NETGEAR MS510TXM Manual

Hardware Installation Guide

8-Port Multi-Gigabit/10G Ethernet

(Ultra60 PoE++) Smart Managed Pro Switch

with 2 SFP+ Ports

Models

MS510TXM

MS510TXUP

NETGEAR, Inc.

350 E. Plumeria DriveJanuary 2021

San Jose, CA 95134, USA202-12153-01

Support and Community

Visit netgear.com/support to get your questions answered and access the latest

downloads.

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Regulatory and Legal

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français

canadien à https://www.netgear.com/support/download/.

(If this product is sold in Canada, you can access this document in Canadian French at

https://www.netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

For NETGEAR’s Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR’s Terms and Conditions at

https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the

device to your place of purchase within your return period.

Do not use this device outdoors. The PoE source is intended for intra building connection

only.

Trademarks

Any non-NETGEAR trademarks are used for reference purposes only.

Revision History

CommentsPublish DatePublication Part

Number

First publication.January 2021202-12153-01

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

Contents

Chapter 1 Introduction

Overview................................................................................................6

Features.................................................................................................6

Safety instructions and warnings........................................................8

Chapter 2 Hardware Overview

Hardware overview of model MS510TXM......................................12

Front panel model MS510TXM....................................................12

LEDs model MS510TXM...............................................................13

Back panel model MS510TXM.....................................................13

Hardware overview of model MS510TXUP.....................................14

Front panel model MS510TXUP..................................................14

LEDs model MS510TXUP..............................................................15

Back panel model MS510TXUP...................................................16

Switch hardware interfaces...............................................................17

RJ-45 ports for 100/1000M and 2.5G/5G/10G BASE-T Ethernet

connectivity.....................................................................................17

Transceiver modules and cables for SFP+ fiber ports..............18

Multi-function Reset button..........................................................18

PoE port capacities and budget for model MS510TXUP..........19

Chapter 3 Applications

Multispeed PoE++ and PoE+ access points and cameras............22

Multispeed backbone switching.......................................................23

10G network storage and redundancy............................................24

Chapter 4 Installation

Step 1: Prepare the site......................................................................26

Step 2: Protect against electrostatic discharge..............................26

Step 3: Unpack the switch.................................................................27

Step 4: Install the switch....................................................................28

Install the switch in a rack..............................................................28

Install the switch on a flat surface.................................................29

Optional Step 5: Install an SFP transceiver module or cable........29

Step 6: Connect devices to the switch.............................................30

Step 7: Check the installation...........................................................31

Step 8: Apply power and check the LEDs.......................................31

Step 9: Manage the switch................................................................32

Chapter 5 Troubleshooting

Troubleshooting chart.......................................................................36

PoE troubleshooting suggestions....................................................37

Additional troubleshooting suggestions.........................................38

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

Introduction

This hardware installation guide complements the installation guide that came with your

switch and applies to the following NETGEAR switch models:

•MS510TXM: 8-Port Multi-Gigabit/10G Ethernet Smart Managed Pro Switch with 2

SFP+ Ports

•MS510TXUP: 8-Port Multi-Gigabit/10G Ethernet Ultra60 PoE++ Smart Managed

Pro Switch with 2 SFP+ Ports

The switch provides eight Gigabit Ethernet multispeed copper ports and two dedicated

SFP+ fiber uplink ports that support 1G and 10G. Four of the multispeed copper ports

support 100M, 1G, and 2.5G and each of the other four multispeed copper ports

supports 100M, 1G, 2.5G, 5G, and 10G.

Model MS510TXUP can provide Ultra60 PoE++ (802.3bt) on its eight multispeed copper

ports so that you can let the switch deliver power to PoE++ devices such as WiFi 6 access

points, security cameras, PoE speakers, and LED lighting. Model MS510TXUP can supply

up to 60W PoE++ to each copper port, with a maximum PoE power budget of 295W

across all active PoE++ ports.

This chapter serves as an introduction to the switch and includes the following sections:

• Overview

• Features

• Safety instructions and warnings

Note: For more information about the topics that are covered in this manual, visit the

support website at netgear.com/support.

Note: For technical specifications, see the data sheet at

netgear.com/business/products/switches/smart. For switch documentation, including

the installation guide and user manual, visit netgear.com/support/download.

Overview

The switch provides eight Gigabit Ethernet multispeed copper ports and two dedicated

SFP+ fiber uplink ports that support 10G and 1G. Four of the multispeed copper ports

support both 1G and 2.5G and each of the other four multispeed copper ports supports

1G, 2.5G, 5G, and 10G. All copper ports use RJ-45 connectors.

The SFP+ ports require standard small form-factor pluggable (SFP) gigabit interface

converters (GBICs, also referred to as a transceiver modules), which are sold separately

from the switch. The switch integrates 140 Gbps line-rate, full-duplex, nonblocking

switch fabric.

