Nemtek Druid D2 Series Manual de usuario

Instruction Manual for Druid D2x

NEMTEK Connect

Device Gateway 2G

Foreword

Thank you for choosing our product. The NEMTEK Connect Device Gateway 2G is designed

and manufactured to provide many years of reliable use, if installed and maintained correctly.

The guidelines provided in this manual will assist you with the basic operation and maintenance

of your unit. Currently this product is designed and manufactured in South Africa for South African

and international markets. More information on our products and general information is available

on our website at: http://www.nemtek.com

The NEMTEK Connect Device Gateway 2G provides connectivity to your supported NEMTEK

devices by allowing for connectivity to the NEMTEK Connect platform. Together with the

NEMTEK Connect App, you can remotely monitor and control your NEMTEK devices, as well

as receive notifications and alerts.

Supported Nemtek Devices

The NEMTEK Connect DG works with the following Nemtek products:

Druid D25, D28

Note: This list may be changed without prior notice.

Please see the hardware installation section for more details on how to set up your specific device.

Hardware Overview

The NEMTEK Connect DG features:

2G GSM GPRS Modem

Nano SIM Card slot

SMA (Female) Connector, supports many SMA (Male) GSM Antennas

D2x comms support for Nemtek Druid D2x range

www.nemtek.com

Board Connections

Energizer

Power Out

Antenna

Connector

User

Button

User LEDs

SIM

Card

Slot

To Energizer

Comm Port

www.nemtek.com 2

To Energizer

Battery

Hardware Installation

The NEMTEK Connect DG has been designed to be installed onto the battery brace inside

of the enclosure of a supported NEMTEK energizer.

To install the DG, unplug the energizer from mains and disconnect the energizer’s battery

leads from the battery. You may need to remove the battery brace to get better access to

the battery terminals to remove and plug in the cables onto the battery terminals.

Plug the energizer battery leads directly into the Battery Power Out terminals of the DG

board. Be careful to ensure you connect the correct polarity wires to the correct terminal.

Make sure the terminal connectors are plugged in completely and firmly onto the battery

terminals on the board.

Connect the furthest away battery wire to the battery. This is usually the negative terminal

and wire, unless the battery is orientated differently. Take care to ensure you connect the

correct polarity wires to the correct battery terminals. Do not connect the second wire yet,

as this will apply power to both the DG and energizer.

Make sure the battery is firmly in place and screw the battery brace back over the battery.

Be sure that no wires or obstacles are between the battery brace and the battery and that

the battery brace goes over the battery without any force, otherwise this may cause a crack

in the battery which could cause a leak of battery acid.

Align and screw in the DG board on the battery brace. Two screws are supplied for this

purpose.

Screw in the antenna. If your antenna has a lead, make sure it is routed outside of the

enclosure via the appropriate cable management ports, be careful to not get the cable caught

on the enclosure edge when screwing the lid back on.

Connect up the DG to your energizer as is necessary (see following section for details for

each of the supported Nemtek products).

Once everything is wired up and setup, plug in the second lead to the battery to power up

the system. Screw the lid of the enclosure back into place and plug the energizer back into

the mains. Reconnect the mains supply.

www.nemtek.com

C2 C3 C4 C5

S4 S5

Connecting to Supported Nemtek Products

Connecting to a Druid D2x Energizer

The Druid D2x (D25 and D28) is connected to the NEMTEK Connect DG via the data

ribbon cable included.

Connect the ribbon to the relevant connectors on the DG and the energizer.

Set the energizer up to network address number 1 using the keypad. This is done by entering

programming mode (INSTALLER_PIN*#) and the address change command (5101#),

then exit programming mode (*#).

LED Definitions

Flashes Description:

0 GSM is off

1 Searching for network

2 CSD Signal acquired

3 GPRS connection established --

Performing server connection process

4 Connected to Server

5 SIM Error Condition

www.nemtek.com 4

+—

Energizer

Battery Leads

Data

Ribbon Cable

CDGD2X 10/22 Rev.1.0

www.nemtek.com

GUARANTEE & DISCLAIMER

The NEMTEK Connect DGM, manufactured by NEMTEK (Pty) Ltd, is guaranteed for a period of two years

from date of sale against defects due to faulty workmanship or materials. NEMTEK will, at its discretion,

either repair or replace a product that proves to be defective. NEMTEK guarantees that the product, when

properly installed and used in line with the specification as determined by NEMTEK from time to time,

will execute its function of generating a suitable potential.

NEMTEK (Pty) Ltd does not guarantee that the operation of the product will be uninterrupted and totally

error free. Faulty units must be returned to one of the NEMTEK Group outlets. The buyer shall pay all

shipping and other charges for the return of the product to NEMTEK or NEMTEK Security Warehouse.

Specifications may be altered without prior notification.

LIMITATION OF GUARANTEE

The guarantee does not apply to defects resulting from acts of God, modifications made by the buyer or

any third party, misuse, neglect, abuse, accident or mishandling.

EXCLUSIVE REMEDIES

The remedies provided herein are NEMTEK (Pty) Ltd’s sole liability and the buyer’s sole and exclusive

remedies for breach of warranty. NEMTEK shall not be liable for any special, incidental, consequential,

direct or indirect damages, whether based on contract, tort, or any other legal theory. The foregoing

guarantee is in lieu of any and all other guarantees, whether expressed, implied, or statutory, including

but not limited to guarantees of merchantability and suitability for a particular purpose.

COMPANY PROFILE

The NEMTEK Group of Companies manufacture and distribute intelligent electronic agricultural fencing

systems, security and perimeter control systems and have been involved in the security industry since

1990. We have our own research and development team, designing and manufacturing a full range of

globally competitive electric fence energizers and related products. NEMTEK is continually updating its

products according to South African and international standards in order to ensure the highest quality

products and continuous customer satisfaction.

Tabla de contenidos

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario