National Instruments CP400X Manual de usuario

CP400X

GETTING STARTED GUIDE

PXIe-5163

PXIe, 200 MHz, 1 GS/s, 14-bit PXI Oscilloscope

Note Before you begin, install and configure your chassis and controller.

This document explains how to install, configure, and test the PXIe-5163. The PXIe-5163 is a

200 MHz, 1 GS/s oscilloscope.

Documentation for the PXIe-5163 is available from the Start menu by navigating to

NI-SCOPE Documentation in the National Instruments folder.

Contents

Verifying the System Requirements..........................................................................................2

Unpacking the Kit..................................................................................................................... 2

Other Equipment....................................................................................................................... 3

Preparing the Environment....................................................................................................... 4

Installing the Software.............................................................................................................. 4

Installing the PXIe-5163........................................................................................................... 5

PXIe-5163 Front Panel and Pinout .......................................................................................... 7

PXIe-5163 SCB-19 Pinout..............................................................................................10

PXIe-5163 Mini-HDMI Breakout Cable to 6 BNC Pinout.............................................11

Configuring the PXIe-5163 in MAX...................................................................................... 12

PXIe-5163 Self-Calibration.................................................................................................... 12

Running Self-Calibration................................................................................................ 13

First Measurements................................................................................................................. 13

Making a Measurement with InstrumentStudio..............................................................13

Making a Measurement with LabVIEW.........................................................................14

PXIe-5163 Compensating Passive Probes...................................................................... 14

Programming the PXIe-5163.................................................................................................. 16

NI-SCOPE Examples......................................................................................................18

Troubleshooting...................................................................................................................... 19

Why Is the ACCESS LED Off When the Chassis Is On?...............................................19

What Should I Do if the PXIe-5163 Doesn't Appear in MAX?......................................19

What Should I Do if the PXIe-5163 Fails the Self-Test?................................................20

Where To Go Next.................................................................................................................. 21

Worldwide Support and Services............................................................................................ 21

Verifying the System Requirements

To use the NI-SCOPE instrument driver, your system must meet certain requirements.

Refer to the product readme, which is available on the driver software media or online at

ni.com/manuals, for more information about minimum system requirements, recommended

system, and supported application development environments (ADEs).

Unpacking the Kit

Refer to the following figure to identify the contents of the PXIe-5163 kit.

Figure 1. PXIe-5163 Kit Contents

13 4 52

16-BitIF Digitizer

NI PXIe-5163

1. PXIe-5163

2. PXIe-5163 Safety, Environmental, and Regulatory

Information

3. PXIe-5163 Getting Started Guide (this document)

4. Maintain Forced-Air Cooling Note to Users

5. Export Requirements Note to Users

Notice To prevent electrostatic discharge (ESD) from damaging the module,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the module from the package and inspect it for loose components or other signs

of damage.

Notice Never touch the exposed pins of connectors.

Note Do not install a module if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the module in the antistatic package when the module is not in use.

2| ni.com | PXIe-5163 Getting Started Guide

Other Equipment

There are several required items not included in your device kit that you need to operate the

PXIe-5163. Your application may require additional items not included in your kit to install or

operate your device.

Required Items

• A PXI Express chassis and chassis documentation

• A PXI Controller or PC with a Device for PXI Remote Control system that meets the

system requirements specified in this guide and chassis documentation

Optional Items

• PXI Slot Blocker Kit, 5 slot blockers (NI part number 199198-01)

• PXI Filler Panel Kit, 17 filler panels (NI part number 778646-01)

• BNC-to-BNC cable, 50 Ω, 1 m (NI part number 781887-01)

• AUX 0 connectivity:

– SCB-19 noise rejecting, shielded AUX 0 connector block (NI part number

783959-01)

– SHH19-MH19-AUX shielded single-ended cable, 1 m (NI part number 784091-01)

– Mini-HDMI Breakout Cable to 6 BNC, 6 in. (NI part number 786979-01)

• Oscilloscope probe compensator, SMB (NI part number 786983-01)

• Probes—refer to the following table for several options compatible with the PXIe-5163.

Table 1. Probe Options for the PXIe-5163

Model NI Part Number Description

CP400X 784254-01 400 MHz, 2 m, 10X cable divider probe

CP500X 784253-01 500 MHz, 1.2 m, 10X cable divider probe

NI 5191 781785-01 800 MHz differential active probe

SA1000X 784255-01 1 GHz single-ended active probe

SA1500X 784256-01 1.5 GHz single-ended active probe

SA2500X 784257-01 2.5 GHz single-ended active probe

SP500C 783630-01 100x passive probe, 500 MHz

SP500X 783629-01 10x passive probe, 500 MHz

CC0550X 786846-01 5 A RMS, 50 MHz current probe

CC05120X 786847-01 5 A RMS, 120 MHz current probe

PXIe-5163 Getting Started Guide | © National Instruments | 3

Table 1. Probe Options for the PXIe-5163 (Continued)

Model NI Part Number Description

CC5002X 786848-01 500 A RMS, 2 MHz current probe

CC15010X 786849-01 150 A RMS, 10 MHz current probe

CC3050X 785561-01 30 A RMS, 50 MHz current probe

CC30100X 785562-01 30 A RMS, 100 MHz current probe

Visit ni.com for more information about these additional items.

Preparing the Environment

Ensure that the environment in which you are using the PXIe-5163 meets the following

specifications.

