NETGEAR ProSafe FS752TP Manual

350 East Plumeria Drive

San Jose, CA 95134

USA

May 2011

202-10813-01

v1.0

FS752TP Smart Switch

Hardware Installation Guide

FS752TP Smart Switch

No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated

into any language in any form or by any means without the written permission of NETGEAR, Inc.

Technical Support

Thank you for choosing NETGEAR. To register your product, get the latest product updates, get support online, or

for more information about the topics covered in this manual, visit the Support website at

http://support.netgear.com .

Phone (US & Canada only): 1-888-NETGEAR

Phone (Other Countries): Check the list of phone numbers at

http://support.netgear.com/app/answers/detail/a_id/984

Trademarks

NETGEAR, the NETGEAR logo, ReadyNAS, ProSafe, ProSecure, Smart Wizard, Auto Uplink, X-RAID2, and

NeoTV are trademarks or registered trademarks of NETGEAR, Inc. Microsoft, Windows, Windows NT, and Vista

are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or

trademarks of their respective holders.

Statement of Conditions

To improve internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes

to the products described in this document without notice. NETGEAR does not assume any liability that may occur

due to the use, or application of, the product(s) or circuit layout(s) described herein.

Revision History

Publication Part Number Version Publish Date Comments

202-10813-01 v1.0 May 2011 First publication

Contents

Chapter 1 Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Chapter 2 Physical Description

FS752TP Front-Panel and Back-Panel Configuration . . . . . . . . . . . . . . . .10

LED Designations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

System LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Port LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Device Hardware Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

RJ-45 Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

SFP Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Reset Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Factory Defaults Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Chapter 3 Applications

Desktop Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 4 Installation

Step 1: Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Rackmount Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Step 2: Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Installing the Switch on a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . .21

Installing the Switch in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Step 3: Checking the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Step 4: Connecting Devices to the Switch . . . . . . . . . . . . . . . . . . . . . . . . .23

Step 5: Installing an SFP Transceiver Module . . . . . . . . . . . . . . . . . . . . . .24

Step 6: Applying AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Step 7: Managing the Switch using a Web Browser or the PC Utility. . . . .26

Appendix A Troubleshooting

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Additional Troubleshooting Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . .29

Network Adapter Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Switch Integrity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Auto-Negotiation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

FS752TP Smart Switch

Appendix B Technical Specifications

Appendix C Notification of Compliance

Index

1. Introduction

Congratulations on the purchase of your NETGEAR®ProSafeTM FS752TP Smart Switch!

Your FS752TP switch is a state-of-the-art, high-performance, IEEE-compliant network

solution designed for users who require a large number of ports and want the power of

Gigabit connectivity to eliminate bottlenecks, boost performance, and increase productivity.

There are 48 twisted-paired ports with four gigabit ports (two are combo ports with SFP GBIC

slots) on the front panel of the switch. To simplify installation, the switch is shipped ready for

use out of the box.

The FS752TP Smart Switch Hardware Installation Guide describes how to install and power

on the FS752TP. The information in this manual is intended for readers with intermediate

computer and Internet skills.

This chapter serves as an introduction to the FS752TP and provides the following

information:

• Overview

• Features

• Package Contents

Introduction

FS752TP Smart Switch

Overview

The NETGEAR FS752TP Smart Switch has:

• 48 Fast Ethernet RJ45 PoE ports with auto sensing, supporting 10/100M speed. Ports 1-4

provide maximum power of 30W and ports 5-48 provide maximum power of 15.4W. The

total PoE power budge is 384W.

• 2 Gigabit combo ports with auto sensing, supporting 10/100/1000M speed on RJ45 and

100/1000M on SFP.

• 2 10/100/1000M Gigabit Uplink Ports

Available memory types of the switch are the following:

• 16 bit 64 MB DDR SDRAM memory

• 16 MB Serial flash for Application Code and OS

The switch can store up to two images in FLASH. It can be configured to boot with the image

of the user’s choice.

Using these Gigabit slots, you can create high-speed connections to a server or network

backbone. For example, you can:

• Connect switches to each other with high-speed links

• Link to high-speed servers

• Provide 10/100/1000M copper and 1000M fiber connectivity

The NETGEAR FS752TP Smart Switch also provides the benefit of administrative

management with a complete package of features for the observation, configuration, and

control of the network. With a Web-based Graphical User Interface (GUI), the switch’s many

capabilities can be viewed and used in a simple and intuitive manner. The switch’s

management features include configuration for port and switch information, VLAN for traffic

control, port trunking for increased bandwidth, and Class of Service (CoS) for traffic

prioritization. These features provide better understanding and control of the network. Initial

discovery of the switch on the network requires the Smart Control Center program, a utility

that runs on a PC.

The NETGEAR FS752TP Smart Switch is a standard 1U chassis high/17” rack mounted in a

wiring closet or equipment room. It is IEEE-compliant and offers low latency for high-speed

networking. All ports can automatically negotiate to the highest speed. This capability makes

the switch ideal for environments that have a mix of Ethernet, Fast Ethernet, or Gigabit

Ethernet devices. In addition, all RJ-45 ports operate in half-duplex or full-duplex mode. The

maximum segment length is 328 feet (100 meters) over Category 5 Unshielded Twisted-Pair

(UTP) cable.

Introduction

FS752TP Smart Switch

Features

The following list identifies the key features supported by the FS752TP:

• The 10/100/1000 Base-T ports are auto-sensing using RJ-45 UTP connectors.

• Auto MDI/MDI-X sensing and auto-negotiation is supported on all ports.

• Full-duplex flow control.

• Half-duplex back pressure control.

• Head-of-line blocking prevention .

• MAC aging.

• Static MAC addresses entry and dynamic MAC addresses learning.

• VLANs

• IEEE 802.1Q up to 128 VLAN entries.

• Protected ports functionality which is similar to Port based VLANs.

• 802.3ad Link Aggregation.

• Setting LAGs manually or dynamically using LACP.

• Auto-Voice VLAN.

• Port mirroring (many to one), including the ability to Mirror RX, TX, or both.

• CoS and QoS.

• Broadcast, Multicast, and Unknown Unicast storm protection by specifying the threshold

as a percentage of port-speed.

• Spanning Tree (IEEE 802.1d).

• IEEE 802.1s MSTP and IEEE 802.1w, Rapid Reconfiguration Spanning Tree.

• L4 QoS ACL.

• Policy-based DiffServ.

• NETGEAR Green product series power-saving features:

• Per port automatic power down when the port link is down.

Introduction

FS752TP Smart Switch

Package Contents

Figure 1 shows the package contents of the FS752TP Smart Switch.

Ports 1-48, Link/Act Mode — Green=Link at 100M, Yellow=Link at 10M Blink=ACT

Ports 49-52 Link/Act Mode —Green=1G, Yellow=10/100M Blink=ACT

Power

Reset

Select

Fan

PoE Max

LED Mode

Yellow=PoE

Green=Link/ACT

Factory

Defaults

12345678910 11 13 15 17 19 21

12 2214 16 18 20 23 25 27 29 31 33

24 3426 28 30 32 35 37 39 41 43 45 47

36 38 40 42 44 46 48 52

FS752TP

50F 50T

49F 49T

Combo Ports

Figure 1. Package Contents

Verify that the package contains the following:

• FS752TP Smart Switch

• Rubber footpads for tabletop installation

• Rackmounting kits

• Power cord

• Installation guide

• Smart Switch Resource CD with NETGEAR Smart Control Center and User’s Manual

If any item is missing or damaged, contact the place of purchase immediately.

2. Physical Description

This chapter describes the FS752TP Smart Switch hardware features. Topics include:

• FS752TP Front-Panel and Back-Panel Configuration

• LED Designations

• Device Hardware Interfaces

Physical Description

FS752TP Smart Switch

FS752TP Front-Panel and Back-Panel Configuration

The FS752TP has:

• 48 10/100 Mbps copper ports

• Ports 49, 50 with RJ45 connectors that support 10/100/1000 Mbps

• Ports 51 and 52 with RJ45 connectors that support 10/100/1000 Mbps only

• Two SFP ports (Combo ports). The SFP combo ports are shared with copper ports 49 and

50. If the SFP combo ports are in use, copper ports 49 and 50 are inactive.

Each port is capable of sensing the line speed and negotiating the duplex mode with the link

partner automatically.

Figure 2 illustrates the front panel of the NETGEAR FS752TP.

Power/Status LED

Reset Button

Factory Defaults

Button 10/100 Mbps copper ports

Combo Ports

Figure 2. Front Panel

The front panel contains the following:

• 48 RJ-45 connectors for 10/100 Mbps autosensing Fast Ethernet switching ports

• Two SFP combo Gigabit Ethernet switching ports

• Two dedicated 1000 Mbps Gigabit Ethernet switching ports

• Reset button to restart the device

• Recessed Factory Defaults button to restore the device back to the factory defaults

• Link, Speed, and Activity LEDs for each port

• Power and Status LED

• Fan

• PoE Max LED which is activated when less than 7W of the available PoE power remain

unused.

• LED Mode

Figure 3 illustrates the NETGEAR FS752TP back panel.

Otros manuales para ProSafe FS752TP

Tabla de contenidos

Otros manuales de Cambiar de NETGEAR

NETGEAR

NETGEAR GSM7248R - ProSafe Switch Manual del propietario

NETGEAR

NETGEAR GSM7312 - ProSafe Layer 3 Managed Gigabit... Manual de usuario

NETGEAR

NETGEAR GS324P Manual de usuario

NETGEAR

NETGEAR FSM7326P - ProSafe Managed Switch Manual

NETGEAR

NETGEAR GSM7224v2 - Layer 2 Managed Gigabit Switch Manual

NETGEAR

NETGEAR M4250 Series Manual de usuario

NETGEAR

NETGEAR FS728TP - ProSafe 24 Port 10/100 Smart... Manual de instrucciones

NETGEAR

NETGEAR ProSafe GSM7228PS Manual de usuario

NETGEAR

NETGEAR ProSafe GS105 Manual de usuario

NETGEAR

NETGEAR GS305EP Manual de usuario

NETGEAR

NETGEAR GS105A Manual de usuario

NETGEAR

NETGEAR ProSAFE M7100-24X Manual de usuario

NETGEAR

NETGEAR GSM7312NA Manual de usuario

NETGEAR

NETGEAR GS408EPP Manual de usuario

NETGEAR

NETGEAR FS105 Manual de usuario

NETGEAR

NETGEAR ProSAFE JGS524Ev2 Manual de usuario

NETGEAR

NETGEAR ProSAFE GS105Ev2 Manual de usuario

NETGEAR

NETGEAR Universal Pro XS508M Manual de usuario

NETGEAR

NETGEAR GS728TPv2 Manual de usuario

NETGEAR

NETGEAR ProSafe GS108P Manual de usuario

NETGEAR

NETGEAR GS716T - ProSafe Switch Manual de usuario

NETGEAR

NETGEAR FS108 - ProSafe 10/100 Desktop Switch Manual de usuario

NETGEAR

NETGEAR GS418TPP Manual de usuario

NETGEAR

NETGEAR ProSafe JGSM7224 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario