NETGEAR FS102 Manual de usuario

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Congratulations on your purchase of the NETGEAR™Model FS102, Model FS104, or Model

FS108 Fast Ethernet Switch—a low-cost, high-performance network solution designed to support

power workgroups operating at 10 megabits per second (Mbps) or 100 Mbps.

In this installation guide that describes how to install and use the switches, all three switches are

referred to collectively as the Model FS102/FS104/FS108 switch. Each switch is listed

individually when information is provided that refers to a specific model.

The Model FS102/FS104/FS108 switch has the following features:

• Two (Model FS102 switch), four (Model FS104 switch), and eight (Model FS108 switch)

vista automatic speed-sensing 10/100 Mbps Ethernet ports that provide fast information

exchange, resource sharing, and client or peer-to-peer communication using standard

Category 5 unshielded twisted pair (UTP) cable

• Automatic address learning function to build the packet forwarding information table (The

table contains up to 8,000 MAC addresses; that is, the switch can support networks with as

many as 8,000 devices.)

• Autosensing full-duplex or half-duplex mode of operation (Full-duplex mode doubles

throughput of point-to-point connections by letting individual ports transmit and receive

concurrently when the connecting device also supports full-duplex mode.)

• Wire-speed filtering and forwarding to support the “traffic cop” function by directing traffic

to the appropriate port or network segment without slowing down the traffic

• Easy plug-and-play installation with no software to configure, which saves time and

minimizes the potential for configuration errors

• Normal/Uplink push button to simplify network extension (The switch can be connected to

another switch or hub using a standard, straight-through cable.)

• Two vista RJ-45 connector ports on the Model FS102 switch, four vista RJ-45 connector

ports on the Model FS104 switch, and eight vista RJ-45 connector ports on the Model FS108

switch (Each port has built-in LEDs to monitor individual port status.)

• LEDs that provide network traffic status and data transmission speed

• IEEE 8023u standard compliance, allowing incorporation with other 100BASE-TX Fast

Ethernet (100 Mbps) products

• IEEE 802.3 10BASE-T standard compliance

• Compact, sturdy metal case design that enables easy desktop, wall-mount, or under-desk

installation

Start Here

Features

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Verify that your package contains the following:

• Model FS102, Model FS104, or Model FS108 switch

• Mounting kit (for wall installation)

• This installation guide

• Warranty & Owner Registration Card

• Support Information Card

• AC power cord and universal power cord adapter

Package Contents

8900FA

Universal

power cord

adapter

Wall mount

installation kit

Installation guide,

Warranty & Owner

Registration Card,

and Support

Information Card

Model FS108 switch

Model FS102 switch Model FS104 switch

power

cord

12345678

234 56 78

Power Collision

100 Mbps LINK Rx

FS108

FAST ETHERNET SWITCH

FS102

FAST ETHERNET SWITCH LINK Rx

Collision

100 Mbps

1234

Power Collision

100 Mbps

FS104

FAST ETHERNET SWITCH LINK Rx

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Fast Ethernet Vista Ports with Built-in LEDs

All of the ports on the switch are 10/100 Mbps Ethernet ports. The network access speed for the

ports is automatically sensed and displayed on the front panel by the 100 Mbps LEDs.

Each port supports only unshielded twisted pair (UTP) cable using an 8-pin RJ-45 plug.

Each port uses vista RJ-45 connectors that have two LEDs—the Link LED and the FDX LED.

Product Illustration

8899FA

Front Panel of the Model FS102 switch

Front Panel of the Model FS108 switch

12345678

234 56 78

Power Collision

100 Mbps LINK Rx

FS108

FAST ETHERNET SWITCH

Power 2

FS102

FAST ETHERNET SWITCH LINK Rx

Collision

100 Mbps

100 Mbps ports

Normal/Uplink

push button

Power

Front Panel of the Model FS104 switch

1234

Power Collision

100 Mbps

FS104

FAST ETHERNET SWITCH LINK Rx

8724EB

Link

LED FDX

LED

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

LEDs

This table describes the activity of the Model FS102/FS104/FS108 switch LEDs.

Label Color Activity Description

Pwr (Power) Green On

Off Power is supplied to the switch.

Power is disconnected.

Rx/Tx/Collision Green

Yellow

Blinking

Packet transmission or reception is occurring on the port.

Data collisions are occurring on the port. The blinking action

corresponds to the number of collisions. When a collision

occurs, the connected device pauses and transmits again

after waiting a specified time. Note that occasional collisions

are normal.

100 Mbps Green On

Off

The port is operating at 100 Mbps.

The port is operating at 10 Mbps.

Link

(located at the

top left corner

of each vista

10BASE-T port)

Green On

Off

A valid link is established on the port.

A link is not established on the port.

FDX

(located at the

top right corner

of each vista

10BASE-T port)

Green On

Off

The port is operating in full-duplex mode.

The port is operating in half-duplex mode.

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Normal/Uplink Push Button

The Normal/Uplink push button on the front panel of the switch allows you to select uplink (MDI)

or normal (MDI-X) wiring for either of the Ethernet ports on the Model FS102 switch, port 4 on

the Model FS104 switch, or port 8 on the Model FS108 switch. These ports are configured for

normal wiring to connect to a PC when the push button position is out. When the push button is

pressed in, these ports are configured for uplink wiring to connect to another switch or to a hub,

using a straight-through twisted pair cable.

Rear Panel

The rear panel of the Model FS102/FS104/FS108 switch has full-duplex (FDX) and auto-duplex

(AUTO) toggle switches and a power adapter receptacle for the supplied power adapter.

FDX/AUTO Duplex Toggle Switches

Full-duplex mode is supported for all 10/100 Mbps ports and allows the port to transmit and

receive data at the same time. Full-duplex operation applies only to point-to-point access (for

example, when a switch is connected to a PC, a server, or another switch).

Setting the toggle switch to AUTO on the 10/100 Mbps port enables the port to determine duplex

mode automatically. In this mode of operation, the 10/100 Mbps port operates in either full- or

half-duplex, depending on the operating mode of the remote port. If the remote port cannot

provide the proper signal to indicate its capability, the 10/100 Mbps port on the switch defaults to

half-duplex mode. Repeaters and hubs use a common collision domain for all communications

and cannot communicate in full-duplex mode. The associated 10 Mbps port on the switch should

be set to auto-duplex operation when connecting to these types of devices.

One toggle switch is assigned to each 10/100 Mbps port and can be set to full-duplex (FDX) mode

or auto-duplex (AUTO) mode.

12Vdc 1.2A

– +

12Vdc 1.2A

– +

8901FA

Rear Panel of the Model FS102 switch

Rear Panel of the Model FS104 switch

Rear Panel of the Model FS108 switch

Power receptacle

14FDX

AUTO

10/100 Mbps

FDX -

AUTO - Force port to operate at Full Duplex and Half Duplex mode.

Enable port to determine duplex mode

automatically. Default is Half Duplex.

12Vdc 1.2A

– +

12345678FDX

AUTO

10/100 Mbps

FDX -

AUTO - Force port to operate at Full Duplex and Half Duplex mode.

Enable port to determine duplex mode

automatically. Default is Half Duplex.

12FDX

AUTO

10/100 Mbps

FDX -

AUTO - Force port to operate at Full Duplex and Half Duplex mode.

Enable port to determine duplex mode

automatically. Default is Half Duplex.

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

The Model FS102/FS104/FS108 switch is designed to provide flexibility in configuring your

network connections. Each switch can be used as a standalone device or can be used with 10 Mbps

or 100 Mbps hubs or other interconnection devices in various configurations. The configuration

examples in this section illustrate the integration of the switches in various network environments

using other NETGEAR products. These examples include a network of a few workstations

connected to a printer or a segmented network with multiple users or workgroups and other

networking devices.

Although the examples illustrate specific switches, any of the switches can be used in the network

configurations shown.

Desktop Switching

The Model FS108 switch is used as a desktop switch to build a small network that enables users to

have 100 Mbps access to a file server.

If a full-duplex adapter card is installed in the server or PC, a 200 Mbps connection is possible on

the port where the server or PC is connected.

Applications

12345678

234 56 78

Power Collision

100 Mbps LINK Rx

FS108

FAST ETHERNET SWITCH

Model FS108 switch

100 Mbps

10 Mbps

8902FA

Key

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Segment Switching

The Model FS108 switch is used as a switch that segments a network into multiple connected

pieces, increasing overall bandwidth and throughput. The Model FS108 switch can segment

networks that are built with the NETGEAR Model DS108 Dual Speed Hubs.

Extending a Network Diameter

Ethernet specifications limit the length of cable between hubs and PCs to 100 meters (m) for a

total of 200 meters. By adding Fast Ethernet switches between hubs, a network is expanded by 200

meters with the addition of each switch. The illustration below shows two NETGEAR Model

FE108 Fast Ethernet Hubs integrated with a Model FS108 switch to extend a network.

12345678

234 56 78

Power Collision

100 Mbps LINK Rx

FS108

FAST ETHERNET SWITCH

Auto 10/100 MbpsDUAL SPEED Auto 10/100 MbpsDUAL SPEED

Model FS108 switch

Model DS108 hubModel DS108 hub

8903FA

12345678

234 5678

Power Collision

100 Mbps LINK Rx

FS108

FAST ETHERNET SWITCH

Model FS108 switch

100 m

8904FA

Model FE108

hubs

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Bridging from 10BASE-T to 100BASE-TX Networks

The Model FS108 switch can function as a two-port bridge connecting traditional 10BASE-T

Ethernet networks to 100BASE-TX Fast Ethernet networks. Users requiring increased network

bandwidth can be upgraded to 100 Mbps while remaining connected to the rest of the network by

integrating the Model FS108 Fast Ethernet Switch with the NETGEAR Model EN108 Ethernet

Hub and the NETGEAR Model FE108 Fast Ethernet Hub.

High-Bandwidth File Servers

The Model FS104 switch increases bandwidth for workgroups and strengthens network

throughput when accessing high-volume file servers. The switch provides parallel communication

between each of the ports. This method of communication allows multiple conversations to occur

concurrently, expands overall throughput, and allows key servers or other heavily used devices to

be available to more users. The Model FS104 Fast Ethernet Switch can be integrated with a

NETGEAR Model FE108 Fast Ethernet Hub and a NETGEAR Model DS108 Dual Speed Hub. A

full-duplex configurable adapter card installed in the server provides up to 200 Mbps maximum

data throughput.

12345678

234 56 78

Power Collision

100 Mbps LINK Rx

FS108

FAST ETHERNET SWITCH

1234 56 78

Pwr

Col

EN108

10BASE-T HUB LINK Rx

Model EN108

hub

Model FE108 hub

8967FA

Model FS108 switch

200 Mbps

100 Mbps

10 Mbps

Key

Auto10/100 MbpsAuto10/100 Mbps DUAL SPEED

Model FS104

switch

Model FE108 hub Model DS108 hub

8906FA

Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide

Before you begin installing your switch, prepare the installation site. Make sure your operating

environment meets the operating environment requirements of the equipment.

To install your switch on a flat surface, you do not need any special tools. Be sure the switch is

positioned with at least 2 inches of space on all sides for ventilation.

To install the switch on a wall, measure the distance between the mounting holes on the back of

the switch and mark the wall to match the location of the mounting holes on the switch. At the

marks, screw into the wall the two screws in the mounting kit included in your package contents.

Choose a location that is near the devices to be connected, is close to an electrical outlet, and

provides at least 2 inches of space all around the switch for ventilation.

Before connecting the switch, be sure you review “Applications” for to determine the appropriate

configuration for your networking needs.

To connect the switch:

1. Connect the devices to the 10/100 Mbps ports on the switch, using Category 5 UTP

cable and an RJ-45 plug.

2. Set the Normal/Uplink push button.

The Normal/Uplink push button eliminates the need to use a crossover twisted pair cable for

daisy-chaining or cascading. Use the following guidelines to configure port 1 and port 2 on

the Model FS102 switch, port 4 on the Model FS104 switch, or port 8 on the Model FS108

switch for uplink or normal wiring:

• Configure the port for normal wiring if the port is to be connected to an uplink-wired

device, such as a network station or a PC.

• Configure the port for uplink wiring if the port is to be connected to a normal-wired

device, such as a 100 Mbps hub or another switch.

The remaining (normal) ports on the switch cannot be configured for uplink wiring. If you are

using one of these ports to connect to another normal port, you must use a crossover twisted

pair cable to connect the two ports. Refer to “Cable and Connector Information” for

information about crossover twisted pair cable and straight-through twisted pair cable.

Characteristic Requirement

Temperature Ambient temperature between 0

and 40

C (32

and 104

F).

No nearby heat sources such as direct sunlight, warm air exhausts, or

heaters.

Operating humidity Maximum relative humidity of 90%, noncondensing.

Ventilation Minimum 2 inches (5.08 cm) on all sides for cooling.

Adequate airflow in room or wiring closet.

Operating conditions At least 6 feet (1.83 m) to nearest source of electromagnetic noise (such

as photocopy machine or arc welder).

Power Adequate power source within 6 feet (1.83 m).

Note: Ethernet specifications limit the cable length between your PC or server and the

switch to 328 feet (100 meters).

Prepare the Site

Install the Switch

Connect Devices to the Switch

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador de red de NETGEAR

NETGEAR

NETGEAR N600 WNDR3400v2 Manual de usuario

NETGEAR

NETGEAR FVS328 - ProSafe VPN Firewall Manual de usuario

NETGEAR

NETGEAR FVX538v2 - ProSafe VPN Firewall Dual WAN Manual de usuario

NETGEAR

NETGEAR R6250 Manual de usuario

NETGEAR

NETGEAR JGS524FNA Manual de usuario

NETGEAR

NETGEAR DG834v2 - ADSL Modem Router Manual de usuario

NETGEAR

NETGEAR Nighthawk R7000P Manual de usuario

NETGEAR

NETGEAR Nighthawk X6 R7900 Manual de usuario

NETGEAR

NETGEAR Nighthawk X4 Guía de solución de problemas

NETGEAR

NETGEAR XE102 - Wall-Plugged EN Bridge Manual de usuario

NETGEAR

NETGEAR RH340 - ISDN INET Gateway Router Manual de usuario

NETGEAR

NETGEAR JWNR3000 Manual de usuario

NETGEAR

NETGEAR ProSafe FVS318N Manual de usuario

NETGEAR

NETGEAR C7800 Manual de usuario

NETGEAR

NETGEAR Nighthawk X4S R7800 Manual de usuario

NETGEAR

NETGEAR DG834GT - 108 Mbps Super G Wireless ADSL... Manual de usuario

NETGEAR

NETGEAR JNR3210 Manual de usuario

NETGEAR

NETGEAR WNHDE111 Manual de usuario

NETGEAR

NETGEAR JFS516GE Manual de usuario

NETGEAR

NETGEAR C6300 Manual de usuario

NETGEAR

NETGEAR Nighthawk AC1900 R7000 Manual de usuario

NETGEAR

NETGEAR WGR624v3 Manual de usuario

NETGEAR

NETGEAR PR2000 Manual de usuario

NETGEAR

NETGEAR R6400 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad

LevelOne

LevelOne FBR-1416 Manual de usuario