Temperature

Operating 0 °C to 50 °C

Storage -40 °C to 71 °C

Humidity

Operating 10% to 90%, noncondensing

Storage 5% to 95%, noncondensing

Pollution Degree 2

Maximum altitude 4,600 m (570 mbar) (at 25 °C ambient temperature)

Indoor use only.

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Visit ni.com/downloads/drivers and search for NI-SCOPE.

3. Download the latest version of NI-SCOPE, extract the downloaded files, and run the

executable (.exe) file.

Driver support for the PXIe-5163 was first available in NI-SCOPE 18.7.

4. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

4| ni.com | PXIe-5163 Getting Started Guide

5. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

Installing the PXIe-5163

Notice To prevent damage to the PXIe-5163 caused by ESD or contamination,

handle the module using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the module.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the module.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic covers from all the captive screws on the module front panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

PXIe-5163 modules can be placed in PXI Express peripheral slots, PXI Express hybrid

peripheral slots, or PXI Express system timing slots.

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the downward (unlatched) position.

8. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the module into the slot until it is fully inserted.

PXIe-5163 Getting Started Guide | © National Instruments | 5

Figure 3. Module Installation

16-BitIFDigitizer

NIPXIe-5163

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Downward (Unlatched) Position

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the module front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

11. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize

cooling air flow, depending on your application.

12. Power on the chassis.

6| ni.com | PXIe-5163 Getting Started Guide

PXIe-5163 Front Panel and Pinout

Front Panel

PXIe-5163

200 MHz Oscilloscope

ACCESS ACTIVE

CH 0

CAT II TO

50 Ω: 5 V Peak MAX

1 MΩ: 250 V Peak MAX

CH 1

250 V RMS

MAX INPUT:

+5 V MAX

CLK

PFI 0

AUX 0

PXIe-5163 Getting Started Guide | © National Instruments | 7

Table 2. Connectors

Signal Connector Type Description

CH 0 and CH 1 BNC female Analog input connection; digitizes data and triggers

acquisitions.

CLK IN SMB Imports an external reference clock or sample clock to

the oscilloscope.

PFI 0 SMB PFI line for digital trigger input/output, probe

compensation.

AUX 0 MHDMR Reference clock input, reference clock output,

bidirectional digital PFI, and 3.3 V power output.

Table 3. Access LED

Color Indications

Off The module is not yet functional or the module has detected a problem with a power

rail.

Amber The module is being accessed.

Green The module is ready to be programmed.

Table 4. Active LED

Color Indications

Off Module is not armed, triggered, or acquiring a waveform.

Amber The module is armed and waiting for a Reference (Stop) Trigger.

Green The module has received a Reference (Stop) Trigger. Also indicates that the module

is acquiring a waveform.

Red The module has detected an error. The LED remains red until the error condition is

removed. The following scenarios are examples of potential errors:

• Detected an unlocked condition on a previously locked PLL. A PLL that is

unlocked while in reset does not show an error.

• Unable to detect the external sample clock.

• Detected an overheating or overpowering error.

Note Certain driver interactions may cause the Active LED to flash red.

An error condition does not exist unless the Active LED remains red.

8| ni.com | PXIe-5163 Getting Started Guide

AUX 0 Connector Pinout

Table 5. AUX 0 Connector Pin Assignments

Pin Signal Signal Description

1 GND Ground reference for signals

2 CLK IN Used to import an external reference clock

3 GND Ground reference for signals

4 GND Ground reference for signals

5 CLK OUT Used to export the reference clock

6 GND Ground reference for signals

7 GND Ground reference for signals

8 AUX 0/PFI 0 Bidirectional PFI line

9 AUX 0/PFI 1 Bidirectional PFI line

10 GND Ground reference for signals

11 AUX 0/PFI 2 Bidirectional PFI line

12 AUX 0/PFI 3 Bidirectional PFI line

13 GND Ground reference for signals

PXIe-5163 Getting Started Guide | © National Instruments | 9

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de National Instruments

National Instruments

National Instruments PXIe-5632 Manual de usuario

National Instruments

National Instruments NI 9219 Manual de usuario

National Instruments

National Instruments PXIe-5654 Manual

National Instruments

National Instruments PXIe-4136 Manual de usuario

National Instruments

National Instruments FD-11613 Manual de usuario

National Instruments

National Instruments FD-11613 Manual de usuario

National Instruments

National Instruments PXI-4130 Manual

National Instruments

National Instruments PXIe-5668R Manual de usuario

National Instruments

National Instruments PXIe-4147 Manual de usuario

National Instruments

National Instruments PXI-5663 Manual

National Instruments

National Instruments SA1000X Manual de usuario

National Instruments

National Instruments NI PXIe-1491 Manual de usuario

National Instruments

National Instruments NI PXIe-5105 Manual de usuario

National Instruments

National Instruments USB-6210 Manual de usuario

National Instruments

National Instruments NI PXIe-4138 Manual

National Instruments

National Instruments NI 6601 Manual de usuario

National Instruments

National Instruments 4350 Manual de usuario

National Instruments

National Instruments NI 5911 Manual de usuario

National Instruments

National Instruments NI PXI-562X Manual de usuario

National Instruments

National Instruments PXIe-5667 Manual de usuario

National Instruments

National Instruments 9235 Manual de usuario

National Instruments

National Instruments NI 9263 Manual de usuario

National Instruments

National Instruments CMS-9024 Manual de usuario

National Instruments

National Instruments PXIe-5622 Manual

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario