NAPCO EXPRESS XP-600 Manual de usuario

Usin

Your

XP-600

Security System

$50('

5($'<

6<67(0

),5(

=21( 

=21( 

=21( 

=21( 

=21(



=21( 

NAPCO

Oi218a

page 1 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

1Bell / Battery Test

Test your bell or siren by pressing



followed by



.This

will cause the bell, or siren to sound for 2 seconds and also

initiate a test of the battery .

2Central Station Communication Test

(This test should only be performed on weekends or at a

time designated by your alarm company)

1. Notify Central Station of the impending test.

2. Secure all zones to light Ready Light on your keypad.

3. Enter your user code to Arm the system.

4. Violate your alarm by opening a window / door etc.

5. The siren or bell should sound and the system will send

the alarm signals to the Central Station

6. Enter you user code to silence the bell or sounder.

7. Call Central Station to insure that the alarm signals were

received properly.

Introduction

System Information

Central Station Phone Number: ____________________

Central Station Account Number: ____________________

For Service Call: ____________________

Entry Delay: ____________________

Exit Delay: ____________________

Alarm Time-out: ____________________

Important - Test Your System Weekly !

Table of Contents

Keypad Controls and Indicators ................................ 4

Arming your System (When Leaving) ....................... 5

Protecting Yourself While Home ............................... 6

Emergency Keys ....................................................... 7

Disarming the System ............................................... 8

Silencing an Alarm..................................................... 8

Resetting a Fire Alarm............................................... 8

Fire Protection .......................................................... 9

Special Functions .................................................... 11

System Troubles ....................................................... 12

Programming User Codes ......................................... 14

Glossary ................................................................... 15

Oi218a

page 3 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

$50('

5($'<

6<67(0

),5(

=21( 

=21( 

=21( 

=21( 

=21(



=21( 

ad Controls and Indicators

Read

ht will light when all zones are secure

and system is ready to be Armed.

AC Li

ht will light to indicate that AC Power

is present.

Fire Alarm Li

ht will flash and the Keypad

sounder will beep when system is in a Fire Alarm

Condition (See Silencing a fire Alarm, Page 8)

Zone Li

hts

(

1 through 6) will light to indicate

that the corresponding Zone is open, and will

flash to indicate a zone in alarm.

Armed Li

ht will light when system is Armed,

and will flash when system is in Alarm

Key - used to reset Fire Zone, clear miss-

entered codes, reset Alarm Memory, etc..

System Light will light and the Keypad sounder

will pulse to indicate that a system trouble is pre-

sent.(See System Troubles, Page12)

Key Press to display any present

System troubles. Only available when

System Light is lit.

(See System troubles, Page 12)

Emergency Keys Press

simultaneously to signal

an emergency condition.

Press )+)for Fire,

$+$for Auxiliary or

3+3for Police Emer-

gency. (Programmable)

Bypass Key Used to

bypass zones. Press

Bypass and the corre-

sponding zone number,

and then Arm system.

Key Used to enable

special functions and op-

tions. Press and then

the corresponding Spe-

cial Function number Op-

tion (See Special Func-

tions, Page 11)

Numerical Keys 1-9, 0. Used to enter

User Codes, Zone numbers, etc.

NAPCO

Oi218a

page 4 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

Arming Your System When Leaving

1Before armin

your system, make sure the Green Ready li

ht is ON. This indicates that all of your prot-

ective zones are secure. If any zones are open, the correspondin

Zone li

ht will be ON. Secure these

zones before proceedin

. If any zones cannot be secured, see Bypassin

Zones below.

2 Enter your user code. The Green Ready li

ht will

o out, the Red Armed li

ht will li

ht.

• If you make a mistake enterin

your code, press



and re-enter the code.

• If the FIRE light is on, the Fire zone has not been properly reset. Press



and enter the code.

(See Silencing a Fire Alarm, page 8)

3 Leave the premises through the Exit/Entry door. If the keypad gives a steady tone you have taken

too long. Enter your code again to disarm system and then re-enter code and leave.

Easy Arm

The Easy Arm feature allows the system to be armed by simply pressing



followed by



This will allow the easy arming of the system by someone who is not a regular system user.

Bypassing Zones

If an open zone cannot be immediately fixed it can be left unprotected, or

Bypassed

, while the rest of the

system is Armed. To Bypass a zone:

1Press



followed by the zone number to be Bypassed. The Bypassed Zone’s light will flash slowly.

2 Enter your user code. The Green Ready light will go out and the Red Armed light will light.

3 Leave the premises through the Exit/Entry door.

When the system is subsequently disarmed, all bypassed zones will be reset, ready to be armed again.

If it is necessary to bypass any inoperative zone(s), it is important to have the zone(s) repaired as soon as

possible. A bypassed zone does not provide any protection, compromising system security.

Arming Your System

FIRE

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

ARMED

Oi218a

page 5 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

Protecting Yourself While at Home

1 Before armin

your system, make sure the Green Ready li

ht is ON. This indicates that all of your

protective zones are secure. If any zones are open, the correspondin

Zone li

ht will be ON. Secure

those zones before proceedin

2 Enter your user code. The Green Ready li

ht will

o out, and the Red Armed li

ht will li

ht.

3Before your exit delay expires, press



to bypass any interior zones, deactivatin

devices such

as motion sensors, and allowin

free movement throu

hout the premises. The Zone li

ht of any

bypassed zones will flash slowly.

• Your system may have been pro

rammed for Automatic Interior Bypass , in which case it will reco

nize

that you have not left the premises and will automatically bypass any interior zones.

Instant Mode

Pressin



followed by



will cancel the Entry delay , activating the “Instant” mode. This is typically

done in the evening when all family members are home for the night. Instant Mode can be activated at any

time after the system has been armed. The Red Armed light will flash rapidly while in the Instant Mode.

Easy Exit (optional)

Your System may have been programmed to allow Easy Exit, which allows a user to exit the premises

with the system armed. By pressing



followed by



, the protection is removed from the Exit/ Entry

zone for 3 minutes. This will allow, for example, an early morning commuter to exit the house in the

morning, without having to disarm and rearm the system, waking the family.

Arming With a System Trouble Present (the 9System Light is Lit)

If the XP600 has a system trouble present, the

SYSTEM li

ht will be lit and the ke

pad sounder

pulsin

. If

ou cannot immediatel

clear the s

stem trouble, the s

stem can still be armed. Simpl

press



to view the trouble, press



ain to reset the trouble and then arm the s

stem.

For more information, refer to pa

e 12. Note: S

stem troubles should be repaired as soon as possible.

Armin

Your System

FIRE

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

ARMED

Oi218a

page 6 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

Emergency Buttons

The three sets of emergency buttons, if programmed, are always active whether the system is armed

or disarmed. Discuss these Buttons with your installer. The emergency signal will only be activated

when the two respective buttons are pressed at the same time.

Fire Alarm: Simultaneously press



to sound a fire alarm, and to alert the central

station of a fire emergency, if so programmed.

Auxiliary Alarm: Simultaneously press



to alert the central station of an auxiliary

emergency, if so programmed.

(The nature of this emergency alarm is to be determined by the installer)

Police Emergency: Simultaneously press



to sound a police emergency alarm, and to alert

the central station of a fire emergency, if so programmed.

Emergency Conditions





Fire

Emergency

Enabled?

Yes No



Auxiliary



Emergency

Enabled?

Yes No

Ambush Alarm

In the event that you are forced by an intruder to disarm your system, the ambush alarm can be

activated. Disarming the system with the Ambush Code will cause the system to disarm and

simultaneously send a silent ambush alarm signal to Central Station. If your system has the Ambush

feature enabled, the code assigned as the User 6 code will function as your Ambush Code.



Police



Emergency

Enabled?

Yes No

Ambush

Alarm

Enabled?

Yes No

Oi218a

page 7 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

Disarming Your System when Returning

1Enter your premises throu

h the Entry/Exit door. The keypad will sound a steady tone to remind you to

disarm the system before your Entry Delay time expires.

2 Enter your user code. The Red Armed li

ht will

o out, indicatin

that the system has been disarmed.

Note: If you make a mistake enterin

your code, press the



key and re-enter the code.

Alarm Indication

If the Red Armed li

ht is flashin

rapidly, an alarm occurred while you were away. Proceed with caution!

For your own protection, leave immediately and call authorities from a nei

hbor’s phone .

Silencing an Alarm

In the event that the system

oes into alarm due to a violated bur

lary zone, the bell or siren will sound and

the keypad sounder will also activate. To silence the system, enter your User code. The zone li

ht of the

zone which went into alarm will continue to flash until



is pressed to reset the alarm memory.

Silencing a Fire Alarm

In the event that the Fire alarm activates due to an violated smoke or fire detector, the bell or siren will

sound a distinct pulsatin

tone. The Red FIRE li

ht on the keypad will be flashin

, and the keypad sounder

will emit a pulsin

tone. If a Fire Alarm does occur:

1If a fire is in pro

ress, evacuate the premises immediately!Call the Fire Department from an outside phone.

2If there is no evidence of a fire, enter your User Code. The bell or siren will silence, and the FIRE li

ht on

the keypad will stop flashin

but will still be lit.

3Determine which device went into alarm. If you are protected by smoke detectors, the li

ht on the active

detector will be lit. Once it is determined which smoke detector is in alarm, press



to reset the fire zone.

4 If the Fire zone has reset properly, the FIRE li

ht on the keypad should

o out in approx. 30 seconds

If it does not

o out, press



ain in a few minutes. If the FIRE li

ht still does not

o out, call for

service.

Disarming Your System / Silencing an Alarm

FIRE

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

ARMED

Oi218a

page 8 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

Special Functions 

By pressing



followed by the appropriate key, (do not press simultaneously) these special functions and features

can be enabled:



Easy Arm (when system is disarmed)

The Easy Arm feature allows the system to be armed by

pressing



followed by



. This will allow the easy

arming of the system by someone who is not a regular

system user.



Easy Exit (when system is armed)

This function (if programmed) allows an occupant to leave

the premises without disarming the system. Pressing



followed by



while the system is armed will start a 3

minute period, during which you can leave through the

Exit/ Entry door.



Bell / Battery Test

Pressing



followed by



will cause the bell, or siren to

sound for 2 seconds. This will also initiate a test of your

battery to make sure it is adequately charged. The XP-600

also performs an automatic battery test very 24 hours



Access Output

If programmed, pressing



followed by



will activate

the Access Output which may be configured to open a door

strike, turn on lighting, or activate some other special

feature your installer has provided.



Instant Mode

Pressing



followed by



will cancel the Entry delay

and put the system into the “Instant” mode. This is typic-

ally done in the evening when all family members are home

for the night. When the system is disarmed, the Instant

mode will be canceled.



Chime Mode On / Off

Pressing



followed by



will activate / deactivate the

door chime. Activating this feature will cause any door

to beep the keypad sounder when it is opened.



Program Mode

Pressing



followed by



will enable the “Program

Mode”, which will allow you to program and erase user

codes. (see Programming user codes, page 14)



Keypad Sounder On / Off

Pressing



followed by



will deactivate / activate the

keypad sounder, depending on its present state. By

activating sleep mode on a keypad installed in a bedroom,

for example, you effectively turn off that keypad’s sounder.

However, any other keypads on the system will still sound

normally.

Oi218a

page 11 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

The XP600 is constantly monitoring its own components, as well as all critical services, such as AC Power

and the Telephone line, to insure that it is always ready to provide the protection for which it was designed.

When a system trouble does occur, it will caution you by lighting the yellow

SYSTEM light and beeping the

keypad buzzer. If you cannot immediately clear the system trouble, the system can still be used. Simply

press



to view the trouble as described below, and then arm the system.

In order to determine the nature of the trouble, press



, count the number of keypad beeps and observe

the number of the illuminated zone light. Refer to the following table to determine the cause of the trouble.

If there is more than one trouble to be viewed, pressing



will scroll to the next, and then exit the

SYSTEM mode if there are no additional troubles to view.

9System Troubles

Keypad Beeps or

SYSTEM Flashes Zone light

ON System Trouble

Condition Action

Beep

1 AC Power Failure This trouble will occur if AC power is not present. Make sure

system transformer is plugged into AC receptacle and check

circuit breaker, otherwise call installing company for service.

Beep

2 Low Battery If there has been a recent power failure, the battery may be

partially depleted and must be recharged by the control

panel. If the trouble does not go away in 24 hours, call in-

stalling company for service.

Beep

3 Communication

Failure The system was not able to report to central station. If this is

due to a temporary interruption in the telephone service, the

trouble can be cleared when the service is restored by press-

ing



. Otherwise, call installing company for service.

Beep

4 Telephone Line Cut The telephone line has failed. If telephone service has been

temporarily interrupted, the trouble will clear it is when re-

stored. Otherwise, call installing company for service.

Beeps

1 Bell/Siren Trouble There is a problem with the Bell or Siren. Call installing com-

pany for service.

FIRE

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

ARMED

Oi218a

page 12 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

9System Troubles

Keypad Beeps or

SYSTEM Flashes Zone light

ON System Trouble

Condition Action

Beeps

2 Fire Trouble A problem has been detected in the Fire Circuit.

Call installing company for service.

Beeps

3 Wireless Receiver

Trouble A problem has been detected with the wireless receiver.

Call installing company for service.

Beeps

4 Wireless Receiver

Jam A problem has been detected with a wireless receiver.

Call installing company for service.

Beeps

1-6 Wireless

Transmitter Low

Battery

The battery in a wireless transmitter is low and should be re-

placed. This transmitter is on the zone corresponding to the num-

ber of the lit zone light. The replacement battery for the GEM-

Trans2 door/window transmitter, GEM-PIR motion detector and

GEM-GB glass break detector is the Duracell DL123A. (2 re-

quired for the GEM-PIR and GEM-GB.) The GEM-DT Dual Tech-

nology Sensor requires C-Cell Duracell MN1400 batteries(4).

Warning: Replace batteries only with the same type as specified

above. Use of another battery may present a risk of fire or explosion.

Do not recharge or disassemble battery, or dispose of in fire.

Beeps

1-6 Wireless

Transmitter

Supervisory Failure

A problem has been detected with a wireless transmitter.

Call installing company for service

Beeps

1-4 Wireless Smoke

Detector Low Bat-

tery

The battery in a wireless smoke detector is low and should be

replaced. This wireless smoke detector should be marked with a

number corresponding to the number of the lit zone light. The

replacement batteries required are Duracell 9 Volt Alkaline (2).

Warning: Replace batteries only with the same type as specified

above. Use of another battery may present a risk of fire or explosion.

Do not recharge or disassemble battery, or dispose of in fire.

Beeps

1-4 Wireless Smoke

Detector Supervi-

sory Failure

A problem has been detected with a wireless smoke detector.

Call installing company for service.

Beeps

1-6 Zone Trouble Call installing company for service.

FIRE

SYSTEM

READY

ZONE 3

ZONE 1

ZONE 2

ZONE 5

ZONE 6

ZONE 4

ARMED

Oi218a

page 13 Tuesday, September 16, 1997 08:28

www.ealarm.com.my

Otros manuales para EXPRESS XP-600

Tabla de contenidos

Otros manuales de Sistema de seguridad de NAPCO

NAPCO

NAPCO FREEDOM64 Manual de usuario

NAPCO

NAPCO EXPRESS XP-600 Manual de instalación

NAPCO

NAPCO MAGNUM ALERT-825 Manual de usuario

NAPCO

NAPCO XP-400 Hoja de datos

NAPCO

NAPCO EXPRESS XP-600 Manual de usuario

NAPCO

NAPCO MAGNUM ALERT-725 Manual de usuario

NAPCO

NAPCO Magnum Alert-800 Manual de usuario

NAPCO

NAPCO MAGNUM ALERT-725 Manual de usuario

NAPCO

NAPCO MAGNUM ALERT-850 Manual de usuario

NAPCO

NAPCO FREEDOM F-64TP Manual de usuario

NAPCO

NAPCO FREEDOM - Manual de usuario

NAPCO

NAPCO MVA-1000 Manual de usuario

NAPCO

NAPCO XP-400 Manual de usuario

NAPCO

NAPCO SECURITY COMMAND CENTER Manual de usuario

NAPCO

NAPCO EXPRESS XP-600 Manual de usuario

NAPCO

NAPCO XP-400 Manual de instalación

NAPCO

NAPCO XP-400 Manual

NAPCO

NAPCO Gemini GEM-X255 Manual de usuario

NAPCO

NAPCO StarLink Connect Series Manual de usuario

NAPCO

NAPCO MAGNUM ALERT 1008e Manual de usuario

NAPCO

NAPCO EXPRESS XP-600 Manual de usuario

NAPCO

NAPCO PRO410 Manual de usuario

NAPCO

NAPCO Continental Access SUPER TWO CICP1300IOCOMBO Manual

NAPCO

NAPCO Magnum Alert-854 Manual de usuario

Manuales populares de Sistema de seguridad de otras marcas

Inner Range

Inner Range Concept 2000 Manual de usuario

Climax

Climax Mobile Lite R32 Instrucciones de montaje

CADDX

CADDX NX-6 Manual de usuario

FBII

FBII XL-31 Series Manual de usuario

Johnson Controls

Johnson Controls PENN Connected PC10 Manual de usuario

Aeotec

Aeotec Siren Gen5 Manual de usuario

Blaupunkt

Blaupunkt SA 2700 Manual de usuario

IDEAL

IDEAL Accenta Manual del propietario

AJAX

AJAX DoubleButton Manual de usuario

Swann

Swann SW-P-MC2 Manual de usuario

Ecolink

Ecolink Siren+Chime Manual de usuario

Digital Monitoring Products

Digital Monitoring Products XR150 Manual de usuario

EDM

EDM Solution 6+6 Wireless-AE Manual de usuario

Highway Safety Group

Highway Safety Group EA401 Manual de usuario

Siren

Siren LED GSM Manual de usuario

Detection Systems

Detection Systems 7090i Instrucciones de montaje

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manual de usuario

Siemens

Siemens FDM273 Manual de usuario