NETGEAR WN203 Manual de usuario

)NSTALLATION'UIDE

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95135

version 1.0

English 1

Deutsch 7

Français 13

Русский 19

Contents

ProSAFE® Single Band 802.11n Wireless Access Point WN203

Installation Guide

Follow the instructions in this installation guide to set up your ProSAFE® Single

Band 802.11n Wireless Access Point WN203. For information about advanced

configuration options, see the reference manual.

Note: In this installation guide, the Wireless Access Point WN203 is referred to as

the access point.

Package Contents

Unpack the box and verify the contents:

•Wireless Access Point WN203

•Two external 2.4 GHz antennas

•Straight-through Category 5 Ethernet cable

•Power adapter and cord (12V, 1A)

•Stand

•Two wall mount screws and anchors

•Resource CD

•Installation guide

Set Up the Access Point

Setting up the access point consists of three short procedures:

•Attach the antennas and connect the access point to your computer.

•Configure the LAN and wireless access settings.

•Test wireless connectivity.

Estimated total time for these procedures: 15 minutes.

Tip: Before you mount the access point in a high location, first set up

and test the access point to verify wireless network connectivity.

English

ProSAFE® Single Band 802.11n Wireless Access Point WN203

English

Attach the Antennas and Connect the Access Point to

Your Computer

1. Attach the antennas to the SMA antenna connectors on the back panel.

2. Prepare a computer

with an Ethernet

adapter:

a. If this computer is

already part of your

network, record its

TCP/IP

configuration

settings.

b. Configure the

computer with a

static IP address of

192.168.0.210 and

a subnet mask of

255.255.255.0.

3. Insert an Ethernet

cable in the Ethernet

port of the computer

(point Ain the

illustration).

4. Securely insert the other end of the cable into the Ethernet LAN port on the

back panel of the access point (point Bin the illustration).

5. Connect the power adapter to the access point and plug the power adapter

into a power outlet.

6. Verify the following:

Power LED. The Power LED is green. If the Power LED is off, check

the connections, and check if the power outlet is controlled by a wall

switch that is turned off.

Test LED. The Test LED blinks amber at startup and turns off after

about one minute.

LAN LED. The LAN LED indicates LAN speeds: green for 1000 Mbps,

amber for 100 Mbps or 10 Mbps. If no link is detected, the LAN LED is off.

WLAN LED. The WLAN LED is blue, indicating that the wireless LAN

(WLAN) is ready.

LAN port

Console port

Power

connector

Antenna connector Antenna connector

English

Configure the LAN and Wireless Access Settings

1. On the computer that is connected to the access point, enter

http://192.168.0.100 in the address field of a browser.

A login window displays.

2. Enter admin for the user name and

password for the password, both in

lowercase letters.

The web management interface of

the access point displays. The menu

lets you navigate to the various

screens.

3. Select Configuration > System > Basic > General from the menu.

a. In the Access Point Name field, enter a unique name or leave the default

name.

b. From the Country/Region drop-down list, select the country where the

access point is installed.

c. Click Apply.

4. Select Configuration > IP > IP Settings from the menu.

By default, the access point has a static IP address of 192.168.0.100 with a

subnet mask of 255.255.255.0, and the DHCP client is disabled.

a. Configure the IP settings for your LAN.

b. Click Apply.

Tip: If you configure the access point as a DHCP client, reserve an

IP address on the DHCP server in your network by binding the

access point’s MAC address to the IP address that is issued

by the DHCP server. The next time that you log in to the

access point, you need to use the reserved IP address.

5. Select Configuration > Security > Profile Settings from the menu.

a. Configure one or more security profiles for your wireless network.

b. After configuring each security profile, click Apply.

6. Select Configuration > Wireless > Advanced > Wireless Settings.

a. Next to Antenna, select the External radio button to enable the external

antennas.

b. Click Apply.

English

Test Wireless Connectivity

Using a computer or another wireless device, verify that you can establish a

wireless connection to the access point. By default, the wireless radio of the

access point is on and the default wireless mode is ng (that is, 802.11ng).

