2. G E NE R AL DIR E C TIV E S AND R E F E R E NC E S
E LE C T R IC AL G R OUNDING S P E C IF IC ATIO NS
T he s ys tem’s power unit mus t a bs olutely be grounded. In the eve nt of a ma lfunction or a power unit failure, the grounding provides the pa th of leas t
resistance to any electrical current, minimizing the risk of electric s hock. T he power unit’s power cord has a length of 65’’ (1,65m) and is fitted with a
grounding wire and grounding pin. T he power unit‘s power cord mus t always be directly plugged into a s uitable electrica l outlet which is its elf properly
ins talled a nd properly grounded, in comformity with the current local elec trica l sta ndards .
Do not us e extens ion cord(s ) to c onnect the power unit to the electrical outlet.
WA R NING
Improper connection of the power unit grounding wire can
res ult in the risk of electric shock. If you are in doubt of a
proper grounding, contact a profes sionnal electrician. Do
not modify the power cord s upplied with this power unit. If
this power cord connector does not fit your electrical
outlet, have the proper electrical outlet ins talled by a
professionnal electrician.
This power unit is designed to be us ed on a nominal
electrical circuit of 15 A . 110-120 VAC in 60 Hz. The
power cord is fitted with a grounding pin. Make certain
that the power cord is plugged into an electrical outlet
having the same specifications. This appliance should be
used without an adaptor. This power unit s hould be
installed on its own independant circuit and breaker.
IMP OR TA NT
The manufacturer shall not be held responsible for
damages cause by the innapropriate us e of this sys tem.
The warranty does not cover the damages caused by an
innapropriate use of this system nor the problems res ulting
from an installation which does not meet the specifications,
nor any structural or functional alterations made to the
power unit. An innapropriate, not-recommended installation
of the s ys tem or the power unit made without respecting the
directives of this document will equally be considered as
misus e. All conditions and restrictions are s et forth in the
limited warranty and in the user manual. To optimize the
performances and the life of your Nadair power unit, it is
important to do regular maintenance and cleaning of the
filter according to the guidelines listed in this user manual.
G eneral guidelines to be res pec ted at all time
1. The power unit must be ins talled in a well ventilated area, protected from weathering and away from all sources of
heat.
2. This central vacuum s ystem is design for dry surfaces only and must not be used on wet surfaces nor be used in
any circumstances to pick up liquids or to clean wet carpets or any wet ground.
3. The filter cage mus be coverd at all time by the permanent filter during operation of the system.
4. The motor housing must never be obstructed in anyway to prevent damaging or overheating.
5. Do not use this sys tem to pick up mud or similar substances. To vacuum baking flower, talcum powder, cement or
gypsum dus t, will have for effect to obstruct and clog the filter media; you have to clean the filter s everal time
during and after such pick-ups. Otherwise the motor will overheat and may be damaged.
6. Do not attempt to shorten or modify the power cord in any way.
7. As a s afety measure, unplug the power cord prior to proceed to maintenance or s ervicing.
8. In order for the warranty to remain valid; any repairs or servicing on the power unit must only be performed by an
authorized s ervice center.
9. The position of the power unit must be so, that the power cord and electrical outlet are always easily acess ible.
10. P ertaining to the use of an electrified valve (110 VAC ) (intended for the connection of a current carrying hose and
electrically motorised brush):
-Only connect a current carrying hose to this wall valve
-Do not install a current carrying valve outdoors
-Do not use a damaged hose, bring in the hose for repair at an authorized service center.
Page 4
G eneral guidelines to be res pec ted at all time
1. The power unit must be ins talled in a well ventilated area, protected from weathering and away from all sources of
heat.
2. This central vacuum s ystem is design for dry surfaces only and must not be used on wet surfaces nor be used in
any circums tances to pick up liquids or to clean wet carpets or any wet ground.
3. The filter cage must be covered at all time by the permanent filter during operation of the system.
4. The motor housing must never be obstructed in anyway to prevent damaging or overheating.
5. Do not use this sys tem to pick up mud or similar substances. To vacuum baking flower, talcum powder, cement or
gypsum dus t, will have for effect to obstruct and clog the filter media; you have to clean the filter s everal time
during and after such pick-ups. Otherwise the motor will overheat and may be damaged.
6. Do not attempt to shorten or modify the power cord in any way.
7. As a s afety measure, unplug the power cord prior to proceed to maintenance or s ervicing.
8. In order for the warranty to remain valid; any repairs or servicing on the power unit must only be performed by an
authorized s ervice center.
9. The position of the power unit must be so, that the power cord and electrical outlet are always easily acess ible.
10. P ertaining to the use of an electrified valve (110 VAC ) (intended for the connection of a current carrying hose and
electrically motorised brush):
-Only connect a current carrying hose to this wall valve
-Do not install a current carrying valve outdoors
-Do not use a damaged hose, bring in the hose for repair at an authorized service center.