The PoE model supports Ultra60 PoE++ (802.3bt) on all copper ports (that is, up to 60W

PoE++ to each port) with a maximum PoE power budget of 295W across all active PoE++

ports.

Note: For information about application examples, see Applications on page 21.

You can install the switch freestanding or rack mounted in a wiring closet or equipment

room. The switch is IEEE compliant and offers low latency. All ports can automatically

negotiate to the highest speed, which makes the switch very suitable for a mixed

environment with multispeed Gigabit Ethernet, Gigabit Ethernet, and Fast Ethernet.

For speeds of 10 Gbps, use Category 6 (Cat 6) cables terminated with RJ-45 connectors;

for speeds from 5 Gbps to 10 Gbps, use Cat 5e cables terminated with RJ-45 connectors;

and for speeds from 10 Mbps to 5 Gbps, including 2.5 Gbps, use Cat 5e or higher-rated

Ethernet cables terminated with RJ-45 connectors.

Features

The switch supports the following key hardware features:

•Four multispeed Ethernet ports (5–8), each of which supports 10G, 5G, 2.5G, 1G,

and 100M.

•Four multispeed Ethernet ports (1–4), each of which supports 2.5G, 1G, and 100M.

•Two dedicated SFP+ fiber uplink ports (9F and 10F), each of which is capable of 10G

and 1G.

•PoE support for model MS510TXUP:

- Eight Ultra60 PoE++ (802.3bt) ports

-Total PoE power budget of 295W for the switch

Hardware Installation Guide6Introduction

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

•MAC table size of 32K.

•Two fans for model MS510TXM and three fans for model MS510TXUP with

variable-speeds that can lower the noise level during low temperatures.

•Acoustic noise at 25°C is equal to or less than 25 dBA for model MS510TXM and 33

dBA for model MS510TXUP.

•140 Gbps line-rate, full-duplex, nonblocking switch fabric.

•Includes 19-inch rack-mount kit for rack installation.

•Full compatibility with IEEE standards:

- IEEE 802.3 Ethernet

- IEEE 802.3u 100BASE-T

- IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX

- IEEE 802.3bz NBASE-T and MGBASE-T

- IEEE 802.3an (10GBASE-T)

-IEEE 802.3ae 10-Gigabit Ethernet over fiber (10GBASE-SR, 10GBASE-LR)

- IEEE 802.3ab 1000BASE-T

- IEEE 802.3i 10BASE-T

- IEEE 802.1Q VLAN tagging

-IEEE 802.3x Full-duplex flow control

- IEEE 802.3ad Link aggregation (LAG with LACP)

- IEEE 802.1ab LLDP

-IEEE 802.1p Class of Service (QoS)

- IEEE 802.1D Spanning Tree Protocol (STP)

- IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)

- IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)

- IEEE 802.1x RADIUS network access control

-IEEE 802.3az Energy Efficient Ethernet (EEE)

-IEEE 802.1af (PoE, model MS510TXUP)

- IEEE 802.1at (PoE+, model MS510TXUP)

- IEEE 802.1bt (PoE++, model MS510TXUP)

•AutoSensing and autonegotiating capabilities for all ports.

•Auto Uplink™ technology is supported on all ports.

Hardware Installation Guide7Introduction

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

•Automatic address learning function to build the packet-forwarding information

table. The table contains up to 32K Media Access Control (MAC) addresses.

•Store-and-forward transmission to remove bad packets from the network.

•Active flow control to minimize packet loss and frame drops.

•Half-duplex backpressure control.

•Per-port status LEDs and system status LEDs.

•NETGEAR green power-saving features:

-Energy efficiency mode that fully conforms to the IEEE802.3az standard

- Per-port automatic change to a lower power mode when the port link is down

Safety instructions and warnings

Use the following safety guidelines to ensure your own personal safety and to help

protect your system from potential damage.

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions:

•This product is designed for indoor use only in a temperature-controlled and

humidity-controlled environment. Note the following:

-For more information about the environment in which this product must operate,

see the environmental specifications in the appendix or the data sheet.

-If you want to connect the product to a device located outdoors, the outdoor

device must be properly grounded and surge protected, and you must install an

Ethernet surge protector inline between the indoor product and the outdoor

device. Failure to do so can damage the product.

-Before connecting the product to outdoor cables or devices, see

https://kb.netgear.com/000057103 for additional safety and warranty information.

Failure to follow these guidelines can result in damage to your NETGEAR product,

which might not be covered by NETGEAR’s warranty, to the extent permissible by

applicable law.

•Observe and follow service markings:

- Do not service any product except as explained in your product documentation.

Some devices should never be opened.

-If applicable to your product, opening or removing covers that are marked with

the triangular symbol with a lightning bolt can expose you to electrical shock.

Hardware Installation Guide8Introduction

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

We recommend that only a trained technician services components inside these

compartments.

