NCR 7701-K134 Manual de usuario
Kit Instructions
4GB Memory Upgrade
7701-K134
Issue B
The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. Product names mentioned in this publication may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is
permitted under the terms and conditions of an agreement you have with NCR, NCR's copyright notice
must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components,
software, and firmware become available. NCR, therefore, reserves the right to change specifications
without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this
document, consult with your NCR representative or NCR office for information that is applicable and
current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity,
organization, and value of this book. Please use the link below to send your comments.
Email: FD230036@ncr.com
Copyright © 2017–2019
By NCR Corporation
Global Headquarters
864 Spring St NW
Atlanta, GA 30308
U.S.A.
All Rights Reserved
Revision Record
Issue Date Remarks
AFeb 2017 First Issue
BNov 2019 Added CX5 (7773)
4GB Memory Upgrade
This kit provides a memory upgrade for the following POS:
• NCR XR3 POS (7613)
• NCR XR4 POS (7602)
• NCR XR5 POS (7701)
• CX5 All-in-One POS (7773)
Kit Contents
Warning: Disconnect the AC power cord before disassembling the Terminal.
Caution: Static Electricity Discharge may permanently damage your system. Discharge
any static electricity build up in your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and handle cards only by their external
edges.
2 Memory Upgrade
Installation Procedure
XR3 POS (7613) / XR4 POS (7602)
1. Open the Base. If a Cable Management Bar is present, loosen the captive screws (2)
and remove the Bar.
2. Remove the screws (3) securing the Bottom Cover.
Note: An HDD storage media may be installed on the Bottom Cover, do not remove
the HDDscrews while the Cover is still mounted on the Base.
Memory Upgrade 3
3. Remove the front Rubber Feet (2) from the Cover.
4. Carefully rotate the Cover backward to open the Base. If an HDD storage media is
installed, remove its Data and Power connectors from the motherboard.
a. With HDD Storage Media
4 Memory Upgrade
b. With SSD Storage Media
5. Install the memory upgrade in the right–hand socket (Socket 2).
6. To install a module, align it with the socket and push it into the socket.
Memory Upgrade 5
7. Press the module down until it latches in position. Make sure that the edges of the
module engage the latches and that the latches are completely engaged.
XR5 POS(7701)
1. Remove the Rear Cover.
a. Loosen the captive screws (2) that secure it to the chassis.
b. Pivot the Rear Cover as shown.
6 Memory Upgrade
2. The optional Hard Disk Drive is mounted on the inside of the Rear Cover. If an HDD
is present, disconnect the HDDPower and Data cables from the motherboard.
3. To install a module, align it with the socket and push it into the socket (the socket is
keyed).
4. Press the module down until it latches in position. Make sure that the edges of the
module engage the latches and that the latches are completely engaged.
Memory Upgrade 7
CX5 All-in-One POS (7773)
Note: Memory configurations containing a single memory module should be installed
in the lower socket (Socket 1). Memory can be expanded by installing a second module
in the upper socket (Socket 2).
1. Lay the Display face down on a flat surface.
Note: Always use a soft material (cloth, foam) to protect the display screen when
placing the terminal face down.
2. Remove the Cable Cover.
a. Remove the two (2) screws that secure the Cable Cover to the Back Cover.
b. Rotate and unhook the Cable Cover from the Back Cover.
8 Memory Upgrade
3. Disconnect the Cables.
a. Loosen the thumbscrew of the 180-degree USB-C Cable then disconnect the
Cable.
b. Remove the Ethernet Cable from the Cable Management Hook then disconnect
the Cable.
4. Remove the two (2) captive screws that secure the Back Cover to the Display.
Tabla de contenidos
Otros manuales de Unidad de control de NCR
NCR
NCR 7358-K580 Manual
NCR
NCR 7358-K111 Manual de usuario
NCR
NCR K150 Instrucciones de funcionamiento
NCR
NCR 7606-K132 Manual
NCR
NCR 7358-K704 Manual
NCR
NCR 7403-K150 Manual de usuario
NCR
NCR 7197 SII Manual de usuario
NCR
NCR 7703-K168 Manual de usuario
NCR
NCR personaS84 ATM Manual de usuario
NCR
NCR 7403-K131 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
