Netberg Aurora 750 Manual de usuario
The Aurora 750 switch
installation guide
The Aurora 750 switch installation guide
iii
Table of Contents
1. Introduction ........................................................................................................................ 1
2. Hardware Installation .......................................................................................................... 2
2.1. Installation Guidelines .............................................................................................. 3
2.2. Installation into a Rack ............................................................................................ 4
2.3. Installing Transceivers and cables into the Switch Ports ............................................ 6
2.3.1. SFP+/SFP28 Port Connection (LC Type Connector) ....................................... 6
2.3.2. QSFP+/QSFP28 Port Connection .................................................................. 7
2.4. Fan Modules ........................................................................................................... 8
2.5. Power supply .......................................................................................................... 9
2.5.1. Replacing a PSU .......................................................................................... 9
2.6. Connect the Power Cable ...................................................................................... 10
2.7. Grounding the Switch ............................................................................................ 11
2.8. Rack-mount Safety Precautions ............................................................................. 12
2.9. Console port ......................................................................................................... 13
2.10. Verifying Switch Operation ................................................................................... 14
3. Netberg Aurora 750 switch ............................................................................................... 15
3.1. Specification .......................................................................................................... 17
3.2. Supported Cables and Transceivers ....................................................................... 19
iv
List of Figures
2.1. Front brackets installation ................................................................................................ 4
2.2. Rack installation .............................................................................................................. 5
2.3. Transceivers and cables .................................................................................................. 6
2.4. Power Supply .................................................................................................................. 9
3.1. Aurora 750 front view .................................................................................................... 15
3.2. Aurora 750 rear view ..................................................................................................... 16
v
List of Tables
2.1. Console cable pin definition ........................................................................................... 13
3.1. Front panel features ...................................................................................................... 15
3.2. Rear panel features ....................................................................................................... 16
1
Chapter 1. Introduction
This guide is to assist the reader with the most basic form of installation and cable connection to
our switches. As there is more than one switch in the Aurora series, the actual port placement
might slightly differ, however, the installation and connection logic are the same for all Netberg
switches.
Package Contents:
• One Netberg Aurora Switch
• Two AC power cords.
• One RS-232-to-RJ45 console cable.
• One mini-USB console cable.
• One pair of frontal rack-mount brackets.
• Eight Phillips-head frontal rack-mount bracket screws.
If any of the above mention items was not found inside the package contents of this
switch or are damaged in any way, contact your reseller immediately.
2
Chapter 2. Hardware Installation
Hardware Installation
3
2.1. Installation Guidelines
This section will discuss the hardware installation guidelines that administrators must follow in or-
der to properly and safely install this switch into the appropriate environment.
Hardware Installation
4
2.2. Installation into a Rack
The switch can be mounted in a standard 19"(1U) rack using the provided mounting brackets.
The following section will explain how to install the rack-mount brackets onto the switch and then
mount the switch into a standard 2U rack-mount unit.
1. Use the supplied screws to attach a mounting bracket to each side of the Switch.
2. Align the holes in the mounting bracket with the holes in the rack.
3. Insert and tighten screws through each of the mounting brackets.
Figure2.1.Front brackets installation
1234567891
01
11
21
31
41
51
61
71
81
92
02
52
62
72
82
93
03
13
2
2
12
22
32
4
Auror a 710
R
ESET
PS1
PS2
F
A
N
SYS
E1
/33 E2/34
Two individuals are recommended to install the switch. One individual should position
the switch in the rack, while the other secures it using the rack screws.
The switch can be installed directly on the rack without the use of the rail.
1. Align the built-in mounting ear to the rack holes.
2. Tighten the screws to secure the switch.
Hardware Installation
5
Figure2.2.Rack installation
1234567891
01
11
21
31
41
51
61
71
81
92
02
52
62
72
82
93
03
13
2
2
12
22
32
4
Aurora 7 1 0
R
ESET
PS1
PS2
F
A
N
SYS
E1/33 E2/34
Illustrations are for reference purposes only. Actual switch and cabinet posts may dif-
fer.
Tabla de contenidos
Otros manuales de Cambiar de Netberg
