National Instruments NI 9871 Manual de usuario

OPERATING INSTRUCTIONS AND SPECIFICATIONS

NI 9871

4-Port, RS485/RS422 Serial Module

NI 9871 Operating Instructions 2 ni.com

This document describes how to use the National Instruments 9871

and includes specifications and pin assignments for the NI 9871.

Visit ni.com/info and enter rdsoftwareversion to determine

which software you need for the modules you are using. For

information about installing, configuring, and programming the

system, refer to the system documentation. Visit ni.com/info and

enter cseriesdoc for information about C Series documentation.

Note The safety guidelines and specifications in this

document are specific to the NI 9871. The other

components in the system might not meet the same safety

ratings and specifications. Refer to the documentation for

each component in the system to determine the safety

ratings and specifications for the entire system. Visit

ni.com/info and enter cseriesdoc for information

about C Series documentation.

Safety Guidelines

Operate the NI 9871 only as described in these operating

instructions.

Hot Surface This icon denotes that the component may be

hot. Touching this component may result in bodily injury.

Safety Guidelines for Hazardous Locations

The NI 9871 is suitable for use in Class I, Division 2, Groups A, B,

C, D, T4 hazardous locations; Class I, Zone 2, AEx nA II T4 and

Ex nA II T4 hazardous locations; and nonhazardous locations only.

Follow these guidelines if you are installing the NI 9871 in a

potentially explosive environment. Not following these guidelines

may result in serious injury or death.

Caution Do not disconnect I/O-side wires or connectors

unless power has been switched off or the area is known

to be nonhazardous.

Caution Do not remove modules unless power has been

switched off or the area is known to be nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Zone 2 applications, install the

CompactRIO system in an enclosure rated to at least

IP 54 as defined by IEC 60529 and EN 60529.

NI 9871 Operating Instructions 4 ni.com

Caution For Zone 2 applications, install a protection

device between the RS485/RS422 signal cables and the

NI 9871 RJ-50 jacks (ports 1–4). The device must

prevent the RS485/RS422 signal-to-signal or

signal-to-COM voltage from exceeding 23 V if there is a

transient overvoltage condition.

Caution For Zone 2 applications, install a protection

device between the external power supply and the

NI 9871 Vsup and COM pins. The device must prevent the

Vsup-to-COM voltage from exceeding 39 V if there is a

transient overvoltage condition.

Special Conditions for Hazardous Locations in Europe

This equipment has been evaluated as Ex nA IIC T4 equipment

under DEMKO Certificate No. 07 ATEX 0626664X. Each module

is marked II 3G and is suitable for use in Zone 2 hazardous

locations. If you are using the NI 9871 in Gas Group IIC hazardous

locations or in ambient temperatures of –40 °C ≤Ta ≤70 °C, you

must use the device in an NI chassis or controller that has been

evaluated as EEx nC IIC T4, Ex nA IIC T4, or Ex nL IIC T4

equipment.

Special Conditions for Marine Applications

Some modules are Lloyd’s Register (LR) Type Approved for

marine applications. To verify Lloyd’s Register certification, visit

ni.com/certification and search for the LR certificate, or

look for the Lloyd’s Register mark on the module.

Caution To meet radio frequency emission requirements

for marine applications, use shielded cables and install

the system in a metal enclosure. Suppression ferrites

must be installed on power supply inputs near power

entries to modules and controllers. Power supply and

module cables must be separated on opposite sides of the

enclosure and must enter and exit through opposing

enclosure walls.

NI 9871 Operating Instructions 6 ni.com

Wiring the NI 9871

The NI 9871 has four RJ-50 receptacles that provide connections

for four RS485/RS422 devices.

Table 1. RS485/RS422 Port Pinout

RJ-50 Pin Signal Name*

1No Connect

2TXD–

3TXD+

4RTS–

5CTS–

6RXD–

7RXD+

8RTS+

9CTS+

10 GND

* These signals are shared by all four RJ-50 connectors on the NI 9871.

RJ50 Jack

TXD–

TXD+

RTS–

CTS–

RXD–

RXD+

RTS+

CTS+

COM

The cables included with your kit convert the RJ-50 pinout to the

standard NI pinout, as shown in Table 2.

Table 2. Pin Assignments for RS485/RS422 DB-9 Male Connector

Connector Pin Signal

1GND

2CTS+

3RTS+

4RXD+

5RXD–

6CTS–

7RTS–

8TXD+

9TXD–

NI 9871 Operating Instructions 8 ni.com

You must connect an external power supply to the NI 9871.

This power supply provides the power for the RS485/RS422

transceivers on the module. You can use the included female

four-position pigtail to connect to an external voltage source.

Figure 1 lists the connections between an external voltage source

(of +8 V to +28 V) and the NI 9871.

Figure 1. Four-Position External Power Connector

SUP 2V

SUP 3COM 4COM

Figure 2 shows the method of power connection to the NI 9871

module. Attach an isolated power supply to the Vsup and COM

terminals using the included pigtail.

Figure 2. Powering the NI 9871 from an Isolated Power Source

Figure 3 shows how to use the optional y-adapter (available at

ni.com/serial) to connect power to more than one module

using the same power source. One y-adapter is needed for each

Red (+)

Black (–)

NI P/N 198159-XX:

Female Microfit

Pigtail

V+

V–

Any 8 - 28 V

Isolated

Power Supply

NI 9871 Operating Instructions 10 ni.com

additional module. Ensure that the power supply can handle

maximum power requirements for all modules connected.

Caution All connections must be made before power is

applied.

Figure 3. Powering Multiple Modules from a Single Power Supply

Red (+)

Black (–)

NI P/N 198303-XX:

Male Microfit

Y-Adapter

NI P/N 198159-XX:

Female Microfit

Pigtail

V+

V–

Any 8 - 28 V

Isolated

Power Supply

Otros manuales para NI 9871

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Tarjeta de red de National Instruments

National Instruments

National Instruments DAQCard-1200 Manual de usuario

National Instruments

National Instruments NI 781xR Manual de usuario

National Instruments

National Instruments NI 9481E Manual de usuario

National Instruments

National Instruments NI 9264 Manual de usuario

National Instruments

National Instruments NI 9472 Manual de usuario

National Instruments

National Instruments Module SCXI-1125 Manual de usuario

National Instruments

National Instruments NI PXI-1056 Manual de usuario

National Instruments

National Instruments NI 6509 Manual de usuario

National Instruments

National Instruments AutoCode NI MATRIX Manual de servicio

National Instruments

National Instruments NI 9219 Manual de usuario

National Instruments

National Instruments MXI Series Manual de usuario

National Instruments

National Instruments NI 9234 Manual de usuario

National Instruments

National Instruments IMAQ PCI-1410 Manual de usuario

National Instruments

National Instruments NI PCI-6110 Manual de usuario

National Instruments

National Instruments Graphical User Interface Ultiboard Manual de usuario

National Instruments

National Instruments NI 9233 Manual de usuario

National Instruments

National Instruments NI 9215 Manual de usuario

National Instruments

National Instruments NI-XNET Manual de usuario

National Instruments

National Instruments Isolated Current Output Module SCC-CO20 Manual de usuario

National Instruments

National Instruments NI 9425 Manual de usuario

National Instruments

National Instruments Module SCXI-1503 Manual de usuario

National Instruments

National Instruments Measure Data Acquisition Manual de usuario

National Instruments

National Instruments NI 9481 Manual de usuario

National Instruments

National Instruments NI 9401 Manual de usuario

Manuales populares de Tarjeta de red de otras marcas

FirstComm

FirstComm OBiWiFi5G Manual de usuario

Sun Microsystems

Sun Microsystems Interface Adapter Manual de usuario

TRENDnet

TRENDnet TU2-ETG Manual de usuario

YASKAWA

YASKAWA SI-EN3 Manual de usuario

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manual de usuario

Belkin

Belkin F5D7050 Manual de usuario

3Com

3Com EtherLink 3C509B Manual de usuario

TRENDnet

TRENDnet TEG-PCITX Manual de usuario

Cisco

Cisco MC16E Manual de usuario

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manual de usuario

TwinMOS

TwinMOS Booming Manual de usuario

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manual de usuario

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manual de usuario

Hama

Hama 49276 Manual de usuario

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manual de operación

Compaq

Compaq Wireless LAN 100 Manual de usuario

Bose

Bose PowerMatch Dante Manual de usuario

TRENDnet

TRENDnet TEG-PCITXR Manual de usuario