Murphy PV485 Manual de usuario

00-02-1018

2017-05-23

Section 78

PowerView®

ModelPV485

InstallationManual

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our

specifications and designs at any time. The latest version of this manual can be found at

www.murphybyenovationcontrols.com.

BEFORE BEGINNING INSTALLATION OF THIS MURPHY

PRODUCT:

Read and follow all installation instructions.

Please contact Enovation Controls immediately if you have

any questions.

A visual inspection of this product for damage during

shipping is recommended before installation.

It is your responsibility to ensure that qualified mechanical

and electrical technicians install this product.

Contact Enovation Controls’ Technical Service if you have any

questions or concerns at: +1 918-317-4100.

Table of Contents

Hardware Installation.................................................................................................................1

Inspecting Package Contents.......................................................................................1

Tools needed. ..............................................................................................................1

Dash-Mounted Installation............................................................................................1

Rear-Mounted Installation (Optional) ...........................................................................2

Wiring Instructions 4

PIN Specifications for AMPSEAL Style Connection.....................................................4

Accessories..................................................................................................................4

Configuration Information ........................................................................................................5

Specifications.............................................................................................................................6

Technical......................................................................................................................6

Environmental..............................................................................................................6

Mechanical...................................................................................................................6

Mounting Templates..................................................................................................................7

Dash-Mount Template..................................................................................................7

Rear-Mount Bracket Template.....................................................................................9

PV485 Connection with Power...............................................................................................11

(THIS PAGE INTENTIONALLY LEFT BLANK)

Section 78 00-02-1018

2017-05-23 - 1-

Hardware Installation

The following instructions will guide you through installing the PV485 display.

Inspecting Package Contents

Before attempting to install the product, it is recommended that you ensure all parts are

accounted for and inspect each item for damage (which sometimes occurs during shipping).

The items included in the box are:

Installation kit –P/N 78-00-0783 includes:

4 (8-32) mounting studs

4 (8-32) Keps Nuts

1 small bag

Tools needed.

Drill with 3/16” size bit

Jig Saw

Wrench or socket for (8-32) Keps nuts

Dash-Mounted Installation

Preparing the Dash

Determine the location of the PowerView 485 in the dash. Use the Installation Template

(included at the end of the manual) as a guideline to cut a hole in the dash to the specified

dimensions. Drill holes where indicated on the template for the mounting screws.

NOTE: When using the paper template from the manual, please be aware that if

you downloaded this document from the Murphy by Enovation Controls website,

the pdf file may not automatically print to scale. When submitting the file for print,

you will need to select “None” for Page Scaling. Check the accuracy of the

printed template by verifying the measurements labeled on the template are

correct.

If this manual was supplied with your product, the template will be correct.

Section 78 00-02-1018

2017-05-23 - 2-

Installing the Display

Place the back side of the display through the opening in the dash.

1. Use the 4 screws to line up the unit with the drilled holes.

2. Push the unit through the opening and screws through the

drilled holes until the back of the case is flush.

3. Use the Keps nuts provided to tighten unit to the dash. Use the

appropriate wrench or socket to tighten. Torque lock nuts to 8-

10 inch pounds.

Rear-Mounted Installation (Optional)

Attach the Rear-mount bracket (P/N 78-00-0815) to the backside of the

unit.

1. Use the 4 screws to line up the rear-mount bracket with the

drilled holes.

2. Push the unit through the opening and screws through the drilled

holes until the back of the case is flush.

3. Use the Keps nuts provided to tighten unit to the dash. Use the

appropriate wrench or socket to tighten. Torque lock nuts to 8-10

inch pounds.

Mounting Options

Screws

1. Use the Installation Template (included at the end of the manual)

as a guideline to cut a hole in the mounting plate to the specified

dimensions and drill holes where indicated on the template for

the mounting screws.

2. Place the display behind dash and line up the four mounting holes on the rear-mount

bracket with the holes in dash.

3. Install four 8-32 screws (not provided) and torque lock nuts to 8-10 inch pounds.

Section 78 00-02-1018

2017-05-23 - 3-

Studs

1. Use the Installation Template (included at the end of the manual) as a guideline to cut a

hole in the mounting plate to the specified dimensions and weld 8-32 studs where

indicated on the template for mounting.

NOTE: Weld Studs and nuts are not provided. 8-32 Keps Nuts, Lock Nuts, or Nuts with

lock washers would need to be used.

2. Place the display behind dash and line up the four 8-32 welded studs with the holes in

rear-mount bracket.

3. Torque lock nuts to 8-10 inch pounds.

Dimensions for Installation

Section 78 00-02-1018

2017-05-23 - 4-

Wiring Instructions

PIN Specifications for AMPSEAL Style Connection

Accessories

P/N 78-00-0824 –Wiring Harness, Loose leads, 24 inches

P/N 78-09-0077 –Programming Harness

Section 78 00-02-1018

2017-05-23 - 5-

Configuration Information

Follow these steps to download a custom configuration to the PV485 display:

Step

Action

Ensure that PowerVision is open on your computer.

Connect the PV485 to the computer with the programming harness.

NOTE: If PowerVision does not detect the display, go to the Adapter

Properties. Select IPV4 properties, then change the IP address to

192.168.0.1 and the Subnet mask to 255.255.255.0.

Create your custom configuration file within PowerVision.

Deploy the configuration file to the PV485.

Follow these steps to download a custom configuration using a USB drive:

Step

Action

Create your custom configuration file within PowerVision.

Save the file to a USB drive.

Connect the USB drive to the USB port on the connector provided with the

programming kit.

Turn off the PV485, and turn it back on while holding down display key 5 (the

button on the far right). Continue to hold the button a few more seconds, then

release. This will put the display into the bootloader.

Use the corresponding keys to the up/down arrows to find the desired file. Use the

corresponding right arrow key to select and continue. The right arrow turns green;

press again to confirm.

When the installation is complete, a check mark is displayed in the middle of the

screen. The PV485 will power cycle and boot to the new configuration.

Section 78 00-02-1018

2017-05-23 - 6-

Specifications

Technical

Display: Bonded 4.3” color transmissive TFT LCD

Resolution: WQVGA, 480 x 272 pixels, 16-bit color

Aspect Ratio: 16:9

Orientation: Landscape

Backlighting: LED, 900-1000 cd / m2 (30,000 hr lifetime)

Microprocessor: Freescale iMX35 32bit, 532Mhz

Operating System: QNX Real-Time Operating System

Flash Memory: 256 MB (expandable to 8GB)

RAM: 128 Mbytes DDR2 SDRAM

Operating Voltage: 6-32 VDC, protected against reverse polarity and load-dump

Power Consumption: 10W max

CAN: (1) CAN 2.0B

Serial: (1) RS485 (Modbus Master/Slave)

Protocols: J1939; FreeForm Can support

Connection: (1) 35-pin AMP seal connector (AMP776231-4)

Keyboard: 5 tactile buttons

USB: (1) USB 2.0 host (full speed)

Digital Inputs: (3) digital inputs

Digital Outputs: (4) low side open-drain, capable of sinking 500 mA

Analog Inputs: (6) total, (4) software configurable (0-5V, 4-20mA, Resistive) + Battery Voltage +

2nd Battery Voltage

Analog Outputs: (1) 0-5V

Frequency Inputs: (1) Alternator and Magnetic Pickup

Real-time Clock: with battery backup

Environmental

Operating Temperature: -40°C to +85°C

Storage Temperature: -40°C to +85°C

Protection: IP 67, front and back.

Emissions/Immunity: SAE J1113 or customer-specified; (CE) - EN61000-6-2, EN12895, ISO 13766

Vibration: Random vibration, 7.86 Grms (5-2000 Hz), 3 axis

Shock: ± 50G in 3 axis

Mechanical

Case Material: Polycarbonate/ABS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Murphy

Murphy

Murphy SELECTRONIC 1400 Series Manual de usuario

Murphy

Murphy LM500 Manual de usuario

Murphy

Murphy ATS-30-12 Manual de usuario

Murphy

Murphy TANKTEND BGT Series Manual del propietario

Murphy

Murphy ATS series Manual de usuario

Murphy

Murphy Voltmeter VM-12 Manual de usuario

Murphy

Murphy PowerView Analog Gages PVA20 Manual de usuario

Murphy

Murphy Temperature Scanner/Pyrometer SWICHGAGE TDX6 Manual de usuario

Murphy

Murphy Temperature Scanner/Pyrometer TDXM Manual de usuario

Murphy

Murphy EMS447 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario