NEC NP3150CM Guía

Este manual sirve para los siguientes modelos

10

Tabla de contenidos

Otros manuales de Rack y soporte de NEC

NEC

NEC WM-46UN Wall Mount Portrait and Landscape Manual de usuario

NEC

NEC WM-55UN-L Manual de usuario

NEC

NEC WMK-3255S Manual de usuario

NEC

NEC N8140-820 Manual de usuario

NEC

NEC NP-M260W Guía

NEC

NEC IW77 Manual de usuario

NEC

NEC PA600CM Manual de usuario

NEC

NEC WMK-3257 Guía

NEC

NEC 92679B/W Manual de usuario

NEC

NEC LCD8205 - MultiSync - 82" LCD Flat Panel... Manual de usuario

NEC

NEC NP01UCM Manual de usuario

NEC

NEC Wall Mount PDW S 32-55 P (WMS 32-55 P Manual de usuario

NEC

NEC Video Wall Mount PDVWXUN 55 P Manual de usuario

NEC

NEC NP-P350W Guía

NEC

NEC NP04WK1 Guía

NEC

NEC N8143-93 Manual de usuario

NEC

NEC PlasmaSync PX-60XM5A Manual de usuario

NEC

NEC N8154-46 Manual de usuario

NEC

NEC Wall Mount PDWXS 46 55 L (WM-46S-L) Manual de usuario

NEC

NEC LCD3215 - MultiSync - 32" LCD Flat Panel... Manual de usuario

NEC

NEC N8143-56F/56E Manual de usuario

NEC

NEC NP600CM Guía

NEC

NEC NEC W32-70 Manual de usuario

NEC

NEC PD04VW QR 46 55 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario

5880 Sheridan Boulevard, Arvada, Colorado 80003

Ph: 303-412-0399 ▪Fax: 303-412-9346

www.displaydevices.com



NECDisplaySolutionsofAmerica,Inc.



InstallationandAssemblyManual:

CustomCeilingMountforNECNP1000,NP2000,NP1150,NP2150,

NP3150,NP3151W,NP1250,NP2250,NP3250,andNP3250WProjectors



Model:NP3150CM

Ceiling Mount

1. Remove ¼”-20 button head bolt on ceiling plate to remove lower portion of mount.

2. Install the ceiling plate with (4) 5/16” bolts to structural attachment points. Lag screws

may be used when attaching to wood joists.

3. Reattach the lower portion of the mount.

4. Attach interface plate (pn 72-061) to projector with (4) M4 x 10 pan head Phillips screws.

5. Align interface plate into holes on mount, slide stand off bolts into slots and tighten. Add

center locking Torx cap screw which attach secures the interface plate to the mount.

6. Attach the wire safety rope to the interface plate with the enclosed coupler.

7. Attach power and signal cables to projector.

8. Attach the I/O cover (pn 72-065) to the interface plate with (4) 10-32 x 3/8 pan head

Phillips screws and #10 lock washers.

9. Loosen tilt adjustment cap screw with enclosed tool and level the projected image to the

screen. Tighten cap screw when a level image is achieved.

10. Loosen up-down pitch adjustment cap screw with enclosed tool and adjust the pitch

angle of the projector. Tighten cap screw when at desired projection position.

11. If desired, add Kensington lock through the opening of the mount head, loop through

cable end and attach to projector.

5880 Sheridan Boulevard, Arvada, Colorado 80003

Ph: 303-412-0399 ▪Fax: 303-412-9346

www.displaydevices.com

Pole Mount

1. Install a 1 ½” NPT pipe with male threads on lower end from the ceiling. Aftermarket

mounting pans and accessories are available.

2. Thread locking ring onto pipe. Thread mount onto pipe and leave locking ring loose.

3. Attach interface plate (pn 72-061) to projector with (4) M4 x 10 pan head Phillips screws.

4. Align interface plate into holes on mount, slide stand off bolts into slot and tighten. Add

center locking Torx cap screw which attach secures the interface plate to the mount.

5. Attach the wire safety rope to the interface plate with the enclosed coupler.

6. Insert power and signal cables through pipe and out the top of the mount head to the

projector and attach to projector.

7. Attach the I/O cover (pn 72-065) to the interface plate with (4) 10-32 x 3/8 pan head

Phillips screws and #10 lock washers.

8. Adjust left-to-right yaw. When desired position is attained, tighten locking ring on pipe

to mount.

9. Loosen tilt adjustment cap screw with enclosed tool and level the projected image to the

screen. Tighten cap screw when a level image is achieved.

10. Loosen up-down pitch adjustment cap screw with enclosed tool and adjust the pitch

angle of the projector. Tighten cap screw when at desired projection position.

11. If desired, add Kensington lock through the opening of the mount head, loop through

cable end and attach to projector.