MuxLab 100518 Manual de usuario
© Muxlab Inc. 2020 94-000951-A/SE-000951-A
USB 2.0 4-Port Extender Kit, 50M
Operation Manual
100518
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 1
SAFETY PRECAUTIONS
To ensure the best performance from the product, please read all instructions carefully before using the device.
Save this manual for future reference.
⚫Follow basic safety precautions to reduce the risk of fire, electrical shock and injury.
⚫Do not dismantle the housing or modify the module. It may result in electrical shock or burns.
⚫Do not open or remove the housing of the device as you may be exposed to dangerous voltage or other
hazards.
⚫To prevent fire or shock hazard, do not expose the unit to rain, moisture and do not install this product near
water. Keep the product away from liquids.
⚫Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls
or spills on to the housing, unplug the module immediately.
⚫Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
⚫Using supplies or parts not meeting the products’ specifications may cause damage, deterioration or
malfunction.
⚫Refer all servicing to qualified service personnel.
⚫Install the device in a place with adequate ventilation to avoid damage caused by overheat.
⚫Unplug the power when left unused for a long period of time.
⚫Information on disposal of devices: do not burn or mix with general household waste, please treat them as
normal electrical waste.
NOTICE: Please read this manual carefully before using this product.
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 2
Table of Contents
1.Introduction ......................................................................................................................................................... 3
2. Features............................................................................................................................................................... 3
3. Package Contents................................................................................................................................................ 3
4. Specifications ...................................................................................................................................................... 3
5. Panels Description............................................................................................................................................... 4
5.1 Transmitter unit ......................................................................................................................................... 4
5.2 Receiver unit .............................................................................................................................................. 5
6. Connection.......................................................................................................................................................... 6
7. Regulatory Compliance....................................................................................................................................... 7
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 3
1.Introduction
The USB 2.0 4-Port Extender Kit, 50M enables USB 2.0 connectivity over Cat5e/6 at data rates up to 480Mbps
& extends true USB up to 50m (164ft) over standard Cat5e/6 UTP. This USB 2.0 4-Port Extender Kit is true plug
and play, requires no additional software drivers, and is compatible with all major operating systems. The unit
supports a wide variety of USB extension applications including security, industrial control, digital signage,
scientific data acquisition and other implementations of USB standards.
2. Features
⚫Supports four (4) USB Peripheral devices.
⚫Extends USB devices up to 50m (164ft) over Cat5e/6 cable.
⚫Supports USB 2.0 high-speed, USB 1.1 full-speed and USB 1.0 low-speed.
⚫True plug and play, no driver installation required.
⚫Supports hot plug function.
⚫Compatible with major operating systems.
3. Package Contents
⚫One (1) Transmitter unit.
⚫One (1) Receiver unit.
⚫One (1) 5VDC Power adapter.
⚫One (1) USB 2.0 Type A/M to Type B/M Cable 0.6m.
Notes：Confirm that the product and accessories are all included. If not, please contact the supplier from which
you purchased the unit.
4. Specifications
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 4
5. Panels Description
5.1 Transmitter unit
1 2
3
4 5
No.
Name
Description
1
Host
This connector is used to connect the USB cable that is connected
to the USB port of the computer.
2
EQ
Use the DIP switch (see table 1 below) to adjust the equalization
level. The equalization level varies from EQ # 1 (MAX or higher) to
EQ # 3 (MIN or weaker) for the respective transmission length
from the longest possible range to the shortest distance.
3
RJ45 Link
Plug in a CAT-5/5e/ 6 cable (50m max) that must be connected to
the RJ-45 connector of the Receiver unit.
4
Power indicator
5
Signal indicator
DIP Switch Position
Description
PIN#1
PIN#2
ON []
OFF []
EQ#1 (MAX or Strongest)
OFF []
ON []
EQ#2
OFF []
OFF []
EQ#3 (MIN or Weakest)
ON []
ON []
Reserved
Table 1
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 5
5.2 Receiver unit
12
3 4
5 6
No.
Name
Description
1
USB 2.0
Device
These connectors are used to connect the USB cables that are
connected to the USB ports of the devices (keyboards, mice,
printers, storage devices, cameras, card readers, etc.).
2
EQ
Use the DIP switch (see table 1 above) to adjust the equalization
level. The equalization level varies from EQ # 1 (MAX or higher) to
EQ # 3 (MIN or weaker) for the respective transmission length
from the longest possible range to the shortest distance.
3
5VDC, 2A
Power jack.
4
RJ45 Link
Plug in a CAT-5/5e/ 6 cable (50m max) that must be connected to
the RJ-45 connector of the Transmitter unit.
5
Power indicator
6
Signal indicator
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 6
6. Connection
Connection Diagram
1. Connect a USB cable between the USB port of the computer and the "Host" port on the Transmitter. Note
that in addition to transmitting data, this connection also powers the Transmitter.
2. Connect a CAT 5e/6 cable (50m max) between the "RJ45 Link" connector of the Transmitter and the
Receiver.
3. Connect the Receiver's power supply to the electrical outlet.
4. Connect the USB cables that are connected to the USB ports of the devices (keyboards, mice, printers,
cameras, etc.) to the "USB 2.0 Device" ports on the Receiver.
5. Note that no configuration or driver installation is required.
USB 2.0 4-Port Extender Kit, 50M Operation Manual
© Muxlab Inc. 2020 7
7. Regulatory Compliance
Disclaimer
Information in this document is subject to change without notice. The manufacturer does not make any
representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document
and shall in no event be liable for any loss of profit or any other commercial damage, including but not limited
to special, incidental, consequential, or other damages.
No part of this document may be reproduced or transmitted in any form by any means, electronic or mechanical,
including photocopying, recording or information recording and retrieval systems without the express written
permission of the manufacturer.
All brand names and product names used in this document are trademarks, or registered trademarks of their
respective holders.
2321 Cohen Road, Saint-Laurent, Quebec, Canada. H4R 2N7
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: videoease@muxlab.com URL:
www.muxlab.com
Tabla de contenidos
Otros manuales de Extensor de MuxLab
MuxLab
MuxLab 500409 Manual de usuario
MuxLab
MuxLab 500457 Manual de usuario
MuxLab
MuxLab 100504 Manual de usuario
MuxLab
MuxLab 500771 Manual de usuario
MuxLab
MuxLab 500456 Manual de usuario
MuxLab
MuxLab 500771 Manual de usuario
MuxLab
MuxLab 500409 Manual de usuario
MuxLab
MuxLab 500759-TX Manual de usuario
MuxLab
MuxLab 500417 Manual de usuario
MuxLab
MuxLab 500041-WP-UK Manual de usuario
MuxLab
MuxLab 500758 Manual de usuario
MuxLab
MuxLab 500752 Manual de usuario
MuxLab
MuxLab 500401-WP-US Manual de usuario
MuxLab
MuxLab 500402 Manual de usuario
MuxLab
MuxLab 500460 Manual de usuario
MuxLab
MuxLab VideoEase 500090 Manual de usuario
MuxLab
MuxLab 500459 Manual de usuario
MuxLab
MuxLab 500754 Manual de usuario
MuxLab
MuxLab 500112 Manual de usuario
MuxLab
MuxLab Pro Digital 500452 Manual de usuario
