NBB SR8064-F Manual de usuario
Assembly Instructions
Shelter type: SR8064-F
SR8064F-01-03112021-USA
7
7
17
8
14
5
11
10
10
4
4
19
2
1
14
17
9
18 16
16
9
3
5
6
6
2020
20
2
Exploded View
3
PARTS LIST
ITEM
NO.
PART NUMBER
DRG number
Size (inch)
IMAGE
QTY.
1
S1C Frame
SC1
78.74 x 40.74
9
2
Post P1
P1
78.75 x 40.5
1
3
JF1 Bracket
JF1
4.33 x 1.57
12
4
FT1 BRACKET
FT1
1.57 x 1.57 x 3.94
3
5
DR Bracket
DR
4.3 x 1.6 x 2
16
6
AR2R 2m Pitch Rafter
AR2R
85.75 5
7
AR2POA AR2 Roof
Panel outer ALU
AR2POA
45.5 x 41.3
4
8
AR2IS 2m Pitch Infill
Panel Shallow
AR2IS
85 2
9
AR2TS 2m Apex Roof
Trim strip
AR2TS
45.5 x 2.3
6
10
FT3 Bracket
FT3
1.57 x 3.15 x 4.17
8
11
CB1 Bracket
CB1
4.3 x 4.3 x 1.57
9
12
Roof centre lower
trim outer
AR2CLTO-03
41.4 2
13
Roof centre lower
trim inner
AR2CLTI-02
40.74 2
14
Roof F Section
Outer
ARFSO
41.5 4
15
ARFSI Apex Roof F
Section Inner
ARFSI
40.75 4
16
AR2PIA AR2 Roof
Panel inner ALU
AR2PIA
45.5 x 40.5
4
17
Roof centre upper
trim outer
AR2CUTO-02
41.5 2
18
Roof centre upper
trim inner
AR2CUTI
40.75 2
19
ST3 Roof Tie
ST3
81.1 1
20
40x40 Plastic End
Cap
EC40
1.6 x 1.6
3
4
FIXINGS
83
164.6
MEASURE THE WIDTH AND DEPTH
OF THE SHELTER TO CHECK
CORRECT ALIGNMENT.
Please note 1.5" Tech Screws
are for roof panels only
S3C
CB1
JF1
Ensure correct
alignment on all corners
CB1
JF1
Step 1
Assemble
S1C
frames to make up the main structure using
CB1
brackets for the corners and
JF1
brackets for the straight joints.
5
ST3
CB1
P1
JF1
ST3
P1
Step 2
Use
JF1
and
CB1
brackets to attach the
P1
post and
ST3
Tie bar .
6
AR2IS
AR2IS
AR2R
AR2R
AR2R
AR2R
AR2R
DR
DR
DR
DR
DR
DR
DRDR
40.75 40.75 40.75 40.75
FRONT VIEW
Step 3
Attach
A2R2
rafters unsing
DR
brackets. Secure the
AR2IS
End Panels to
the frames using Tech Screws. The end rafters need to be placed in position at the
same time as 1" the
AR2IS
.
7
AR2CLTO
AR2CLTIAR2CLTI
ARFSO
ARFSO
ARFSI
ARFSO
ARFSO
ARFSI
AR2CLTO
ARFSI
ARFSI
AR2CLTO
ARFSO
ARFSO
ARFSI
ARFSI
ARFSO
ARFSO
AR2CLTI
ARFSI
ARFSI
AR2CLTI
AR2CLTO
Attach the
AR2CLTI
and
AR2CLTO
to the top of the rafters. The
ARFSI
and
ARFSO
parts are to be attached to the lower part of the rafter as shown
below.
8
Step 4
AR2POA
AR2TSAR2TSAR2TSAR2TS
AR2POA
AR2POI
AR2POA
AR2POA
AR2POI
FT3
FT1
FT3
AR2CUTO
AR2CUTO
AR2CUTI
FT1
AR2CUTI
AR2PIOAR2PIO
Align the outer roof panels
AR2POA
with the outer edges of the shelter and
space the
AR2PIA
panels central. Use the
AR2TS
strips to seal the gap
between the roof panels and cap off the top with the
AR2CUT2.
Once the
shelter is in the final position it can be secured to the ground using
concrete bolts and brackets
FT3/FT1
.
9
Step 5
83
164.6
10
PLAN VIEW
OVERALL DIMENSIONS AND GROUND FIXING POSITIONS
Suggested size for concrete base: 8" oversized on all 4 sides.
Tabla de contenidos
Otros manuales de Refugio de NBB
NBB
NBB SR7901 Manual de usuario
NBB
NBB SR7901-F Manual de usuario
NBB
NBB SR8300 Manual de usuario
NBB
NBB SR8306 Manual de usuario
NBB
NBB SR8061-F Manual de usuario
NBB
NBB SR8303-F Manual de usuario
NBB
NBB SR8299 Manual de usuario
NBB
NBB SR8062-F Manual de usuario
NBB
NBB SR8304-F Manual de usuario
NBB
NBB SR8306-F Manual de usuario
