NBB SR8299 Manual de usuario
Assembly Instructions
Shelter Type: SR8299
SR8299-01-28102021-USA
14
15
10
14
10 11
1
4
4
11
9
5
5
9
2
8
16
17
6
7
3
15
12
14
14
2
EXPLODED VIEW
3
PARTS LIST
ITEM
NO.
PART
NO.
DESCRIPTION
Size (inch)
IMAGE
QTY.
1
S1
Full Frame
78.74 x 40.74
5
2
CB1
Corner Bracket - CB1
4.3 x 4.3 x 1.57
8
3
JF1
Joint Flat - JF1
4.33 x 1.57
7
4
P1
Post Frame - P1
78.74 x 40.74
2
5
ST5
ST5 Roof Tie Bar
60.75 2
6
P5
P5 POST
77.15 x 1.57 x
1.57 1
7
JFT
Bracket
8.66 x 5.9
1
8
DR
Rafter Bracket
4.3 x 1.6 x 2
12
9
DR2R
DR2R Rafter
92.32 4
10
DR2I
DR2 infill panel
85 x 15.75
2
11
DR2PO
DR2 Roof Panel Outer
92.32 x 41.54
2
12
DR2PI
DR2 Roof Panel Inner
40.75 x 92.30
1
13
DR2T
DR2 Roof Trim
92.32 x 3.15
4
14
DRATO
DR Ally-Angle Trim Outer
2 x 2 x 41.5
4
15
DRATI
DR Ally-Angle Trim Inner
2 x 2 x 40.75
2
16
FT1
FT1 BRACKET
1.57 x 1.57 x
3.94 5
17
FT3
FT3 Bracket
1.57 x 3.15 x
4.17 4
18
EC40
Plastic end cap
1.6 x 1.6
6
4
FIXINGS
Tools required:
Drill/Screwdriver
Mallet
17mm Wrench
T25 Torx bit
Fittings
Bolt set M10
T25 T38
BTANCM12100
M10 x 60mm
Nut
Washer
1" Tech
screw
1.5"
Tech
screw
Black
Caps
M10/12 x 100 mm
Concrete Bolt
Pack A+B
33 33 66 136 40 66 11
Image
MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
Please note 1.5" Tec Screws
are for roof panels only
CB1
CB1
CB1
CB1
CB1
CB1
JF1 JF1
CB1
CB1
JF1
P1
P1
ST5
JF1 JF1
JFT
ST5
P5
ENSURE CORRECT
ALIGNMENT ON
CORNERS
JF1
CB1 CB1
CB1
JF1
JF1
JF1JF1
JFT
DETAIL A
SCALE 1 : 10
DETAIL B
SCALE 1 : 10
DETAIL C
SCALE 1 : 10
DETAIL D
SCALE 1 : 10
Step 1
Assemble
S1
frames to make up the main structure using
CB1
brackets for the corners and
JF1
brackets for the straight joints.
Attach
P1
post to the S1C Frame using
CB1
and
JF1
brackets.
Brackets as shown below.
5
DR2R
DR2I
DR BRACKET
DR2I
DR2R
DR2R
DR2R
40.75 40.75 40.75
RAFTER PLACEMENT
6
Step 2
Attach
DR2R
rafters using
DR
brackets. Secure the
END PANELS (DR2I)
to frames
using tec screws. The end rafters need to be placed in position at the same
time as the
DR2I
DR2PO
DR2PO
DR2T DR2T
DR2T
DRATO
DRATO
DRATO
DRATO
DRATI
DRATI
DR2T
DR2PI
7
Step 3
Attach the
DR2PO and DR2PI
Panels to the top of the rafters, with the
DR2PO
on either end and the
DR2PI
in between. Seal the gap between the panels
using the
DR2T
strips. Attach the
DRATO and DRATI
Trim parts to the lower part
of the rafters as shown below.
FT1 x5
FT3 x4
8
Step 4
Move the shelter into its desired position and attach the foot brackets
FT1/FT3
before fixng in place.
40.75 81.87
39.17
41.12
38.27
77.44
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 8" oversized on all 4 sides.
9
10
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water
•
Ensure all fittings are tight (for example after a big storm)
•
Touch up any exposed metal should it get scratched
•
CONTACT DETAILS:
Email : [email protected]
Web : www.nobutts.com
Tel : 1-888-662-8887
No Butts Bin Company, Inc. 16 Birch Lane, Madison, CT 06443
All Parts and Fixings checked by:
Print Name:
Signature:
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Refugio de NBB
NBB
NBB SR8306 Manual de usuario
NBB
NBB SR8061-F Manual de usuario
NBB
NBB SR8062-F Manual de usuario
NBB
NBB Hilton NUB012 Manual de usuario
NBB
NBB SR8303-F Manual de usuario
NBB
NBB SR8302 Manual de usuario
NBB
NBB SR8303 Manual de usuario
NBB
NBB SR8301-F Manual de usuario
NBB
NBB SR8300 Manual de usuario
NBB
NBB SR8302-F Manual de usuario
