Murphy OS-77R Manual de usuario

GENERAL INFORMATION AND MOUNTING DIRECTIONS

OS77R-OS.PM5

EFFECTIVE: 12/93

Model OS-77R

Model OS-77R-I

Overspeed Speed Switch With Relay Output

WARNING

BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT

Disconnect all electrical power to the machine.

Make sure the machine cannot operate during installation.

Follow all safety warnings of the machine manufacturer.

Read and follow all installation instructions.

Installation Accessories

Hardware, tools, and optional equipment needed to in-

stall the model OS77R.

■Tools as needed for the system mounting, such as

drill and screw driver.

■18 ga. wire for extension and hook up.

■Set of wire terminating tools.

■Wire termination; such as ring or spade terminals.

DESCRIPTION

The OS77R is an Overspeed Shutdown Switch used

for protecting the engine from excessive operating speeds.

The unit monitors a frequency generated from a magnetic

pickup. The OS77R-I functions identically to the OS77R

but monitors engine speed from a distributor ignition.

If the unit senses an engine speed higher than the ad-

justable set point, the unit will cause the engine to shut

down.

SETTING THE MODEL OS77R SERIES

IMPORTANT: The the following instructions as-

sume terminal number 5 is grounded. Please refer to

wiring and mounting information before attempting to ad-

just the unit. These steps must be done before the fine

tuning can be accomplished. The following steps should

be followed for first time setup of unit.

A. Turn “OVERSPEED ADJ.” fully clockwise.

B. Remove the wire from terminal # 2 of the OS77R.

C. Start engine and run at the highest RPM desired.

This is the RPM at which the engine should be

shut down if exceeded.

D. Connect a Voltmeter (or test light) between Termi-

nal #1 (positive +) and Terminal # 2 (negative -) of

the OS77R. You should read “no voltage” (test

lamp will be OFF.)

E. Slowlyturn“OVERSPEEDADJ.”counter-clockwise

and STOP the INSTANT battery voltage is indi-

catedon the voltmeter(or the testlight comes ON.)

F. Slowly turn “OVERSPEED ADJ.” clockwise about

1/8 of an inch. Now, tighten the locknut on the

“OVERSPEEDADJ.”without disturbingthesetting.

G. Re-connect the wire to Terminal #2 on the OS77R.

This reconnects the OVERSPEED shutdown cir-

cuitry.

NOTE: If further adjustment is needed;

Turning the “OVERSPEED ADJ.” clockwise,

RAISES the shutdown point. This allows the en-

gine to run at a HIGHER RPM.

Turning the “OVERSPEED ADJ.” counter-clock-

wise LOWERS the shutdown point. This will shut

down the engine at a LOWER RPM.

NOTE: Relay contacts are between terminals 2 and 5.

WARNING:Performthe mounting operationwith

power source off. The OS77R module is de-

signed to be mounted in a flat panel. First, drill

the mounting holes as shown on the template

includedwiththe packing. Insert themodulefrom

the back side of the panel and install mounting

hardware.

WIRING INSTRUCTIONS

CSB

OS77R

BATTERY

SPECIFY

VOLTAGE

STARTER

RACK

PULLER

FUEL

VALVE

HOLD IN

PULL IN

WARRANTY

A two year limited warranty on materials and workmanship is provided with this Murphy product. Details are

available on request and are packed with each unit.

117

1234

5KEY SWITCH

CSB

OS77R 169PH

MAGNETO

BATTERY

SPECIFY

VOLTAGE

321

OS77R USED WITH AN

ENERGIZED TO RUN

(ETR) SOLENOID

Note: For distributor

ignition applications,

you may use a Model

OS77R-I. Simply con-

nect terminal three (3)

to the negative side of

the ignition coil. You

will not need a mag-

netic pickup with the

Model OS77R-1.

OS77R USED TO SHUT

DOWN A MAGNETO

IGNITION ENGINE.

Note: Battery power

must be available. Also

note, a Murphy Model

169 PH magnetic

switch is used in place

of a Model 117.

Este manual sirve para los siguientes modelos

Otros manuales de Cambiar de Murphy

Murphy

Murphy Dual Temperature SWICHGAGE MDTM89 Guía del usuario

Murphy

Murphy L971 Series Manual de usuario

Murphy

Murphy LLS Manual de usuario

Murphy

Murphy Tattletale BN204 Series Manual de usuario

Murphy

Murphy L1100 Series Manual de usuario

Murphy

Murphy Swichgage WD300 Series Manual de usuario

Murphy

Murphy SWICHGAGE 45PE Series Manual de usuario

Murphy

Murphy Low Pressure SWICHGAGE 20PWC Manual de usuario

Murphy

Murphy Lead Line Pressure Swichgage Instrument... Manual de usuario

Murphy

Murphy SWICHGAGE TP-8318N Manual de usuario

Murphy

Murphy Swichgage EG21 Series Manual de usuario

Murphy

Murphy Swichgage Shutdown Panels WAI Series Manual de usuario

Murphy

Murphy Swichgage Diagnostic Panel Kits W0162 Manual de usuario

Murphy

Murphy PowerView PVM Series Manual de usuario

Murphy

Murphy VS94 Manual de usuario

Murphy

Murphy TATTLETALE 518APH Instrucciones de funcionamiento

Murphy

Murphy Single Set Point Switch OS77 Series Manual de usuario

Murphy

Murphy Temperature SWICHGAGE SPL Manual de usuario

Murphy

Murphy Bilge Level Switch System BLSK1 Series Manual de usuario

Murphy

Murphy TATTLETALE Annunciators and Magnetic... Manual de usuario

Murphy

Murphy Lube Level Swichgage Instrument L129 Series Manual de usuario

Murphy

Murphy PSB Manual de usuario

Murphy

Murphy VS2 Manual de usuario

Murphy

Murphy EVS-A Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario