Nero Radio 8113 UPMi Manual de usuario
1
Single-channel radio receiver Radio 8113 UPMi
Manual
434 MHz, 230 V AC, max 5 A
5
P
3
L
124
N
1 General information
1.1 Application
The receiver Radio 8113 UPMi is designed to control motors of roller shutters and roller
shade.
1.2 Features
?possibility to program transmitters without the programming button on the receiver’s housing;
?convenient side location of contacts;
?possibility to connect an extra one-button switch by any producer.
1.3 Technical characteristics
Working range, MHz..............................................................................................................................................434,42 ± 0,37
Switching current,max À.........................................................................................................................................................3
Number of motors for operation .............................................................................................................................................1
Memory (number of transmitters), pcs ...............................................................................................................................500
Duration of commands “UP”, “DOWN”, sec......................................................................................................................100
Duration of command “Comfort”, sec. .................................................................................................................................7
Dimensions, mm.........................................................................................................................................................51?51?29
Working temperature......................................................................................................................................from 0 to + 45°Ñ
Working conditions .................................................................................................................................dry heated buildings
IP protection class ...............................................................................................................................................................IP20
1.4Installation and connection of the Radio 8113 UPMi
b)
INSTALLATION
BOX
RADIO 8113 UPMi
ONE-BUTTON
SWITCH
à)
?Unpack the Radio 8113 UPMi receiver.
?Follow the connection scheme on Fig.1b to install the receiver Radio 8113 UPMi..
?Use double-sided skotch tape to fix the Radio 8113 UPMi receiver inside the
installation box.
?Screw the one-button switch to the installation box.Contacts description:
1 — connect to UP direction cable of the motor;
2 — connect to DOWN direction cable of the motor;
3 — connect to L of the ~230 V power line;
4 — connect to N of the ~230V power line;
5 — connect to the one-button switch.
WALL
Radio 8113 UPMi
345
12
One-button
switch
Motor
Fig. 1 à) Installation of the 8113 UPMi; b)connection of the Radio 8113 UPMi to the motor.
2 Programming the Radio 8113 UPMi receiver
2.1 Enter the programming mode:
?Way 1: press and hold > 4 sec. the switch button or a button of the transmitter that has been previously programmed until
the motor stops (if it was working) or rolls up and down;
?Way 2: activate the motor (up or down), stop it and in 3 sec. press the switch or touch the programmed transmitter button
five times (the motor will indicate that the programming mode is activated by making an up and down movement).
Note No.1
?If the receiver’s memory is empty, then, the Radio 8113 UPMi will enter the programming mode automatically when it will be
connected to the motor and power line.
?If the motor has end strokes, one should reach the end postition of the roller shutter and then press the switch shourtrly or touch the
programmed transmitter button 5 times.
2.2 Programming transmitter codes into the Radio 8113 UPMi:
?when transmitters Radio 8133-9, Radio 8101-5 are used one should touch the STOP button of the transmitter;
?when transmstters Radio 8101-2, Radio 8101-4 are used one should touch the button that needs to be programmed.
The motor will indicate that the programming was successful by the following motions:
Note No. 2
?If the transmitter you want to programmed has been previously programmed, the motor will indicate this as follows:.
?If the receiver’s memory is full, the motor will indicate this as follows:
2.3 Leave the programming mode:
touch the switch or the previously programmed button of the transmitter.
The motor will indicate the disactivation as follows:
Note No. 3
PThe receiver will automatically leave the programming mode if one doesn’t perform any actions within 32 sec.
PTo delete the button of the transmitter, press this button > 1 sec. after entering the programming mode (p.2.1).
PTo erase the memory completely hold the switch button or the previously programmed button more than 4 sec.
3 Operation by means of the Radio 8113 UPMi receiver
4 Storage
Store the receiver packaged in dry buildings at temperature 0-25 C.
The receiver can make the roller shutter to perform the following commands:
?”UP”, “DOWN”, “COMFORT” if transmitters Radio 8133-9, Radio 8101-5 are used;
?”UP”, “DOWN” if transmitter Radio 8152-50 is used;
?Step-by-step (up-stop-down) if transmitters Radio 8101-1, Radio 8101-2; Radio 8101-4are used;
?”UP”, “DOWN”, Step-by-step if a switch is used.
5 Warranty
The warranty period is 24 months. Please, don’t throw away the manual as it is the warranty certificate.
qpqqppqp
qpqp
qp
qpqpqp
www.neroelectronics.com
Tabla de contenidos
