NComputing L-Series Manual de usuario
1
2
NComputing would like to thank you for purchasing this product.
©2005-2007 NComputing, Inc. All rights reserved. Specifications subject to change without notice.
NComputing® is the property of NComputing and may be registered in Korea and other countries.
Other trademarks and trade names are the property of their respective owners.
Refer to the following to prevent any physical injury or loss of assets caused by damage to the product.
A user must read this User's Guide carefully before use and follow the instructions.
•Please make sure that the place of installation is not too hot (above 35˚C) ,too cold (below
0˚C), or too wet.
•Please keep the case safe from any severe impact.
•Please make sure that the product does not come into direct contact with benzene or thinner.
•Please make sure that the product is not exposed to direct sunlight or any hot machinery.
•Please keep the product away from any items which have strong magnetic properties.
•Please do not disassemble, repair or rebuild the product.
•Please do not leave a LAN (Local Area Network) cable in any passageway. An electric shock,
fire, damage to the product or physical injury may occur as a result of tripping over the cable.
•Please disconnect the LAN cable from the product when the cable is not in use for a long period
of time.
•Please install the product so it is safe from damage caused by dropping or falling.
FCC Information
This equipment has been tested and found to comply with the limit for a class B digital device,
pursuant 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct the interference by one or
the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
•Consult the dealer or an experienced radio TV technician for help
Change or modification not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment
3
MIC
인증사항
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
•기기의 명칭(모델명) : Multi-User Computing Access Terminal (L230)
•인증 번호 : NCC-L230 (B)
•인증 받은 자의 상호 : 엔컴퓨팅 주식회사
•제조자/제조국가 : 엔컴퓨팅 주식회사/한국
•제조년월 : 제품 뒷면 참고
NCC-L230 (B)
•기기의 명칭(모델명) : Multi-User Computing Access Terminal (L130)
•인증 번호 : NCC-L130 (B)
•인증 받은 자의 상호 : 엔컴퓨팅 주식회사
•제조자/제조국가 : 엔컴퓨팅 주식회사/한국
•제조년월 : 제품 뒷면 참고
NCC-L130 (B)
•기기의 명칭(모델명) : Multi-User Network Terminal (L120)
•인증 번호 : NCC-L120 (B)
•인증 받은 자의 상호 : 엔컴퓨팅 주식회사
•제조자/제조국가 : 엔컴퓨팅 주식회사/한국
•제조년월 : 제품 뒷면 참고
NCC-L120 (B)
•기기의 명칭(모델명) : Multi-User Network Terminal (L200)
•인증 번호 : NCC-L200 (B)
•인증 받은 자의 상호 : 엔컴퓨팅 주식회사
•제조자/제조국가 : 엔컴퓨팅 주식회사/한국
•제조년월 : 제품 뒷면 참고
NCC-L200 (B)
이 기기는 가정용으로 전자파 적합 등록을 한 기기로서 주거지역에서는 물론 모든 지역에서
사용할 수 있습니다.
4
Notice
This product has been made by using state of the art technology from NComputing and has undergone
thorough testing, An understanding of reliability has been reached for this product due to the extensive
testing.
This User's Guide is designed to help the user to achieve easy installation and use of the product. Our
company makes every effort to provide our customers with information related to the product, and with
answers for any questions that may be asked by our customers. The performance of the product can be
continuously enhanced via the software update utility.
(Please refer to the relevant section of the User's Guide for more detailed information).
The customer's registration and the registration of the product serial number, which can be done via the
Internet, enables customers to receive the software upgrade service and ongoing technical support via
the Internet for their convenience.
Please note that reproduction of the User's Guide in whole or in part, without permission from the
manufacturer, is not permitted.
Please read the notes, which are related to safety, before use.
The information in the User's Guide may vary depending on any improvements in the product and the
model type of the purchased product.
The manufacturer is not responsible for any damage to the product that is caused by using any products
which are not specified as standard products, or by not following instructions and procedures correctly.
This product is compatible with Windows and Linux.
Any other operating systems including new operating systems require special software, which can be
purchased separately, or an upgrade of the software is available at extra cost.
This product is an independent terminal device that provides for the emulation of Windows. It is not a
computer. Unlike an existing computer there is no need for the addition of auxiliary peripheral devices,
or for the connection of a different types of communication devices, or for the modification of
hardware. Some of the products may not support images with high color depth or 3D games that are
supported by high performance computers.
Please refer to the Windows operating system for more detailed information.
5
TABLE OF CONTENTS
FCC Information......................................................................................................................... 2
Notice.......................................................................................................................................... 4
TABLE OF CONTENTS............................................................................................................ 5
What is the access terminal?........................................................................................................ 6
What is the terminal services software?...................................................................................... 6
Features....................................................................................................................................... 6
Minimum System Requirements................................................................................................. 6
Conceptual Diagram.................................................................................................................... 7
Installation................................................................................................................................... 7
Install the terminal services software (optional, but must be done once) ........................................ 7
Connect the Access Terminal.................................................................................................... 11
Before............................................................................................................................11
After..............................................................................................................................11
Network connection......................................................................................................11
Installation with monitor mount (L130 and L230 only).....................................................13
Product Registration.................................................................................................................. 14
Online Registration..........................................................................................................16
Offline Registration.......................................................................................................17
Uninstallation................................................................................................................19
Updating the Terminal Services Software....................................................................19
Using the access terminal..............................................................................................19
Configure the Access Terminal.....................................................................................19
The access terminal screen............................................................................................19
Using the management console.....................................................................................23
Software Settings (local)...............................................................................................24
Sessions......................................................................................................................... 24
Information & Settings..................................................................................................26
USB-Device Assignment(s)..........................................................................................29
Software Settings (LAN) ..............................................................................................30
Hardware Settings (LAN/local)....................................................................................31
Troubleshooting error messages...................................................................................33
Error messages on the access terminal..........................................................................33
DHCP server was not found..........................................................................................33
No Terminal Server found or not all services initialized yet, please click on
the connection list and try it again................................................................................33
Host unreachable….......................................................................................................34
TS ERROR – INVALID OR NO SERIAL NUMBER!...............................................34
Connection was closed but your data is not lost and application is still running on
the server. Please connect to the terminal sever later. ..................................................34
Authorization error........................................................................................................35
TS ERROR – Stations Limit Exceeded !......................................................................35
Troubleshooting error messages on the Host PC..........................................................35
Multi user Error.............................................................................................................35
Glossary ........................................................................................................................35
FAQ...............................................................................................................................37
6
What is the access terminal?