Now that you have finished the setup, you are ready to deploy the access point in

your network. You can reconfigure the computer that you used to configure the

access point back to its original TCP/IP settings.

Deploy the Access Point

1. Disconnect the access point and position it where you plan to deploy it.

The best location is elevated such as wall or ceiling mounted, at the center of

your wireless coverage area, and within line of sight of all wireless devices.

2. Connect an Ethernet cable from the Ethernet LAN port on your access point

to a LAN port on your router, switch, or hub.

3. Connect the power adapter to the access point and plug the power adapter

into a power outlet.

The Power and LAN LEDs should light.

Tip: The access point supports Power over Ethernet (PoE). If you have

a switch that provides PoE, you do not need to use the power

adapter to power the access point. This can be especially

convenient when the access point is installed in a high location far

from a power outlet.

4. Using a computer or another wireless device, verify the following:

•You can establish a wireless connection to the access point.

•You can connect to the Internet through a browser.

•You can access files and printers on your network.

English

Troubleshooting Tips

This section provides some tips for correcting simple problems that you might

encounter. For more troubleshooting information, see the troubleshooting chapter

in the reference manual.

Problem Cause Possible Solution

No LEDs are lit

on the access

point.

The access point

has no power.

• Make sure that the power cord is connected to the

access point and plugged in to a working power

outlet or power strip.

• Make sure that you are using the correct

NETGEAR power adapter supplied with your

access point.

• If the access point is using PoE, make sure that

the PoE switch is providing power to the access

point.

The LAN LED

is off.

There is a

hardware

connection

problem.

• Make sure that the cable connectors are securely

plugged in to the access point and to the network

device (hub, [PoE] switch, or router).

• Make sure that the network device is turned on.

The WLAN

LED is off.

The wireless

connection does

not work.

• If the WLAN LED stays off, disconnect the power

adapter from its power source and then plug it in

again.

• Log in to the access point and verify that the radio

or radios are turned on.

• Contact NETGEAR if the WLAN LED remains off.

You cannot

configure the

access point

from a browser.

Multiple causes. • Make sure that the access point is correctly

installed, it is powered on, and the LAN

connections are good. Check that the LAN LED is

lit to verify that the Ethernet connection is good.

• Ensure that your computer is using an IP address

in the range of the access point. The access point

default IP address is 192.168.0.100, and the

default subnet mask is 255.255.255.0.

• Quit the browser, clear the cache, delete the

cookies, and launch the browser again.

English

Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product

and use it to register your product at https://my.netgear.com.

You must register your product before you can use NETGEAR telephone support.

NETGEAR recommends registering your product through the NETGEAR website.

For product updates and web support, visit http://support.netgear.com.

NETGEAR recommends that you use only the official NETGEAR support

resources.

You can get the user manual online at http://downloadcenter.netgear.com or

through a link in the product’s user interface.

For the current EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

You cannot

access the

Internet or the

LAN from a

wireless

device.

There is a

configuration

problem.

• You might not have restarted the wireless device

to let the TCP/IP changes take effect. Restart the

computer.

• Make sure that the SSID and wireless security

settings of the wireless device are the same as

those of the access point.

• The wireless device might not have the correct

TCP/IP settings to communicate with the network.

Restart the wireless device and check that TCP/IP

is set up correctly for that network. In Windows,

the usual setting for Network Properties is to

obtain an IP address automatically.

• The access point default values might not work

with your network. Check the access point default

configuration against the configuration of other

devices in your network.

For information about changing the default values

of the access point, see the reference manual.

Problem Cause Possible Solution

Installationsanleitung

Befolgen Sie zum Einrichten des ProSAFE® Single Band 802.11n Wireless Access

Points WN203 die Anweisungen in dieser Installationsanleitung. Nähere Informationen

zu erweiterten Konfigurationsoptionen finden Sie im Referenzhandbuch.

Hinweis: In dieser Installationsanleitung wird der Wireless Access Point WN203 als

„Access Point“ bezeichnet.

Lieferumfang

Folgendes muss im Karton enthalten sein:

•Wireless Access Point WN203

•Zwei externe 2,4-GHz-Antennen

•Durchgangs-Netzwerkkabel (Kategorie 5)

•Netzteil und -kabel (12 V/1 A)

•Fuß

•Zwei Dübel und Schrauben für die Wandmontage

•Ressourcen-CD

•Installationsanleitung

Einrichten des Access Points

Der Access Point lässt sich in drei kurzen Schritten einrichten:

•Bringen Sie die Antennen an, und schließen Sie den Access Point an den

Computer an.

•Konfigurieren Sie die Einstellungen des LAN- und WLAN-Zugriffs.

•Überprüfen Sie die drahtlose Verbindung.

Geschätzte Gesamtdauer: 15 Minuten.

Tipp: Bevor Sie den Access Point an einem erhöhten Standort aufstellen, sollten

Sie ihn einrichten und die Verbindung zum WLAN-Netzwerk prüfen.

Deutsch

ProSAFE® Single Band 802.11n Wireless Access Point WN203

Deutsch

Anbringen der Antennen und Anschließen des Access

Point an den Computer

1. Schließen Sie die Antennen an den SMA-Antennenstecker an der Rückseite des

Geräts an.

2. Bereiten Sie einen Computer mit einem Netzwerk-Adapter vor:

a. Wenn der Computer schon ins Netzwerk integriert ist, notieren Sie die TCP/IP-

Konfigurationseinstellungen.

b. Richten Sie den

Computer mit der

statischen IP-

Adresse

192.168.0.210 und

der Subnetzmaske

255.255.255.0 ein.

3. Stecken Sie ein

Netzwerkkabel in den

Netzwerkanschluss des

Computers (Schritt Ain

der Abbildung).

4. Stecken Sie das andere

Ende des Kabels in den

Netzwerk-LAN-Port an

der Rückseite des

Access Points (Schritt B

in der Abbildung).

5. Schließen Sie das

Netzteil an den Access

Point an, und stecken

Sie es in eine Steckdose.

6. Überprüfen Sie Folgendes:

Power-LED. Die Power-LED leuchtet grün.

Falls die Power-LED nicht leuchtet, überprüfen Sie die Anschlüsse und

außerdem die Stellung eines eventuell vorhandenen Steckdosenschalters.

Test-LED. Die Test-LED blinkt beim Start gelb und erlischt nach ca.

1 Minute.

LAN-LED. Die LAN-LED zeigt die LAN-Geschwindigkeit an: grün bei

1000 MBit/s, gelb bei 100 MBit/s oder 10 MBit/s. Wenn keine Verbindung

erkannt wird, leuchtet die LAN-LED nicht.

WLAN-LED. Die WLAN-LED leuchtet blau, was bedeutet, dass das

Wireless LAN (WLAN) bereit ist.

LAN-Port

Konsolen-Port

Netzanschluss

Antennenstecker Antennenstecker

Deutsch

Konfigurieren der Einstellungen des LAN- und WLAN-

Zugriffs

1. Geben Sie auf dem Computer, der mit dem Access Point verbunden ist,

http://192.168.0.100 in die Adresszeile eines Browsers ein.

Ein Anmeldefenster wird angezeigt.

2. Geben Sie als Benutzernamen admin

und als Passwort password ein. Beide

Wörter müssen klein geschrieben

werden.

Die Web-Management-

Benutzeroberfläche des Access Points

wird angezeigt. Über das Menü können

Sie zu den verschiedenen Bildschirmen navigieren.

3. Wählen Sie Configuration (Konfiguration) > System > Basic (Grundeinstellungen)

> General (Allgemein) aus dem Menü aus.

a. Geben Sie im Namensfeld Access Point einen eindeutigen Namen ein, oder

übernehmen Sie den Standardnamen.

b. Wählen Sie aus der Dropdown-Liste Country/Region (Land/Region) das

Land oder die Region aus, in dem/der der Access Point installiert ist.

c. Klicken Sie auf Apply (Übernehmen).

