-SC user manual for details).
3.2 GYDA-SC control
Latest configuration from GYDA-SC is stored local on card. This prevents configuration loss
during power recycling.
The card supports Flashlink protocol v4.0.
3.2.1 Block descriptions
Supported block command.
3.2.1.1 Laser
<identifier> ::= 'lsr'
<status> ::= 'D' [<wavelength>'nm'] [<power>'dBm'] ['on'|'off'] ['ok|fail'] ['tempfail'|'stab']
<block command> ::= <operation>
<operation> ::= 'on'|'off'
3.2.1.2 PIN
<identifier> ::= 'pin'
<status> ::= ['cd'|'ncd']
3.2.1.3 Voltage
<identifier> ::= 'pwr'
<status> ::= [<nominal voltage>'Vnom'] [<voltage>]
3.2.1.4 General output
<identifier> ::= 'gpi'
<status> ::= ['out'] ['act'|'inact'] ['thru'] ['id' '"'<GPI identifier>'"']
<block command> ::= <set state>
<set state> ::= 'act'|'inact'|'thru'
3.2.1.5 Ethernet port
<identifier> ::= 'ethp'
<status> ::= ['dis'|'en'] ['cd'|'ncd'] [('10'|'100'|'1000') ('man'|'auto')] [('full'|'half') ('auto')]
[('mdi|mdix') ('auto')] [('mas'|'sla') ('auto')]
<block command> ::= 'dis'|'en'| <speed mode>
<speed mode> ::= 'speed' '10'|'100'|'1000'|'auto'
3.2.1.6 Misc
<identifier> ::= 'misc'
<status> ::= ['prog'|'fin'] ['ovr']
network-electronics.com | 7
ETH1000-D Rev. 1
4 Connector module
The ETH1000D has a dedicated connector module: ETH1000-C1. This module is mounted at
the rear of the sub-rack. The module is shown in the figure below.
OPT TX
GPI
OPT RX
10/100/1000Base-T
4.1 Mounting the connector module
The details of how the connector module is mounted, is found in the user manual for the sub-
rack frame FR-2RU-10-2.
This manual is also available from our web site:
http://www.network-electronics.com/.
network-electronics.com | 8
ETH1000-D Rev. 1
4.2 Terminal format support
The different input and output ports on ETH1000D can support a number of formats. The
table below shows the input and output signals on the back plane.
Terminal format support:
Terminal Function Supported Format Mode
OPT RX Optical input 1000Base-X Input
OPT TX Optical output 1000Base-X Output
1000Base-T Electrical input 10/100/1000Base-T In/output
GPI ALARM Open Collector
Alarms
Wired alarms OC Output
network-electronics.com | 9
ETH1000-D Rev. 1
5 Module status
The status of the module can be monitored in three ways.
1. GYDA-SC System Controller (optional).
2. GPI at the rear of the sub-rack.
3. LED’s at the front of the sub-rack.
Of these three, the GPI and the LED’s are mounted on the module itself, whereas the GYDA
System Controller is a separate module giving detailed information on the card status. The
functions of the GPI and the LED’s are described in sections 5.2 and 5.1. GYDA-SC is
described in a separate user manual
5.1 Front panel – Status monitoring
The status of the module can be easily monitored visually by the LED’s at the front of the
module. The LED’s are visible through the front panel as shown in the figure below.
STATUS
LOS
LINK
ACT
Figure 7: Front panel indicators for the ETH-1000-D.
ETH-1000D has 4 LED’s each showing a status corresponding to the GPI pinning.
Diode \ State Red LED Green LED Orange LED No light
Status Module is faulty,
or module is
initializing.
Module is OK
Module power is
OK
Laser off Module has no
power
LOS No optical signal Optical signal Module has no
power
LINK No
10/100/1000Base-
T link
10/100/1000Base-
T link
No link
ACT Ethernet traffic No Ethernet trafic
network-electronics.com | 10
Tabla de contenidos
Otros manuales de Convertidor de medios de Network Electronics
Network Electronics
Network Electronics SDI-EO-D15 Series Manual de usuario
Network Electronics
Network Electronics Flashlink HD-OE-2 Manual de usuario
Network Electronics
Network Electronics ADC-SDI-CC Manual de usuario
Network Electronics
Network Electronics Flashlink SDI-EO-2 Manual de usuario
Network Electronics
Network Electronics HD-EO Manual de usuario
Network Electronics
Network Electronics ADC-SDI Manual de usuario
Network Electronics
Network Electronics Flashlink ETH1000MC Manual de usuario
Network Electronics
Network Electronics Flashlink HD-EO-2 Manual de usuario
Network Electronics
Network Electronics Flashlink ETH100 Manual de usuario
