NARGESA TS10 Manual de usuario
INSTRUCTIONS BOOK
PRADA NARGESA, S.L
Ctra. de Garrigàs a Sant Miquel s/n · 17476 Palau de Santa Eulàlia (Girona) SPAIN
Tel. +34 972568085 · [email protected] · www.nargesa.com
WELD POSITIONER
TS10
Thank you for choosing our machines
www.nargesa.com
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 2
INDEX
1. CHARACTERISTICS OF THE MACHINE ...............................................................................
1.1. Identification of the machine .......................................................................................
1.2. Dimensions .................................................................................................................
1.3. Description of the machine ..........................................................................................
1.4. Identification of the components .................................................................................
1.5. General characteristics ...............................................................................................
2. TRANSPORT AND STORAGE ...............................................................................................
2.1. Transport .....................................................................................................................
2.2. Storage conditions ......................................................................................................
3. INSTALMENT AND STARTING UP ........................................................................................
3.1. Location of the machine ..............................................................................................
3.2. Admissible outer conditions ........................................................................................
3.3. Connection to the power supply ..................................................................................
4. INSTRUCTIONS FOR USE .....................................................................................................
4.1. Panel description .........................................................................................................
4.2. Introduction .................................................................................................................
4.3. Feeding of the Positioner TS10 ...................................................................................
4.4. Activation of the Positioner TS10 ................................................................................
4.5. Memories of continous welding ...................................................................................
4.6. Memories of discontinous welding ..............................................................................
4.7. Robot mode .................................................................................................................
4.8. Memories of continous welding at robot mode ............................................................
4.9. Memories of discontinous welding at robot mode .......................................................
5. WARNINGS .............................................................................................................................
TECHNICAL ANNEX
3
3
3
3
4
5
6
6
6
7
7
7
7
8
8
10
10
10
11
12
14
15
16
19
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 3
1. CHARACTERISTICS OF THE MACHINE
1.1. Identification of the machine
1.2. Dimensions
Picture 1. External dimensions of the Weld positioner
1.3. Description of the machine
TS10 has been designed to weld different circular parts in different positions and kinds of welding.
TS10, is according to the European regulations and normative for the manufacturing of machinery
If an accident occurs by negligence of the operative, for not following the safety rules exposed
on this manual, PRADA NARGESA S.L will not accept any responsibility.
Trademark Nargesa
Type Weld positioner
Model TS10
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 4
1.4. Identificación de los componentes
Picture 2. Nomenclature and position of components
Connection for the
welding pincers
Oparation pedal
Encoder hose
Potenciometer to regulate
turning speed
LED’S light pilots
Slant regulation handle
Engine hose
Turning plate
Motor reducer
Emergency stop
Information display
Operations keyboard
Main switch
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 5
Picture 3. Features plate
1.5. General characteristics
Motor reducer 0,12 KW / 0,16 CV
2 phased tension 230 V
Speed 60º/s
Route of the programmable bench 0º - 360º
Slant regulation 0º - 100º
Welding type Continous or discontinous
Horizontal maximum capacity 75 Kg
Vertical maximum capacity 55 Kg
Round plate diemeter 395 mm
Plate thickness 10 mm
Bench height 790 mm
Dimensions 520x640x790 mm
Weight 61 Kg
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 6
2. TRANSPORT AND STORAGE
2.1. Transport
Transport with no elevation will be carried out by using a forklifting truck.
Picture 4. Transportation of the machine
2.2. Storage conditions
TS 10 must be placed in a site with the following requirements:
* Humidity between 30% and 95% without water condensation.
* Temperature from -25 to 55ºC or 75ºC for length of time no longer than 24h
* It is advisable not to pile up machines or heavy objects on top of them.
* Do not dismantle for storage.
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 7
IMPORTANT: This machine must be connected to a socket with ground connection.
3. INSTALMENT AND STARTING UP
3.1 Location of the machine
The machine will be properly placed so it doesn have to be moved, in case this is not possible then follow
the steps described in the transport section (nº2). It will be put in a flat surface to avoid vibrations and
movements of it during performance. It is possible to fix the machine by using bolts since it is provided with
a lower base or foot with 6 holes as it is shown in the picture.
Figura 5. Puntos de anclaje de la máquina
3.2. Admissible outer conditions
- Environmental temperature between +5ºC and +40ºC without exceding an average temperature of +35ºC
for the 24h
- Humidity from between 30% and 90% without water condensations.
3.3 Connection to the power supply
TS10 is equipped with a 230v and 0.12 kW single phased engine to be connected to a 230v power supply.
It must be connected to an only power supply in the indicated source.
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 8
4. INSTRUCTIONS FOR USE
4.1. Panel description
Picture 6. Control panel of the Welding Positioner.
Potenciometer to
regulate turning
speed
Emergency button
Information display
LED’S light pilots
Operations keyboard
Main switch
INSTRUCTIONS BOOK OF WELD POSITIONER TS10 9
NUMERICAL FUNCTION KEYS TO INTRODUCE DATA
KEY TO CONFIRM OR VALIDATE DATA
ESCAPE KEY TO RETURN MAKE ONE STEP BACK
ARROWS TO SELECT UPWARDS DIRECTION
ARROWS TO SELECT DOWNWARDS DIRECTION
KEY TO ACCEDE THE CONTINOUS WELDING MEMORIES MENU
KEY TO ACCEDE THE DISCONTINOUS WELDING MEMORY MENU
KEYS FUNCTION DIN JUST FOR THE USE OF THE ROBOT
INDICATES THE TURNING DIRECTION OF THE PLATE TO THE RIGHT
INDICATES THE TURNING DIRECTION OF THE PLATE TO THE LEFT
IT ALLOWS THE ACCESS TO THE TIME PARAMETER OF
STARTING OF THE WELDING PROCESS (WELDING STOKING TIME)
IT ALLOWS THE ACCESS TO OVERLAPPING PARAMETER
(IT SURPASSES WELDING FROM 360º)
IT ALLOWS ACCESS TO PERFORMANCE OF THE TS-10
WITH A WELDING ROBOT
Tabla de contenidos
Manuales populares de Accesorios de soldadura de otras marcas
Miller Electric
Miller Electric OM-842 Manual de usuario
Miller
Miller A-200 Series Manual de usuario
Abicor Binzel
Abicor Binzel ABIMIG WT Series Manual de usuario
optrel
optrel lifeflip autopilot Manual de usuario
Miller
Miller MIGmatic M-25 Manual de usuario
Tregaskiss
Tregaskiss TOUGH GUN TT3 Reamer Manual de usuario
