Nemtek FG7C Guía del usuario
INSTALLERS MANUAL
Revision 1.3
11 December 2018
GROUP OF COMPANIES
FG7
C
CONTROLLER
for DRUID 25/28 NETWORKS
2
FG7C CONTROLLER:
Table of Co te ts
INTRODUCTION…..……………………………………………………………………… 3
OPENING THE FG C…...………………………………………………….……………. 3-4
HARDWARE….................................................................................. 5
INSTALLING THE FG C…………………………………………………………………. 6-
THE DISPLAY BOARD……………………………………………………………………. 8-9
COMMUNICATION BOARDS…………………………………………………………… 10-12
PROGRAMMING THE FG C ……….……………..…………………………………… 12-16
MAPPING…………………………………………………………………………………….. 1 -20
FIRMWARE UPGRADE…………………………………………………………………… 20
THE FG WEB INTERFACE…………………………………………………………….. 21-22
THIRD PARTY INTEGRATION………………………………………………………… 22
DOCUMENT REVISION HISTORY……………..…………………………………….. 23
3
FG7C CONTROLLER: I troductio
INTRODUCTION
The Nemtek FG platform is a platform used for providing a graphical interface and connectivity
to a network of Nemtek Energizers and Input/Output Cards (IO Cards).
The platform may be configured with different internal printed circuit boards, and software, to
provide the required functionality.
War i g:
Test the functionality of the system after configuration and before commissioning.
OPENING THE FG7C
Pa el mou t type
On one of the long sides of the FG C are two slots. Insert a 6.5mm screw driver into one of the
slots and turn the screw driver until the lid with the display pops up on that side. Now repeat this
with the other slot. You should now be able to carefully remove the lid.
4
FG7C CONTROLLER: OPENING THE FG7C
Wall mou t type
On one of the long sides of the FG C are two openings with retaining clips. Insert a 6.5mm screw
driver into the bottom part of one of the openings and push the retainer clip back until the lid
with the display pops up on that side. Now repeat this with the other opening. You should now
be able to carefully remove the lid.
5
FG7C CONTROLLER: HARDWARE
HARDWARE
The lid of the FG C contains a green printed circuit board IOT1 11JM and a dark blue control
unit as well as the touch screen.
The IOT1 11JM board is responsible for generating the supply voltage for the control unit as well
as the display. The board also monitors and process the different communication signals before
sending the information to the control unit.
Under the dark blue control unit is the battery which is required for the clock during power
failures.
You will find jumpers, connectors and led’s on the board for selecting, connecting and indicating.
The control unit host the software and has all communication ports on board.
The touchscreen is the standard display used on the stand-alone units, without Druid FenceProbe
or third party software.
In the base of the FG C a communication board has to be installed, there are two communication
boards available.
The FG7C commu icatio board with Nemli k/Taut wire
6
FG7C CONTROLLER: I stalli g the FG7C
The FG7C commu icatio board with RS485/Taut wire/TTL
INSTALLING THE COMMUNICATION BOARD
The communication board should be mounted in the bottom of the base of the FG C with the
screws supplied with the board. The terminals on the board should be facing inwards once
mounted.
After mounting, the ribbon cables of the display board should be connected to the two white
terminals on the communication board (con1 and con2)
INSTALLING THE WALL MOUNT FG7C
The base of the FG C has several counter sunk mounting holes at bottom of the unit, these can
be used to mount the unit on a wall with 4mm screws. The holes are spaced 100 x100 mm or 5
x 5 mm so that the unit can also be mounted at the back of HD monitor if so required.
Cable entries are available by means of a pushout at the bottom of the base or two cut outs on
the side of the base.
INSTALLING THE PANEL MOUNT FG7C
The panel mount FG C is designed to be mounted flush in wooden walls or dry walling. A cut out
has to be made in these walls of 195mm x 130 mm.
Before installing the base of the FG C into the wall make sure that all cut outs required for the
wiring are done on the base, that the wiring to the FG C is fully tested and that the
communication board is installed.
The base is supplied with two wing clamps (see picture), make sure that they are positioned in
their base cavities. Place the base into the opening in the wall making sure that the cabling will
not get in the way of the wing clamps. Turn the top wing clamp screw a quarter turn anti
clockwise before turning it clockwise until the clamp is tight. Repeat this for the bottom clamp.
The base should now be securely clamped into the wall. Before closing the lid ensure that all
programming and all wiring to the control board and communication board is completed.
7
FG7C CONTROLLER: I stalli g the FG7C
FG7C CONTROLLER: I stalli g the
commu icatio boa
If removal of the base is required then first remove the lid from the base and disconnect the
wiring between the lid and the base, so that it can be fully removed. Turn the top wing clamp
screw anti clockwise until the wing clamp comes back into its base cavity (do not fully unscrew
the wing clamp screw since it will detach and can fall inside the wall). Repeat for the bottom
wing clamp and remove the base from the wall opening.
Wing clamp and Wing clamp screw
8
FG7C CONTROLLER: THE DISPLAY BOARD
THE DISPLAY BOARD
JUMPER SETTINGS DISPLAY BOARD
Jumper setting as viewed with connectors at the bottom.
Watch Dog timer 1 JP1 (1)
Positioned to the left for auto reset of the power supply with
transmission failure of the control unit
Positioned to the right for no auto reset of the power supply
Watch Dog timer 2 JP3 (1) Positioned to the left for auto reset with transmission failure of
the control unit
Positioned to the right for no auto reset of the control unit
PUSH BUTTONS ON DISPLAY BOARD
There are two push buttons on the green board. The one is marked SW2 “5V_RESET” and the
other SW1 “B3_RESET”. The 5V_RESET button is used to manually power the control unit on and
off, this is usually required when programming the settings on the FG C. The B3 RESET button is
used to manually reset the FG C control unit.
9
FG7C CONTROLLER: THE DISPLAY BOARD
LED’S ON DISPLAY BOARD
LED1 Shows that the FG C is On
LED2 5V supply indicator
LED3 When flashing, indicates that the watchdog timer is operational
LED4 Not in use
CONNECTORS
Con 1 Ribbon cable connection to Con1 of communication board
Con 2 Ribbon cable connection to Con2 of communication board
Con 3 Not in use
USB PORT
The USB port is used for downloading logs and can also be used for a mouse, so that a pointer
can be used on the touch screen display.
HDMI PORT
The HDMI port is a standard micro-HDMI connector. The activation of the HDMI port can be
done via the web interface (see the FG web interface). A USB mouse connected to the USB port
of the FG should be used for operating the system when using an HDMI display or the USB port
can be used for the touch screen part of a touch screen monitor. The resolution of the display if
possible should be set to 1920 x 1080. The picture of the site image should be 1000 x 650 pixels.
ETHERNET PORT
The Ethernet port is used for communication with a computer loaded with Druid FenceProbe or
third party software and it is also used for connecting to the web interface of the FG .
Note:
The control unit hosts the software and gives outputs via the touch screen, HDMI, Ethernet or
USB port. All other ports should not be used by the installer.
10
FG7C CONTROLLER: COMMUNICATION BOARDS
THE NEMLINK/TAUT WIRE COMMUNICATION BOARD
JUMPER SETTINGS COMMUNICATION BOARD
Jumper setting as viewed with connectors at the bottom.
Nemlink programming JP3 (1) Down to enable programming of the Nemlink
Up standard operational mode
LED’S ON COMMUNICATION BOARD
LED1 If flashing, indicates receiving of data from the Nemlink to the control
unit.
LED2 If flashing, indicates transmission of data from the control unit to the
Nemlink
LED3 If flashing, indicates receiving of data from the taut wire to the control
unit
LED4 If flashing, indicates transmission of data from the control unit to the
taut wire
LED5 5V supply indicator
CONNECTORS
Con 1 Ribbon cable connection to Con1 of display board
Con 2 Ribbon cable connection to Con2 of display board
Con 3 Ethernet port for connection to data network
J1 Two way connector for 12Vdc supply
J6 Three way connector for connection to the taut wire system
Tabla de contenidos
Otros manuales de Controladores de Nemtek
