NetApp ASA A900 Manual de usuario

ASA A900 systems

Install and maintain

NetApp

July 28, 2023

This PDF was generated from https://docs.netapp.com/us-en/ontap-systems/asa900/install_setup.html on

July 28, 2023. Always check docs.netapp.com for the latest.

Table of Contents

ASA A900 systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Install and setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê1

Maintain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ê19

ASA A900 systems

Install and setup

Start here: Choose your installation and setup experience

You can choose from different content formats to guide you through installing and setting

up your new storage system.

•Quick steps

A printable PDF of step-by-step instructions with live links to additional content.

•Video steps

Video step-by-step instructions.

•Detailed steps

Online step-by-step instructions with live links to additional content.

Quick steps - ASA A900

This page provides graphic instructions for a typical installation of your system from

racking and cabling, through initial system bring-up. Use this content if you are familiar

with installing NetApp systems.

Access the Installation and Setup Instructions PDF poster:

AFF A900 Installation and Setup Instructions

The ASA A900 uses the same installation procedure as the AFF A900 system.

Video steps - ASA A900

There are two videos; one showing how to rack and cable your system and one showing

an example of using the System Manager Guided Setup to perform initial system

configuration.

Video one of two: Hardware installation and cabling

The following video shows how to install and cable your new system.

Animation - AFF A900 Installation and setup instructions

The ASA A900 uses the same installation procedure as the AFF A900 system.

Video two of two: Performing end-to-end software configuration

The following video shows end-to-end software configuration for systems running ONTAP 9.2 and later.

[] | https://img.youtube.com/vi/WAE0afWhj1c?/maxresdefault.jpg

Detailed steps - ASA 900

This page provides detailed step-by-step instructions for installing a typical NetApp

system. Use this article if you want more detailed installation instructions.

Step 1: Prepare for installation

To install your system, you need to create an account on the NetApp Support Site, register your system, and

get license keys. You also need to inventory the appropriate number and type of cables for your system and

collect specific network information.

You need to have access to the NetApp Hardware Universe for information about site requirements as well as

additional information on your configured system.

What you need

You might also want to have access to the ONTAP 9 Release Notes for your version of ONTAP for more

information about this system.

You need to provide the following at your site:

•Rack space for the storage system

•Phillips #2 screwdriver

•Additional networking cables to connect your system to your network switch and laptop or console with a

Web browser

Steps

1. Unpack the contents of all boxes.

2. Record the system serial number from the controllers.

3. Inventory and make a note of the number and types of cables you received.

The following table identifies the types of cables you might receive. If you receive a cable not listed in the

table, see the Hardware Universe to locate the cable and identify its use.

NetApp Hardware Universe

Type of

cable…

Part number and length Connector type For…

25 GbE data

Cable

X66240A-05 (112-00639),

0.5m

X66240A-2 (112-00598), 2m

X66240A-5 (112-00600), 5m

Network cable

32 Gb FC

(SFP+ Op)

X66250-2 (112-00342), 2m

X66250-5 (112-00344), 5m

X66250-15 (112-00346),

15m

FC optical network cable

40 GbE

network cable

X66100-1 (112-00542), 1m

X66100-3 (112-00543), 3m

X66100-5 (112-00544), 5m

Ethernet data, cluster

network

100 GbE

cable

X66211B-1 (112-00573), 1m

X66211B-2 (112-00574), 2m

X66211B-5 (112-00576), 5m

Network,

NVME storage,

Ethernet data,

cluster network

Optical

cables

X66031A (112-00436), 1m

X66032A (112-00437), 2m

X66033A (112-00438), 3m

FC optical network

Cat 6, RJ-45

(order

dependent)

Part numbers X6585-R6

(112-00291), 3m

X6562-R6 (112-00196), 5m

Management network and

Ethernet data

Micro-USB

console cable

Not applicable Console connection during

software setup on non-

Windows or Mac

laptop/console

Power cables Not applicable Powering up the system

4. Review the ONTAP Configuration Guide and collect the required information listed in that guide.

Step 2: Install the hardware

You need to install your system in a 4-post rack or NetApp system cabinet, as applicable.

1. Install the rail kits, as needed.

2. Install and secure your system using the instructions included with the rail kit.

You need to be aware of the safety concerns associated with the weight of the system.

3. Attach cable management devices (as shown).

4. Place the bezel on the front of the system.

The following diagram shows a representation of what a typical system looks like and where the major

components are located at the rear of the system:

Step 3: Cable controllers to your network

You can cable the controllers to your network by using the two-node switchless cluster method or by using the

cluster interconnect network.

Option 1: Two-node switchless cluster

Management network, data network, and management ports on the controllers are connected to switches.

The cluster interconnect ports are cabled on both controllers.

Before you begin

You must have contacted your network administrator for information about connecting the system to the

switches.

Be sure to check the direction of the cable pull-tabs when inserting the cables in the ports. Cable pull-tabs

are up for all networking module ports.

As you insert the connector, you should feel it click into place; if you do not feel it click,

remove it, turn it around and try again.

1. Use the animation or illustration to complete the cabling between the controllers and to the switches:

Animation - Cable a two-node switchless cluster

Step Perform on each controller

Cable cluster interconnect ports:

•Slot A4 and B4 (e4a)

•Slot A8 and B8 (e8a)

Step Perform on each controller

Cable controller management (wrench) ports.

Cable 25 GbE network switches:

Ports in slot A3 and B3 (e3a and e3c) and slot A9

and B9 (e9a and e9c) to the 25 GbE network

switches.

40GbE host network switches:

Cable host‐side b ports in slot A4 and B4 (e4b)

and slot A8 and B8 (e8b) to the host switch.

Cable 32 Gb FC connections:

Cable ports in slot A5 and B5 (5a, 5b, 5c, and 5d)

and slot A7 and B7 (7a, 7b, 7c, and 7d) to the 32

Gb FC network switches.

•Strap the cables to the cable management

arms (not shown).

•Connect the power cables to the PSUs and

connect them to different power sources (not

shown). PSU 1 and 3 provide power to all

side A components, while PSU2 and PSU4

provide power to all side B components.

Option 2: Switched cluster

Management network, data network, and management ports on the controllers are connected to switches.

The cluster interconnect and HA ports are cabled on to the cluster/HA switch.

Before you begin

You must have contacted your network administrator for information about connecting the system to the

switches.

Be sure to check the direction of the cable pull-tabs when inserting the cables in the ports. Cable pull-tabs

are up for all networking module ports.

As you insert the connector, you should feel it click into place; if you do not feel it click,

remove it, turn it over and try again.

1. Use the animation or illustration to complete the cabling between the controllers and to the switches:

Animation - Cable a switched cluster

B10

B11

A10

A11

6- 2

6- 1

a b c d

a b

6- 2

6- 1

Controller A

PSU 1

Controller B

PSU 2 PSU 3 PSU 4

abcd

a b c d

a b c d a b c d

a b

a b a b

abcd

abcdabcd

To cluster switches

34 4 3

To 25 GbE

network

switches

To host

network

switch

To 32 Gb

FC network

switches

To 32 Gb

FC network

switches

To 25 GbE

network

switches

To host

network

switch

2To management

network switches

Step Perform on each controller

Cable cluster interconnect a ports:

•Slot A4 and B4 (e4a) to the cluster network

switch.

•Slot A8 and B8 (e8a) to the cluster network

switch.

Cable controller management (wrench) ports.

Tabla de contenidos

Otros manuales de Sistema de matriz de discos de NetApp

NetApp

NetApp E Series Manual de usuario

NetApp

NetApp AFF A220 Manual de usuario

NetApp

NetApp E2760 Manual de usuario

NetApp

NetApp AFF A300 Manual de usuario

NetApp

NetApp AFF A700s Manual de usuario

NetApp

NetApp FAS2700 Series Manual de usuario

NetApp

NetApp AFF A900 Manual de usuario

NetApp

NetApp FAS Manual de usuario

NetApp

NetApp AFF A900 Manual de usuario

NetApp

NetApp EF Series Manual

NetApp

NetApp AFF A700 Manual

NetApp

NetApp FAS2600 Manual de usuario

NetApp

NetApp AFF Manual de usuario

Manuales populares de Sistema de matriz de discos de otras marcas

Fujitsu

Fujitsu ETERNUS DX60 S2 Manual de usuario

Accom

Accom WSD/2XTREME Manual de usuario

HP Compaq Presario,Presario 4400 Instrucciones de uso

ATTO Technology

ATTO Technology Diamond Storage Array V-Class Manual de usuario

National Instruments

National Instruments RMX-8268 Manual de usuario

Overland Tandberg

Overland Tandberg SnapServer DX1 Manual de usuario

easyRAID

easyRAID Q08QA-2GR2 Manual de usuario

NEC

NEC NF2300-SR412E Manual de usuario

EMC

EMC iomega StorCenter px12-350r Manual de usuario

Infortrend

Infortrend EonStor A08U-C2411 Manual de usuario

SE Audiotechnik

SE Audiotechnik M-F3 Manual de usuario

Buffalo

Buffalo HD-QHU3R5 Manual de usuario

HP StorageWorks XP128 Manual de usuario

Addonics Technologies

Addonics Technologies Z4SN25NML Manual de usuario

HP StorageWorks P2000 Guía

HP 4400 Enterprise Manual de usuario

G-Technology

G-Technology G-RAID2 Manual de usuario

HP STORAGEWORKS XP24000 Manual de usuario