4. Wählen Sie Configuration (Konfiguration) > IP > IP Settings (IP-Einstellungen)

aus dem Menü aus.

Standardmäßig lautet die statische IP-Adresse des Access Points 192.168.0.100

und die Subnetzmaske 255.255.255.0, wobei der DHCP-Client deaktiviert ist.

a. Konfigurieren Sie die IP-Einstellungen für Ihr LAN.

b. Klicken Sie auf Apply (Übernehmen).

Tipp: Wenn Sie den Access Point als DHCP-Client konfigurieren,

reservieren Sie eine IP-Adresse auf dem DHCP-Server in Ihrem

Netzwerk, indem Sie die MAC-Adresse des Access Points an

die IP-Adresse binden, die vom DHCP-Server ausgegeben

wurde. Wenn Sie sich das nächste Mal am Access Point

anmelden, müssen Sie die reservierte IP-Adresse verwenden.

5. Wählen Sie Configuration (Konfiguration) > Security (Sicherheit) > Profile

Settings (Profileinstellungen) aus dem Menü aus.

a. Konfigurieren Sie ein oder mehrere Sicherheitsprofile für das WLAN-Netzwerk.

b. Klicken Sie nach der Konfiguration jedes Sicherheitsprofils auf Apply

(Übernehmen).

6. Wählen Sie Configuration (Konfiguration) > Wireless (WLAN) > Advanced

(Erweitert) > Wireless Settings (WLAN-Einstellungen).

a. Wählen Sie neben Antenna (Antenne) die Optionsschaltfläche External

(Extern) aus, um die externen Antennen zu aktivieren.

b. Klicken Sie auf Apply (Übernehmen).

Otros manuales para WN203

Tabla de contenidos

Idiomas:

Otros manuales de Punto de acceso inalámbrico de NETGEAR

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Manual de usuario

NETGEAR

NETGEAR WG602v4 - Wireless Access Point Manual

NETGEAR

NETGEAR WNAP210 Manual de usuario

NETGEAR

NETGEAR FWG114Pv2 - Wireless Firewall With USB Print... Manual de usuario

NETGEAR

NETGEAR SSL312 - ProSafe SSL VPN Concentrator 25 Manual de usuario

NETGEAR

NETGEAR WG302v1 - ProSafe 802.11g Wireless Access... Guía rápida

NETGEAR

NETGEAR WAX220 Manual de usuario

NETGEAR

NETGEAR WN370 Manual de usuario

NETGEAR

NETGEAR WG302v2 - ProSafe 802.11g Wireless Access... Instrucciones de instalación

NETGEAR

NETGEAR WG302v2 - ProSafe 802.11g Wireless Access... Instrucciones de funcionamiento

NETGEAR

NETGEAR WN604 - Wireless-N 150 Access Point Manual de usuario

NETGEAR

NETGEAR WNTR2001 Manual de usuario

NETGEAR

NETGEAR WNHDE111 Manual de usuario

NETGEAR

NETGEAR WNHDE111 Manual de usuario

NETGEAR

NETGEAR WAC124 Manual de usuario

NETGEAR

NETGEAR WAX630 Manual de usuario

NETGEAR

NETGEAR WG302v1 - ProSafe 802.11g Wireless Access... Instrucciones de instalación

NETGEAR

NETGEAR WE102 - Wireless Access Point Manual de usuario

NETGEAR

NETGEAR WAX204 Manual de usuario

NETGEAR

NETGEAR ME103 - 802.11b ProSafe Wireless Access... Manual de usuario

NETGEAR

NETGEAR WN804 Manual de usuario

NETGEAR

NETGEAR ProSafe WG102-500 Manual de usuario

NETGEAR

NETGEAR WAC124-100NAS Manual de usuario

NETGEAR

NETGEAR ProSafe Premium WNDAP660 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario