NETGEAR GS408EPP Manual

Hardware Installation Guide

8-Port Easy Mount Gigabit Ethernet PoE+

Smart Managed Plus Switch

Model GS408EPP

NETGEAR, Inc.

350 E. Plumeria DriveJanuary 2019 San Jose, CA 95134, USA202-11694-03

Support

Thank you for purchasing this NETGEAR product. You can visit

https://www.netgear.com/support/ to register your product, get help, access the latest

downloads and user manuals, and join our community. We recommend that you use

only official NETGEAR support resources.

Compliance and Conformity

For regulatory compliance information including the EU Declaration of Conformity, visit

https://www.netgear.com/about/regulatory/.

See the regulatory compliance document before connecting the power supply.

Do not use this device outdoors. If you connect cables or devices that are outdoors to

this device, see http://kb.netgear.com/000057103 for safety and warranty information.

Trademarks

Any non-NETGEAR trademarks are used for reference purposes only.

Revision History

CommentsPublish DatePublication Part

Number

•Updated the product name and published the manual in a new format.

•Removed information about the resource CD.

•Added Overview on page 5.

•Changed Safety instructions and warnings on page 7.

•Changed Status LEDs on page 12.

•Changed Step 1: Prepare the site on page 19.

•Changed Step 3: Unpack the switch on page 20.

•Added Step 5: Connect devices to the switch on page 24.

•Added Step 8: Manage the switch on page 25.

•Added PoE troubleshooting suggestions on page 29.

•Made multiple other minor changes.

January 2019202-11694-03

Updated the table in Step 1: Prepare the site on page 19.December 2016202-11694-02

First publication.October 2016202-11694-01

8-Port Easy Mount Gigabit Ethernet PoE+

Contents

Chapter 1 Introduction

Overview................................................................................................5

Features.................................................................................................6

Safety instructions and warnings........................................................7

Chapter 2 Hardware Overview

Front panel..........................................................................................11

Back panel and bottom panel...........................................................11

Status LEDs..........................................................................................12

Switch hardware interfaces...............................................................13

RJ-45 ports for 10/100/1000M BASE-T Ethernet connectivity..13

Factory Defaults button.................................................................13

Chapter 3 PoE Applications

PoE overview.......................................................................................15

Connect PoE equipment for surveillance and security..................16

Connect PoE equipment in a business environment.....................17

Chapter 4 Installation

Step 1: Prepare the site......................................................................19

Step 2: Protect against electrostatic discharge..............................20

Step 3: Unpack the switch.................................................................20

Step 4: Install the switch....................................................................21

Mount the switch to a wall............................................................21

Attach the switch to a pole or table leg......................................22

Install the switch in a rack..............................................................23

Step 5: Connect devices to the switch.............................................24

Step 6: Check the installation...........................................................25

Step 7: Apply power and check the LEDs.......................................25

Step 8: Manage the switch................................................................25

Chapter 5 Troubleshooting

Troubleshooting chart.......................................................................28

PoE troubleshooting suggestions....................................................29

Additional troubleshooting suggestions.........................................29

Introduction

The NETGEAR 8-Port Easy Mount Gigabit Ethernet PoE+ Smart Managed Plus Switch

Model GS408EPP is specifically designed to “put your ports where you want them” to

power your IP security cameras, WiFi access points, or VoIP phones with PoE+ (802.3at)

up to 30W per port.

This switch provides eight Gigabit ports in a unique form factor that can be wall mounted,

pole mounted, under table, ceiling air-duct, desktop, or 1U rack mounted with two units

per 1U slot with one facing forward and one facing the rear (all connections are on the

front of the switch).

This hardware installation guide complements the installation guide that came with your

switch.

This chapter serves as an introduction to the switch and includes the following sections:

• Overview

• Features

• Safety instructions and warnings

Note: For more information about the topics that are covered in this manual, visit the

support website at netgear.com/support/.

Note: For technical specifications, see the data sheet at

netgear.com/business/products/switches/web-managed/. For switch documentation,

visit netgear.com/support/download/.

Overview

The switch provides eight 10/100/1000BASE-T RJ-45 copper ports that support nonstop

10/100/1000M Layer 2 networks. All RJ-45 ports support PoE+ with a total PoE power

budget of 124W for the switch.

For information about PoE application samples, see PoE Applications on page 14.

The switch provides administrative management options that let you configure, monitor,

and control the network. Using the local browser–based management interface, in this

guide referred to as the local browser interface, you can configure the switch and the

network, including the ports, the management VLAN, VLANs for traffic control, link

aggregation for increased bandwidth, Quality of Service (QoS) for prioritizing traffic,

and network security.

For initial discovery of the switch on the network, use one of the following methods, all

of which are described in detail in the user manual:

•NETGEAR Insight mobile app

•NETGEAR Switch Discovery Tool

•NETGEAR ProSAFE Plus Utility

You can also get the IP address of the switch from the DHCP server in the network or

use an IP scanner utility.

After discovery, you can configure the switch using the local browser interface for

advanced setup and configuration of features, or the NETGEAR ProSAFE Plus Utility for

very basic setup. For more information, see the user manual, which you can download

from netgear.com/support/download/.

The switch is IEEE compliant and offers low latency. All ports can automatically negotiate

to the highest speed, which makes the switch very suitable for a mixed environment

with Fast Ethernet and Gigabit Ethernet.

Use Category 5e (Cat 5e) or higher-rated Ethernet cables terminated with RJ-45

connectors to make Gigabit connections.

Hardware Installation Guide5Introduction

8-Port Easy Mount Gigabit Ethernet PoE+ Smart Managed Plus Switch GS408EPP

Features

The switch supports the following key hardware features:

•8 Gigabit Ethernet ports that support PoE+ (802.3at).

•Total PoE power budget of 124W for the switch.

•16 Gbps switching fabric (duplex mode, all ports line-rate).

•Industry-unique chassis for desktop operation, wall operation, rack-mounting in a

wiring closet or equipment room, or attachable almost anywhere using the

Easy-Mount system.

•Full compatibility with IEEE standards:

- IEEE 802.3 Ethernet

- IEEE 802.3u 100BASE-T

- IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX

- IEEE 802.3ab 1000BASE-T

- IEEE 802.3i 10BASE-T

- IEEE 802.1Q VLAN tagging

-IEEE 802.3x Full-duplex flow control

-IEEE 802.1p Class of Service (QoS)

-IEEE 802.3az Energy Efficient Ethernet (EEE)

-IEEE 802.1af (PoE)

- IEEE 802.1at (PoE+)

•AutoSensing and autonegotiating capabilities for all ports.

•Auto Uplink technology is supported on all ports.

•Automatic address learning function to build the packet-forwarding information

table. The table contains up to 8K Media Access Control (MAC) addresses.

•Store-and-forward transmission to remove bad packets from the network.

•Active flow control to minimize packet loss and frame drops.

•Half-duplex backpressure control.

•Per-port status LEDs and system status LEDs.

•Per-port PoE status LEDs and system PoE Max LED.

Hardware Installation Guide6Introduction

8-Port Easy Mount Gigabit Ethernet PoE+ Smart Managed Plus Switch GS408EPP

•NETGEAR green power-saving features:

-Energy efficiency mode that fully conforms to the IEEE802.3az standard.

- Per-port automatic change to a lower power mode when the port link is down.

Safety instructions and warnings

Use the following safety guidelines to ensure your own personal safety and to help

protect your system from potential damage.

To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment,

observe the following precautions:

•This product is designed for indoor use only in a temperature-controlled and

humidity-controlled environment. For more information, see the environmental

specifications in the appendix or the data sheet.

Any device that is located outdoors and connected to this product must be properly

grounded and surge protected.

Failure to follow these guidelines can result in damage to your NETGEAR product,

which might not be covered by NETGEAR’s warranty, to the extent permissible by

applicable law.

•Observe and follow service markings:

- Do not service any product except as explained in your system documentation.

Some devices should never be opened.

-If applicable to your device, opening or removing covers that are marked with

the triangular symbol with a lightning bolt can expose you to electrical shock.

We recommend that only a trained technician services components inside these

compartments.

•If any of the following conditions occur, unplug the product from the electrical outlet

and replace the part or contact your trained service provider:

- Depending on your device, the power adapter, power adapter cable, power

cable, extension cable, or plug is damaged.

-An object fell into the product.

- The product was exposed to water.

- The product was dropped or damaged.

-The product does not operate correctly when you follow the operating

instructions.

Hardware Installation Guide7Introduction

8-Port Easy Mount Gigabit Ethernet PoE+ Smart Managed Plus Switch GS408EPP

•Keep your system away from radiators and heat sources. Also, do not block cooling

vents.

•Do not spill food or liquids on your system components, and never operate the

product in a wet environment. If the system gets wet, see the appropriate section in

your troubleshooting guide, or contact your trained service provider.

•Do not push any objects into the openings of your system. Doing so can cause fire

or electric shock by shorting out interior components.

•Use the product only with approved equipment.

•If applicable to your device, allow the product to cool before removing covers or

touching internal components.

•Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required,

consult your service provider or local power company.

•To avoid damaging your system, if your device uses a power supply with a voltage

selector, be sure that the selector is set to match the power at your location:

-115V, 60 Hz in most of North and South America and some Far Eastern countries

such as South Korea and Taiwan

- 100V, 50 Hz in eastern Japan and 100V, 60 Hz in western Japan

-230V, 50 Hz in most of Europe, the Middle East, and the Far East

•Be sure that attached devices are electrically rated to operate with the power available

in your location.

•Depending on your device, use only a supplied power adapter or approved power

cable:

If your device uses a power adapter:

-If you were not provided with a power adapter, contact your local NETGEAR

reseller.

-The power adapter must be rated for the product and for the voltage and current

marked on the product electrical ratings label.

If your device uses a power cable:

-If you were not provided with a power cable for your system or for any

AC-powered option intended for your system, purchase a power cable approved

for your country.

-The power cable must be rated for the product and for the voltage and current

marked on the product electrical ratings label. The voltage and current rating of

the cable must be greater than the ratings marked on the product.

Hardware Installation Guide8Introduction

8-Port Easy Mount Gigabit Ethernet PoE+ Smart Managed Plus Switch GS408EPP

•To help prevent electric shock, plug the system and peripheral power cables into

properly grounded electrical outlets.

•If applicable to your device, the peripheral power cables are equipped with

three-prong plugs to help ensure proper grounding. Do not use adapter plugs or

remove the grounding prong from a cable. If you must use an extension cable, use

a three-wire cable with properly grounded plugs.

•Observe extension cable and power strip ratings. Make sure that the total ampere

rating of all products plugged into the extension cable or power strip does not

exceed 80 percent of the ampere ratings limit for the extension cable or power strip.

•To help protect your system from sudden, transient increases and decreases in

electrical power, use a surge suppressor, line conditioner, or uninterruptible power

supply (UPS).

•Position system cables, power adapter cables, or power cables carefully. Route

cables so that they cannot be stepped on or tripped over. Be sure that nothing rests

on any cables.

•Do not modify power adapters, power adapter cables, power cables or plugs. Consult

a licensed electrician or your power company for site modifications.

•Always follow your local and national wiring rules.

Hardware Installation Guide9Introduction

8-Port Easy Mount Gigabit Ethernet PoE+ Smart Managed Plus Switch GS408EPP

Hardware Overview

This chapter describes the switch hardware features.

• Front panel

• Back panel and bottom panel

• Status LEDs

• Switch hardware interfaces

Otros manuales para GS408EPP

Tabla de contenidos

Otros manuales de Enrutador de red de NETGEAR

NETGEAR

NETGEAR JGS524FNA Manual de usuario

NETGEAR

NETGEAR D6200 Manual de usuario

NETGEAR

NETGEAR ProSAFE GS105Ev2 Manual de usuario

NETGEAR

NETGEAR GS748TS-100NAS Manual de usuario

NETGEAR

NETGEAR DG834GUV5 Manual de usuario

NETGEAR

NETGEAR Nighthawk R7000P Manual de usuario

NETGEAR

NETGEAR C6300 Manual de usuario

NETGEAR

NETGEAR GS748TNA Manual de usuario

NETGEAR

NETGEAR RP614 - Web Safe Router Manual de usuario

NETGEAR

NETGEAR Nighthawk X6 R7900 Manual de usuario

NETGEAR

NETGEAR FS605 v3 Manual de usuario

NETGEAR

NETGEAR DGN2200 - Wireless-N 300 Router Manual de usuario

NETGEAR

NETGEAR WNDR4300v2 Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

NETGEAR

NETGEAR WGT624v2 - 108 Mbps Wireless Firewall Router Manual de usuario

NETGEAR

NETGEAR ME101 - Wireless EN Bridge Network Converter Manual de usuario

NETGEAR

NETGEAR Nighthawk AX4 Manual de usuario

NETGEAR

NETGEAR Orbi RBW30 Manual de usuario

NETGEAR

NETGEAR BR500 Manual

NETGEAR

NETGEAR Nighthawk AXE1000 Manual de usuario

NETGEAR

NETGEAR RT311 Manual de usuario

NETGEAR

NETGEAR FVX538v1 - ProSafe VPN Firewall Dual WAN Manual de usuario

NETGEAR

NETGEAR RT338 Manual de usuario

NETGEAR

NETGEAR R6400 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad

LevelOne

LevelOne FBR-1416 Manual de usuario