NETVIO MX-HT2-0808-10 V4 Manual de usuario
USER
GUIDE
MX-HT2-0808-10 V4
Simplifying
Complexity
AUDIO | VIDEO | DATA | SOFTWARE
INDEX
8x8 Matrix
MX-HT2-0808-10
Drivers available at www.netvio.co.uk
Grab & Go information
Process to success
Safety Information
Warranty
In-the-box
Important installation guidance
System Wiring
Product features
Cable & connector guidelines
Which HDBaseT receiver?
Which HDBaseT receiver? cont.
Front panel
Rear panel
Rear panel continued
IR accessories, wiring & guidelines
Netvio 360 - Setting up your HT2 Matrix
Netvio 360 - Configure end-user control APP
Netvio GO - end user control APP
Specifications
Contact details
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13 & 14
Page 15
Road to success
Read safety information & installation guidelines. Find a safe
home for your matrix device.
Read cabling recommendations & connector termination
requirements. Test cabling before connecting Netvio
devices.
Download the Netvio360 configuration software from
www.netvio.co.uk/download
Connect Netvio device and PC/MAC to the same network.
Download the Netvio GO free AV control application for
each end-user device using the following QR codes.
IP Settings: DHCP (auto assigned without DHCP)
Serial Settings: 115200 Baud, 8n1
Default User Name/Password: admin/password
Factory reset: Press & hold output 2 for 40 seconds (display will confirm)
Network settings reset: Press & hold output 1 for 40 seconds (display will confirm).
Netvio 360 download: www.netvio.co.uk
Netvio GO APP download: www.netvio.co.uk
Product instruction videos: www.netvio.co.uk/matrix/mx-ht2-0808-10
Product Support: [email protected] | Instant Chat | UK (0870) 448 7001
GRAB & GO
Watch the latest instructional videos for the MX-HT2-0808-10 at
www.netvio.co.uk/products/mx-ht2-0808-10
1
Process to success
Premium 8x8 Matrix using Gen. 2 HDBaseT transmission technology
delivering 4K/60 4:4:4 HDR capability over a dedicated single cable
infrastructure or full 18Gbps pure HDMI outputs. The HT2-0808 includes a host
of free-on-board features including onboard scaling, audio distribution &
routing, ARC capture, both 40m & 70m output capabilities as well as
compatibility with Netvio's 360 embedded configuration utility and Netvio GO
end-user full spectrum AV control applications.
Quick Start Guide
Thank you for purchasing this Netvio product. The quick-start-guide is
designed to provide all required information to install your product
successfully, ensuring correct installation standards, therefore guaranteeing
performance in accordance with published features and specifications. Netvio
therefore greatly appreciates your time in reviewing the provided information
and following our recommended guidelines.
MX-HT2-0808-10
Before starting the installation, we recommend that you
download the Netvio 360 utility software from
www.netvio.co.uk. This provides easy configuration of the HT2
matrix. In addition, 360 provides the gateway to the Netvio GO
AV control application for Apple and Android devices. You will
require the product serial & product part number as a part of
the software validation process.
Safety Information
Attempts to remove product casings could result in electrical shock. Please do not attempt
to repair the device. In the event of product service requirements, please contact Netvio Ltd
or an authorised reseller for service procedures. Any unauthorised attempt to repair the
product or attempts to replace components with non-approved parts will invalidate the
product warranty. For full warranty conditions, please visit www.netvio.co.uk
Important Installation Guidelines
Prior to configuration, please ensure the matrix is properly seated on a flat, secure surface or housed in a suitable rack
mount with ample space for airflow and heat dissipation. Avoid direct contact with sources of heat such as heating systems
or audio amplifiers. Operating environment should not exceed stipulations of 0°C / +40°C | 20% - 90% RH
A suitable wired or wireless network with a router supporting DHCP (Dynamic Host Configuration Protocol ) is required
where both Matrix and computer are connected to the same network.
If a suitable router or DHCP server is not available, a direct network connection between computer and Matrix is supported,
with both computer and Matrix set to auto assign IP addresses, where Netvio360 will discover the device and guide you
through the set-up.
Drivers available at www.netvio.co.uk
In the box
1no. Netvio matrix device.
1set Regionalised IEC power lead.
1 Pair of 19" mounting brackets
8no. IR emitters
8no. IR receivers
8no. IR to IR cables
8no. 3-Pin serial connectors
1no. RS-232 connection cable
1no. master remote
3-year standards parts & labour
warranty.
Additional 2-years subject to online
registration within 90-days of
installation.
Safeguard 10-Year | 10% option
available.
Full warranty terms & conditions &
online registration available at
www.netvio.co.uk
Warranty
2
System wiring suggestion
Drivers available at www.netvio.co.uk
3
8x8 HDBaseT multi-functional audio, video, data & control matrix.
Compatible with all latest standards including HDMI2.0b & HDCP2.2.
Supporting latest (18Gb) digital audio & video standards including HDR-10, HLG, Dolby Vision, DTS-X and
Dolby Atmos.
Accepts popular high bandwidth media sources providing seamless adjustments & transport over a
dedicate HDBaseT AV network using Cat5e/6.
Outputs (1-4) support 4K/60 HDR to 40m & 1080p to 70m.
Enhanced outputs (5-8) performance provides 4K/60 HDR support to 70m & 1080p to 100m.
Outputs (5-8) supports 100BaseT data transport over HDBaseT up to 100m.
All outputs support 4K/1080p scaling. Pure HDMI outputs have independent scaling.
ARC capture and routing from all connected display to both analog & digital zoned outputs.
Accepts up to four ‘audio only’ source inputs with ability to distribute, embed and output from any analog
or digital output.
28x16 independent audio matrix with DSP.
All outputs supported by full 18Gb HDMI mirror outputs (with scaling) for local AVRs, more displays or
connectivity to other Netvio devices.
Both direct zone and routed RS-232.
Cost effective SafeGuard enhanced product protection for up to 10-years for 10% additional cost.
Netvio GO - Free full spectrum AV control APP for Apple and Android devices. Supports full API including
independent audio and video switching, volume, media source and display control. Control methods
include bi-directional IR, RS-232, CEC & IP, without the need for additional system hardware.
Netvio 360 – Free cross platform discovery, configure, optimise & design software.
3no. compatible receivers to achieve desired budget and function.
RX-HT2-40-10: All the basics of 4K/60 HDR to 40m, 1080p to 70m. Apply to all outputs for lowest budget
option.
RX-HT2-40-20: Adding ARC capture support to any output.
RX-HT2-70-10: 70m 4K/60 HDR to 70m, ARC capture & 100BaseT Ethernet. Perfect match for enhanced
output (5-8).
Please check functionality of matrix outputs to ensure required features are available.
Product Features
Drivers available at www.netvio.co.uk
4
Advertised cable distances are for guidance only. Many factors can effect transmission
distances including cable construction, quality, install standards, patch panels, faceplates and
external factors such as electromagnetic interference (EMI).
This product is designed to run over unshielded twisted pair Cat5e/6/7 cable. Some
consideration is required when installing shielded (STP) category cable ensuring all drain wires
and shielding are correctly grounded.
All RJ45 terminations should follow EIA/TIA-568-B terminations and not simply wired Pin 1-1,
Pin 2-2.The 568-B standard involves the splitting of the green pair to pins 3 & 6.
Maintain twists within the Cat5e/Cat6/Cat7 cores up to the point of termination.
Maintain gradual bends when installing category cable, ensuring a minimum radius of 25mm
where possible. Avoid sharp bends or twists in the cable avoiding taught or stretched cable at
all times.
When dressing the cable use moderate to low pressure, avoiding pinching of the cable jacket.
Do not splice, join or bridge the cable at anytime, as this will undoubtedly cause transmission
issues.
Use moderate to low pressure when pulling category cable avoiding pressures in excess of
11kgf (of force).
Keep category cable away from sources of EMI (electrical cables, transformers, light fixtures)
ensuring a minimum parallel distance of 300mm, crossing at right angles if absolutely
necessary.
Ensure cable is correctly tested, understanding that a basic continuity check may not be
sufficient to identify issues or to certify cable performance.
Always check local regulations relating to building and fire codes.
Cable & Connector Guidelines
Which HDBaseT Receiver?
Any Netvio receiver will work on any matrix output regardless of supported features. To gain the best performance and to
achieve the most cost effective install, please follow the features described below. Additionally, check the supported
performance of each output, as they can vary. Matching the right extender and output capability will achieve the desired
outcome.
RX-HT2-40-10
Basic receiver supporting 4K/60 HDR | PoC | 2-Way IR | RS-232
Can be used on all matrix outputs to achieve 40m 4K
performance.
24v power-over-cable (PoC) feature means receiver is powered
from the matrix. No PSU required.
Drivers available at www.netvio.co.uk
5
RX-HT2-40-20
Adding ARC capture & routing capability to all matrix outputs.
Can be used on all matrix outputs to achieve 40m 4K performance.
24v power-over-cable (PoC) feature means receiver is powered from the
matrix. No PSU required.
Adding 70m 4K/HDR performance, including ARC capture &
routing. To achieve full functionality, connect to Matrix outputs 5-8.
Includes 100BaseT Ethernet pass-thru for smart TV or wireless
access. To achieve full functionality, connect to Matrix outputs 5-8.
The receiver can be connected to outputs 1-4, but features are
output dependent, so 70m and LAN will not be supported.
24v power-over-cable (PoC) feature means receiver is powered
from the matrix. No PSU required.
RX-HT2-70-10
VIDEO
AUDIO
DATA CONTROL
6
# @ A B C D E
F G H I
Front Panel
#
@
Dual purpose function. In normal operation, it allows you to select output 1, followed by the input selection to
initiate a manual video switch. However if this button is pressed and held for 40s it will reset all network
settings, returning to factory default. The LCD display will provide confirmation of reset.
Output - 1
Output - 2
A
LED display showing status of input/output, current IP settings, RS-232 settings & EDID input status for each
output. Use the MENU button to scroll through options, using arrows to navigate. Use MENU to return to home
position.
Output Selection
BPressing the ALL button, followed by an input selection will send the video source to all connected displays.
All Displays
CStatus Display
DUse the MENU button to scroll through options, using arrows to navigate. Use MENU to return to home position.
Menu Arrows
ERed LED indicates that standby mode is active.
Standby LED
FUse any of the input selection buttons after selecting the required output to initiate a manual video switch.
Input Selection
GOne button press to initiate output 1 to input 1, output 2 to input 2 etc.
Mirror
Dual purpose function. In normal operation, it allows you to select output 2, followed by the input selection to
initiate a manual video switch. However if this button is pressed and held for 40s it will reset all settings,
returning to factory default. The LCD display will provide confirmation of reset.
HArea to focus direct IR commands
IR receiving window
IPress & hold for 3 seconds to put matrix into standby mode. Short press to wake Matrix.
Power standby button
Use any of the output numbers to select a display, followed by a video input button below, to initiate a manual
video switch.
7
C E F G H I J K L
A B D
A
B
Provides overall basic control limited to switching & routing video inputs and outputs. Can be used in conjunction
with basic IR remote which is included.
Both analog and digital audio only inputs. Audio only inputs can be routed according to zone output or embedded
onto HDMI content. Control of Audio routing can be achieved through the Netvio GO iOS, iPadOS and Android.
application or via the published API available online at www.netvio.co.uk
C
Used to send IR signals to a specific display area. Useful applications include sending IR signals from a 3rd party control
system to a display area. For this application it is important to use the provided 3.5mm to 3.5mm jack cable between
matrix and control system IR output ports. Netvio does not support the use of 3rd third party IR accessories.
D
Allows a single cable connection to send an IR signal to all displays simultaneously. For this application it is
important to use the provided 3.5mm to 3.5mm jack cable between matrix and control system IR output ports.
Netvio does not support the use of 3rd third party IR accessories.
EUsed to send IR signals received from the display location, then repeated to a media source via a supplied IR
emitter cable. Netvio does not support the use of 3rd third party IR accessories.
F
G
Point-to-point bi-directional communication from 3rd party control system to a single display location. Ensure TX to
RX & RX to TX wiring (including ground connections), Always use the provided green 3-pole connectors for matrix
side. At the display area, RS-232 connections are made available on all Netvio HDBaseT receivers.
H
Zone dedicated analog and digital outputs. S/PDIF supporting multi-channel. 3.5mm jack socket supporting L/R
stereo audio. Both outputs can operate simultaneously. Outputs can receive audio signals as a part of audio matrix
function and controlled through API or Netvio GO applications for iOS, iPadOS and Android.
IUSB charging function only. Provision for future product upgrade.
J
RJ-45 network connection for IP control. DHCP (auto assigned without DHCP). Required connection for use with
Netvio 360 configuration utility. RS-232 serial communication via 9W D connection. RS-232 interface cable
provided.
KGround screw for 3mm tag.
Universal mains power connection. IEC power cable provided.
Global IR Input Port
Audio Only Device Inputs
IR Input Ports
Global IR Input Port
IR Output Ports
Global IR Output Port
Direct Zone RS-232
Audio Outputs
USB Charging Ports
Communication Ports
Ground Connection
Power Connection
L
Rear Panel
Allows a single cable connection to send an IR signal to all media sources simultaneously. For this application it is
important to use the provided 3.5mm to 3.5mm jack cable between matrix and control system IR output ports.
Netvio does not support the use of 3rd third party IR accessories.
Drivers available at www.netvio.co.uk
8
Tabla de contenidos
Otros manuales de Conmutador de matriz de NETVIO