•If any of the following conditions occur, unplug the product from the power outlet,

and then replace the part or contact your trained service provider:

- Depending on your product, the power adapter, power adapter cable, power

cable, extension cable, or plug is damaged.

-An object fell into the product.

- The product was exposed to water.

- The product was dropped or damaged.

-The product does not operate correctly when you follow the operating

instructions.

•Keep the product away from radiators and heat sources. Also, do not block cooling

vents.

•Do not spill food or liquids on your product components, and never operate the

product in a wet environment. If the product gets wet, see the appropriate section

in your troubleshooting guide, or contact your trained service provider.

•Do not push any objects into the openings of your product. Doing so can cause fire

or electric shock by shorting out interior components.

•Use the product only with approved equipment.

•If applicable to your product, allow the product to cool before removing covers or

touching internal components.

•Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required,

consult your service provider or local power company.

•To avoid damaging your system, if your product uses a power supply with a voltage

selector, be sure that the selector is set to match the power at your location:

-115V, 60 Hz in most of North and South America and some Far Eastern countries

such as South Korea and Taiwan

- 100V, 50 Hz in eastern Japan and 100V, 60 Hz in western Japan

-230V, 50 Hz in most of Europe, the Middle East, and the Far East

•Be sure that attached devices are electrically rated to operate with the power available

in your location.

•Depending on your product, use only a supplied power adapter or approved power

cable:

Hardware Installation Guide9Introduction

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

If your product uses a power adapter:

-If you were not provided with a power adapter, contact your local NETGEAR

reseller.

-The power adapter must be rated for the product and for the voltage and current

marked on the product electrical ratings label.

If your product uses a power cable:

-If you were not provided with a power cable for your system or for any

AC-powered option intended for your system, purchase a power cable approved

for your country.

-The power cable must be rated for the product and for the voltage and current

marked on the product electrical ratings label. The voltage and current rating of

the cable must be greater than the ratings marked on the product.

•To help prevent electric shock, plug the system and peripheral power cables into

properly grounded power outlets.

•If applicable to your product, the peripheral power cables are equipped with

three-prong plugs to help ensure proper grounding. Do not use adapter plugs or

remove the grounding prong from a cable. If you must use an extension cable, use

a three-wire cable with properly grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total ampere

rating of all products plugged into the extension cable or power strip does not

exceed 80 percent of the ampere ratings limit for the extension cable or power strip.

•To help protect your system from sudden, transient increases and decreases in

electrical power, use a surge suppressor, line conditioner, or uninterruptible power

supply (UPS).

•Position system cables, power adapter cables, or power cables carefully. Route

cables so that they cannot be stepped on or tripped over. Be sure that nothing rests

on any cables.

•Do not modify power adapters, power adapter cables, power cables or plugs. Consult

a licensed electrician or your power company for site modifications.

•Always follow your local and national wiring rules.

Hardware Installation Guide10Introduction

8-Port Multi-Gigabit/10G Ethernet (Ultra60 PoE++) Smart Managed Pro Switch with 2 SFP+ Ports

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de NETGEAR

NETGEAR

NETGEAR GS105E Manual de usuario

NETGEAR

NETGEAR M4100 Series ProSAFE Guía del usuario

NETGEAR

NETGEAR 10/100/1000 Manual de usuario

NETGEAR

NETGEAR SB104 Network Starter Kit SB104 SB104 Manual de usuario

NETGEAR

NETGEAR GSM7224 - Switch Manual

NETGEAR

NETGEAR ProSafe GS116 Manual de usuario

NETGEAR

NETGEAR FS208 Manual de usuario

NETGEAR

NETGEAR GS108Tv3 Manual de usuario

NETGEAR

NETGEAR GS108T - ProSafe - Gigabit Smart Switch Manual de usuario

NETGEAR

NETGEAR GSM7248R - ProSafe Switch Manual del propietario

NETGEAR

NETGEAR ProSafe GSM5212P Manual de usuario

NETGEAR

NETGEAR GS724TS - ProSafe 24 Port Gigabit Stackable Smart... Manual de usuario

NETGEAR

NETGEAR ProSafe XS712T Manual

NETGEAR

NETGEAR GC110 Manual

NETGEAR

NETGEAR FS726T - ProSafe Smart Switch Manual de usuario

NETGEAR

NETGEAR WFS709TP - ProSafe Smart Wireless Controller Manual

NETGEAR

NETGEAR ProSafe GS108 Manual de usuario

NETGEAR

NETGEAR FS 750 Manual de usuario

NETGEAR

NETGEAR FSM726 - ProSafe Managed Switch Manual de usuario

NETGEAR

NETGEAR ProSafe FS750T Manual de usuario

NETGEAR

NETGEAR 7300 Series Manual de usuario

NETGEAR

NETGEAR M6100 Series Manual

NETGEAR

NETGEAR ProSAFE M7100-24X Manual de usuario

NETGEAR

NETGEAR FSM726v3 - ProSafe Fast Ethernet L2 Managed... Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario