MUTOH PJ-1614NXE Manual de usuario

Rev. PJ16E-A-00

User's Guide

Grand-Format Inkjet Printer

PJ-1614NXE

PJ-2216NXE

Read This Manual Before Using The

Equipment.

April 2002

PJ16E-A-00d 1 MUTOH INDUSTRIES LTD.

Some contents of the Operation Manual are changed.

Make sure the following list shown below.

Page Item Description

p.2-4 Modify the list in “2.3.2

Rear section (PJ-1614

NXE)”

Delete: No.8 Dumper

p.2-7 Modify the description

of “Right of 4th line” in

“2.4.1 Normal”

False: Displays the remaining amount of roll media...

↓

True: Displays the approximate remaining amount of roll media...

p.3-8 Modify the procedure in

“3.4.1 Turning the

power ON”

Refer to sheet 5−6

p.3-9

−

p.3-11

Modify the procedure in

“3.4.2 Turning the

power OFF”

Refer to sheet 7−11

p.3-13

−

p.3-14

Modify the procedure in

“3.5 Refilling the ink –

Jet wash fluid”

Refer to sheet 12−13

p.3-18 Modify the following

items in “3.6.1 Attaching

roll media

(PJ-1614NXE)”

・NOTE

NOTE

Delete: The printable side of the roll media must be on the outside.

p.3-19 ・Modify the procedure Refer to sheet 14−15

Modify the following items

in “3.6.2 Loading roll

media (PJ-1614NXE)”

・Add the description

shown in the right to

NOTE

in Step 2

・When using the roll media such as the printable side is inside:

Set media detection to “OFF”

4.4.40 Media detection menu

p.3-22

−

p.3-25

・Modify the procedure Refer to sheet 16−18

p.3-27 Modify the following items

in “3.6.3 Attaching roll

media (PJ-2216NXE)”

・NOTE

NOTE

Delete: The printable side of the roll media must be on the outside.

・Modify the procedure Refer to sheet 19

p.3-30 Add the description shown

in the right to

NOTE

in Step 2

in “3.6.4Loading roll

media (PJ-2216NXE)”

・When using the roll media such as the printable side is inside:

Set media detection to “OFF”

4.4.40 Media detection menu

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 2 MUTOH INDUSTRIES LTD.

Page Item Description

p.3-34

−

p.3-35

Modify the following

items in “3.6.5 Setting

winding unit”

・Step 3

False: Pull out the roll media from the feed slot, and fix into place

with tape so that the leading edge is parallel with the media

tube.



True: Pull out the roll media from the feed slot, obtain a uniform

tension, and then fix the end of the media to the media

tube.

・Add NOTE

NOTE

Refer to sheet 20

p.3-36

−

p.3-37

Modify the procedure

in ”3.6.6 Setting media

type”

Refer to sheet 21

p.3-41 Modify the procedure

in ”3.7 Head cleaning

before printing”

Refer to sheet 22−23

p.3-45

−

p.3-46

Modify the procedure

in”3.8.3 Alignment”

Refer to sheet 24

p.3-47

−

p.3-48

Delete “3.8.5

Maintenance record”

―

p.4-6 Modify No.10 in “4.3.5

Criteria for the media

feed”

False: Printable side with inboard should not be allowed



True: Printable side with inboard is not guaranteed

p.4-8 Add “4.3.7 Installing

media holder plate”

Refer to sheet 25−26

p.4-11 Modify the setup items

of the Setup menu (5/5)

in “4.4.1 Setup menu”

Refer to sheet 27

p.4-12 Modify the descriptions in

“4.4.2 Origin setup menu”

Refer to sheet 28

p.4-14 Modify the descriptions in

“4.4.5 Media type menu”

Refer to sheet 29

p.4-15 Modify the descriptions in

“4.4.6 User media menu”

Refer to sheet 30

p.4-17 Modify the parameters in

“4.4.10 Thickness

menu”

False: 50μm−<300μm>−1500μm



True: 50μm−<100μm>−1000μm

p.4-18 Modify the parameters in

“4.4.12 Dryer menu”

False: OFF/50℃−<60℃>−80℃



True: OFF/50℃−<60℃>−70℃

p.4-25 Modify the parameters in

“4.4.27 Online timeout

menu”

False: OFF/2sec−<30sec>−800sec



True: < OFF>/2sec−30sec−800sec

p.4-30

−

p.4-31

Modify the descriptions in

“4.4.38 Utility menu”

Refer to sheet 31

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 3 MUTOH INDUSTRIES LTD.

Page Item Description

p.4-33 Add NOTE

NOTE

“4.4.43 Negative

pressure pump menu”

NOTE

 Adjust the working pressure of the negative pressure pump

when:

Printing becomes smeared or misprinted and cannot be

corrected by performing head cleaning; increase the

parameter

Ink drips from the print head face during ink replenishment;

decrease the parameter

p.4-34 Add NOTE

NOTE

to ”4.4.45 Write mode

menu”

NOTE

 When writing drawing data onto hard disks, the media must

be set. Plotting data is processed according to the size of the

set media. If media is not set, plotting data cannot be written

on the disks.

p.4-35 Add NOTE

NOTE

to ”4.4.46 re-plot menu”

NOTE

 When the plotting data is re-plotted, set media of the same

size of the media used when writing the plotting data.

Regardless of the size of the set media, the plotted data is

plotted in the same size used for the original media.

p.4-36 Add NOTE

NOTE

to ”4.4.47 File delete

menu”

NOTE

 Once files are deleted in the file deletion items, they cannot

be restored. If the deleted files are needed for reuse, load the

plotting data from the computer to the hard disk again.

p.4-37 Add NOTE

NOTE

to ”4.4.48 Re-name

menu”

NOTE

 The file name of the plotting data that is loaded from the

computer is always named "TEMPFILE000". To save the

loaded plotting data, change its file name in the rename

entry before loading the next plotting data.

p.4-46 Add “4.4.64 Winding

Unit Menu”

Refer to sheet 32

p.4-46 Add “4.4.65 Send Roll

menu”

Refer to sheet 32

p.4-46 Add “4.4.66 Maintenance

record menu

Refer to sheet 34−35

p.4-48

−

p.4-49

Modify the procedure

in ”4.5.3 Winding the

roll media”

Refer to sheet 36

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 4 MUTOH INDUSTRIES LTD.

Page Item Description

p.4-49 Modify the following items

in “4.5.4 Head cleaning”

・Headline

False: If the printed screen is smeared or misprinted, perform

cleaning of the print head surface and the nozzles (head

cleaning).



True: Clean the print head surface and the nozzles (head cleaning)

when:

・Printing becomes smeared or misprinted

Waiting mode lasts over 1 hour with the power source supplied

・Add NOTE

NOTE

Step 2

NOTE

 If printing problems are not corrected by increasing purge

mode to "high", clean off the print head surface using a

poly-nit wiper soaked in jet wash fluid then perform head

cleaning again.

p.5-9

−

p.5-11

Modify ”5.2.3 Replacement

of the ink filter”

Refer to sheet 37

p.5-11 Add “5.2.4 Replacement

of the print head and

CR motor”

Refer to sheet 38−39

p.5-12 Modify the second term

CAUTION

“5.3 Cleaning the printer”

CAUTION



Do not use the jet-wash fluid, thinner, Benzene,

alcohol, or other active agents except for the following

parts:



Inside the maintenance cover



Print head surface

Doing so may result a malfunction in the product.

p.5-13 Modify “(1) Cleaning

interval” in “5.3.2

Cleaning inside the

printer”

False: Clean once a month.



True: Clean once a week.

p.5-18

−

p.5-20

Modify the following items

in “5.4 Long term

storage cleaning”

・”(1) Cleaning interval”

False: When not using the unit for over 2 weeks…



True: When not using the unit for over a week…

・”(2) Cleaning procedure” Refer to sheet 40−42

p.6-8

−

p.6-9

Add the descriptions to

“6.3.1 Status messages”

Refer to sheet 43

p.7-3 Modify “Outer diameter

dimension: Depth “ in

“7.2.2 PJ-2216NXE

Unit specifications”

False: 720mm (28.3in.)

↓

True: 802mm (31.6in.)

Appendix

Modify “Onsite

Adjustment

Verification”

Refer to “Onsite Adjustment Verification”

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 5 MUTOH INDUSTRIES LTD.

3.4.1 Turning the power ON

p.3-8: Modify the procedures after step 3 as follows:

3. Put the purge plate on the purge stand.

NOTE

 The purge plate must be placed on the purge stand whenever the power is on, except in the case when

head cleaning is performed ( 4.5.4 Head cleaning)

If waste fluid comes into contact with the inside of the product, the product may malfunction.

 When setting the purge plate, make sure not to contact to the print head surface

No. Name

1 Purge stand

2 Purge plate

4. Close the front cover and the maintenance cover.

: (omitted)

8. After finishing initial setup operations, the product will enter the normal operating condition.

9. Using the attached syringe, soak up the ink collected in the print head cap, then transfer

to the container.

No. Name

1 Print head cap

2 Syringe

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 6 MUTOH INDUSTRIES LTD.

10. Keep the print head cap in the accessories box.

No. Name

1 Print head cap

2 Accessories box

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 7 MUTOH INDUSTRIES LTD.

3.4.2 Turning the power OFF

p.3-9−p.3-11 Modify the procedures as follows:

1. Follow “3.8 Test printing”, and perform nozzle check printing.

2. Verify if there is any clogging of nozzles, missing dots, or faint printing.

NOTE

 If printing quality declines, or if missing dots are evident after the nozzle check, the print heads need

to be cleaned.

See “4.5.4 Head cleaning” to perform head cleaning.

If turning the power OFF without head cleaning, the clogged nozzle may not restore.

3. Verify the following regarding the operational condition of the product.

There is no printing operation being performed.

The control panel is in a normal status.

4. Push the [POWER] key of the control panel, to turn the product OFF

NOTE

 The power is ON if the control panel displays the following conditions:

・The [POWER] key is in the pushed-in condition.

・The POWER lamp is lit (red)

Press the [POWER] key again to turn the power OFF.

F 1

F 3

F 2

F 4

ERROR

DATA

MEDIA SET

CANCEL ENTER

POWER

RECEIVE

PROCESS

5. The product will perform the power OFF operation.

Following message is displayed on the operation panel.









PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 8 MUTOH INDUSTRIES LTD.

6. Open the front cover and the maintenance cover.

CAUTION



When opening/closing the maintenance cover, be careful not to get fingers caught in the lid.

No. Name

1 Front cover

2 Maintenance cover

7. Put the purge plate down from the purge stand.

No. Name

1 Purge stand

2 Purge plate

PJ-1614NXE PJ-2216NXE OPERATION MANUAL ERRATA

April 2002

PJ16E-A-00d 9 MUTOH INDUSTRIES LTD.

8. Open the clip in front of the print head cap.

No. Name

1 Print head cap

2 Clip

9. Install the print head cap to the print head.

No. Name

1 Print head cap

2 Print head

10. Close the front cover and maintenance cover.

Close firmly until the covers are fixed into place.

No. Name

1 Front cover

2 Maintenance cover

Otros manuales para PJ-1614NXE

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Impresora de MUTOH

MUTOH

MUTOH RJ-6000 Series Manual de usuario

MUTOH

MUTOH Viper TX Manual de usuario

MUTOH

MUTOH XPJ-661UF Manual de usuario

MUTOH

MUTOH Unwinder Manual de usuario

MUTOH

MUTOH VJ-1608 Hybrid Manual de usuario

MUTOH

MUTOH Falcon Outdoor Jr. Manual de usuario

MUTOH

MUTOH PJ-2646NXE Manual de usuario

MUTOH

MUTOH VJ-1638UH Mark II Manual de usuario

MUTOH

MUTOH Osprey 75 Manual de usuario

MUTOH

MUTOH ValueJet VJ-1204 Manual de usuario

MUTOH

MUTOH VJ-1948WX Guía del usuario

MUTOH

MUTOH Viper Extreme Manual de usuario

MUTOH

MUTOH Rockhopper 3 Extreme Manual de usuario

MUTOH

MUTOH Viper TX Softsign Manual de usuario

MUTOH

MUTOH VJ-2638X Manual de usuario

MUTOH

MUTOH ValueJet VJ-1204 Instrucciones de funcionamiento

MUTOH

MUTOH Falcon RJ-8000 Manual de usuario

MUTOH

MUTOH XpertJet XPJ-1641SR Guía de instalación

MUTOH

MUTOH Osprey 75 Manual de usuario

MUTOH

MUTOH ValueJet VJ-1604W Manual de usuario

MUTOH

MUTOH ValueJet VJ-1638UH Manual de usuario

MUTOH

MUTOH VJ-1304 Manual de usuario

MUTOH

MUTOH ValueJet VJ-1624 Manual de usuario

MUTOH

MUTOH Spitfire 100 Extreme Manual de usuario

Manuales populares de Impresora de otras marcas

Lexmark

Lexmark 1400 Series Manual

Canon

Canon i70 Series Manual de usuario

Evolis

Evolis Elypso Manual de usuario

Kyocera

Kyocera FS-9530DN Manual de usuario

Canon

Canon LASER SHOT LBP-1210 Manual de usuario

Samsung

Samsung BIXOLON SRP-350plusF Manual de usuario

Canon

Canon PIXMA PRO-1 Series Manual de usuario

Canon

Canon PIXMA G3560 Guía de configuración

Dell

Dell Color Laser Printer 2130cn Manual de usuario

Tektronix

Tektronix Phaser 840 Manual de usuario

Epson

Epson ET-7750 Instrucciones de funcionamiento

Canon

Canon CLBR 460ps Manual de usuario

Eltron

Eltron P210 Guide Manual de usuario

Ricoh

Ricoh MD-P1 Manual de usuario

Epson

Epson SC-F7100 series Manual de usuario

Epson

Epson Stylus C40UX Manual de usuario

Canon

Canon imagePASS-A2 Manual de usuario

Canon

Canon S820D Manual de usuario