The L-series access terminals enable you to dramatically cut computing costs by sharing the untapped power of
PCs. The access terminals, Ethernet-based extension protocol, and terminal services software work together to
efficiently harness excess computing capacity and enable multiple users to share a single PC. Best of all, IT staff
and end users do not need special training because this end-to-end solution is easy to manage and is compatible
with standard PC applications.
What is the terminal services software?
Note: This document uses the following terms interchangeably: "User software," "host PC software," "terminal
services software," and "NCT-2000-XP".
NCT-2000-XP, the terminal services software, divides the host PC's resources into independent sessions that
give each user their own robust PC experience. One PC can support up to ten users when running on a desktop
operating system, such as Microsoft Windows XP. With a server operating system on the host (Microsoft
Windows 2003 Server or Linux), up to 30 users can be supported simultaneously. NComputing terminal service
software also works with the optional NControl and NShield software that add more centralized management
capabilities such as remote monitoring and host PC data backup.
Features
The L-series access terminals do not have a CPU, hard drive or CD-ROM, yet most users find it
indistinguishable from a full PC environment. The L-series exclusive technology allows you to add up to 30
computing terminals to your existing PC. Each access terminal offers a full and independent computing
experience.
Simultaneous desktop operation
Each access terminal accesses the host PC OS and can run its applications concurrently and independently
through Ethernet.
Minimal Maintenance Required
You only have to maintain and upgrade the host PC since the access terminals have no CPU, hard drive, or CD-
ROM.
Small sleek design
Allows more room in your office or on your desk, and can even mount on the back of your LCD with included
bracket.
Eco-friendly
Since the access terminals have no moving parts, it makes no noise and saves energy by drawing only 5 watts.
Supports multiple resolutions
640x480, 800x600, 1024x768 and 1280x1024, by 16-bit colors.
Additionally, the L130 supports 1440x900 by 16-bit colors and the L230 supports 1440x900 by 24-bit
colors.
New Feature: Microphone
The L230 now includes a microphone port.
Minimum System Requirements
A host PC with at least:
•A 2 GHz processor
7
•512 MB RAM
•60 GB hard disk drive
•Ethernet switch or router
Do not use a notebook PC as the host. Notebooks use power-saving features and different technologies than a
typical desktop PC, and this causes power management and memory problems.
Conceptual Diagram
Installation
Install the terminal services software (optional, but must be done once)
Insert the Software Installation CD into the host PC's CD drive.
In most cases, a window will automatically appear after a few seconds with installation options. If it doesn't
appear after 2 minutes, go to "My Computer", open the CD drive's icon, and start the "Setup" application.
At the installation screen, click on the "Install Program" button.
Before the installation starts, the installation software attempts to connect to the Internet to compare the software
version on the CD with the latest software version on the NComputing server. If there is a later version on the
NComputing server, a prompt will appear to ask if you want to use the version on the CD or if you want to
install the latest version. It is recommended to install the latest version rather than use an older version on the
CD.
8
Note: The following message will appear if any computer on the network is not connected to the Internet or a
program such as a firewall blocks the port.
The following ports should be opened on the LAN: TCP Ports 27605, 3581, 3597, 3645, 3646, 3725; UDP Ports
1027, 1283 (these are subject to change).
At the "Welcome" screen, click on the "Next" button.
At the antivirus and firewall warning screen, click on the "Next" button.
At the software license screen, you may view the software license and print it out. When you are finished, click
on the "I agree" checkbox, then click on the "Next" button.
9
At the software terms of use screen, you may view the software terms of use document and print it out. When
you are finished, click on the "I agree" checkbox, then click on the "Next" button.
At the readme file screen, you may view the readme file and print it out. When you are finished, click on the
"Next" button.
At the "Choose destination location" screen, you can install to the default location, or you can choose a different
location. When you are finished, click on the "Next" button.
At the "Choose Password for Administrator" screen, select whether or not to use an administrator password and
whether or not to install the Network Administration Console. If you choose to use an administrator password,
enter it and retype it. Click on the "Next" button.
10
Note: The Network Administration Console allows you to administer the terminal service software and the
access terminals in your network. It is recommended to be installed at least once on each network to enable
administration tasks. It may be installed on every terminal service software installation.
At the installation confirmation screen, review the selections and click on the "Next" button.
The software is installed.
At the "Add new users" screen, select whether or not you would like to add new users to the system. If you click
on the "Yes" button, the installation program will launch a screen to administer user accounts on the host PC. If
you click the "No" button, the installation process will continue without bringing up the user administration
screen.
Note: It is recommended that all users have their own user accounts to enable control of their own settings.
Tabla de contenidos
Otros manuales de Terminal táctil de NComputing
