Munters Green RTU RX Manual de usuario

Installation Manual

Green RTU RX Module

Climate Controllers

Ag/MIS/ImEn-2765-05/20 Rev 1.2

P/N: 116812

Green RTU

RX Module

Green RTU RX Module

User Manual

Revision: N.1.2 of 07.2020

Product Software: N/A

This manual for use and maintenance is an integral part of the apparatus together with the attached

technical documentation.

This document is destined for the user of the apparatus: it may not be reproduced in whole or in part,

committed to computer memory as a file or delivered to third parties without the prior authorization of the

assembler of the system.

Munters reserves the right to effect modifications to the apparatus in accordance with technical and legal

developments.

Index

Chapter page

1INTRODUCTION ------------------------------------------------------------------------------------------------------------------------------------------4

1.1 Disclaimer--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1.2 Introduction-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------

1.3 Notes -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

2RADIO RECEIVER MODULE INSTALLATION---------------------------------------------------------------------------------------5

2.1 Mounting the RX------------------------------------------------------------------------------------------------------------------------------------------------------------------

2.2 Connecting the Output Devices to the Radio Receiver Module--------------------------------------------------------------

2.3 Connecting the Output Devices to the Receiver Module Equipped with the Plug Connection

Format -----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

2.4 Connecting the Output Devices to the Receiver Module Equipped with the Output Wire Loom

2.5 Programming the Radio Receiver Module--------------------------------------------------------------------------------------------------------

2.6 Applying Power to the Radio Receiver Module--------------------------------------------------------------------------------------------

2.7 Resetting the Radio Receiver Module------------------------------------------------------------------------------------------------------------------

2.8 Installing the Protection Hood ----------------------------------------------------------------------------------------------------------------------------------

2.9 General Notes-------------------------------------------------------------------------------------------------------------------------------------------------------------------

3WARRANTY------------------------------------------------------------------------------------------------------------------------------------------------- 15

1Introduction

1.1 Disclaimer

Munters reserves the right to make alterations to specifications, quantities, dimensions etc. for production

or other reasons, subsequent to publication. The information contained herein has been prepared by

qualified experts within Munters. While we believe the information is accurate and complete, we make no

warranty or representation for any particular purposes. The information is offered in good faith and with

the understanding that any use of the units or accessories in breach of the directions and warnings in this

document is at the sole discretion and risk of the user.

1.2 Introduction

Congratulations on your excellent choice of purchasing a GREEN RTU Receiver Unit!

In order to realize the full benefit from this product it is important that it is installed, commissioned and

operated correctly. Before installation or using the device, this manual should be studied carefully. It is

also recommended that it is kept safely for future reference. The manual is intended as a reference for

installation, commissioning and day-to-day operation of the Munters Controllers.

1.3 Notes

Date of release: May 2020

Munters cannot guarantee to inform users about the changes or to distribute new manuals to them.

NOTE

the expressed written permission of Munters. The contents of this manual are subject to change

without notice.

2Radio Receiver Module Installation

•Mounting the RX

•Connecting the Output Devices to the Radio Receiver Module

•Connecting the Output Devices to the Receiver Module Equipped with the Plug Connection

Format

•Connecting the Output Devices to the Receiver Module Equipped with the Output Wire Loom

Format

•Programming the Radio Receiver Module

•Applying Power to the Radio Receiver Module

•Resetting the Radio Receiver ModuleInstalling the Protection Hood

•General Notes

2.1 Mounting the RX

•Always mount the radio receiver module in clear open air.

•Mount the module in the horizontal plain with the window facing downwards as shown in the

Figure 1 below.

Figure 1: Mounting the Receiver

•Mount the receiver module onto a stainless steel receiver bracket using the modules mounting

slot as shown in Figure 2 below. Insert an M5 machined screw through the hole provided in the

top of the modules mounting bracket and lock this in place with a machine nut to secure the

module.

Figure 2: Receiver Brackets

•Mount the receiver module along with its bracket on a solid pole or other suitable solid structure

as high is as practically possible. Refer to Figure 3 below as example.

Figure 3: Receiver on a Pole

•When mounting the receiver module and bracket to the outside of a building, make sure to

locate the module on the building wall that is facing the transmitter’s antennae. In built up areas

this may not be possible but test this location to make sure you obtain acceptable signal quality

before mounting the unit.

•It is generally best practice to locate the switching devices such as solenoids and relays as close

as possible to the receiver module. This will be explained in more detail under the “Connecting

the Output Devices to the Radio Receiver Module” section.

•NOTE!!!

oDo not mount the receiver module on any structure that is subjected to vibration. E.g.

Avoid mounting the receiver module on a valve riser assembly as the riser assembly is

subjected to vibration while water flow takes place.

oAvoid mounting the radio receiver module in a metal or concrete enclosure or structure.

Even a metal cage will negatively influence radio signal. It is acceptable to mount the

receiver module within a plastic enclosure as shown in Figure 4.

Figure 4: Receiver on Plastic

•Avoid mounting the radio receiver in any location where corrosive gases are present.

•Do not mount the receiver module underground.

•Do not mount the receiver module in any location that can become flooded.

•Avoid mounting the receiver module where it will be subjected to water jet/s. E.g. Do not mount

the unit directly next to a sprinkler where the jet of water being emitted by the sprinkler hits the

receiver module.

•Avoid locating the receiver module in dense vegetation and foliage.

•Make certain acceptable radio reception is achievable when locating a receiver module in the

vicinity of high voltage power lines.

2.2 Connecting the Output Devices to the Radio Receiver Module

•The Green RTU RX radio receiver module is available in two output connection formats.

oThe output plug format as shown in Figure 5 below

Figure 5: Plug Format

oThe output wire loom format as shown in Figure 6 below

Figure 6: Wire Loom Format

•It is advisable to locate the output devices to be switched by the radio receiver module, such as

solenoids and relays, as close to the receiver module as is practically possible. These output

devices are activated with a short DC pulse signal and long cable/wire run lengths between the

output device and the radio receiver module can be problematic (can cause intermittent

operation).

•We do not suggest that you exceed 5m in total cable/wire length between the radio receiver

module and the output device to be controlled. Use a wire size of 1.5mm² if you intend to locate

the output device/s away from the receiver module up to 5m away.

•The Green RTU RX radio receiver module uses a two wire 12VDC pulse signal of 60mSec in

length. Compatible output devices should be selected to meet this specification and tested

properly for reliable use with the radio receiver module. Consult with Munters for a list of

approved devices.

2.3 Connecting the Output Devices to the Receiver Module Equipped with the Plug

Connection Format

This version of the Green RTU radio receiver module is equipped with a 6 terminal pins and a plug (black

and blue) as shown in Figure 7 below.

Figure 7: Terminal Pins

Looking from the rear (the mounting slot end) of the radio receiver module the terminals are as follows:

•Terminal 1 – Common (Black)

•Terminal 2 – Common (Black)

•Terminal 3 – Output #1 (Blue)

•Terminal 4 – Output #2 (Blue)

•Terminal 5 – Output #3 (Blue)

•Terminal 6 – Output #4 (Blue)

Figure 8 below shows two solenoid valves that have wire to the radio receiver modules terminal plug. The

green wire (plus) from solenoid valve #1 is wired to the first blue terminal (terminal 3 being the closest

blue terminal to the black terminals). The green wire (plus) from solenoid valve #2 is wired to the second

blue terminal (terminal 4). The black wires (minus) are wired to the black terminals in no specific order.

The two black terminals are the same.

Figure 8: Solenoid Valves

Wiring the 3 and 4 output would entail connecting the green wire for the 3rd output device to terminal 5

(blue block) and the green wire for the 4th output device to terminal 6 (blue block). The black wires from

both output devices would connect to either terminal 1 or 2 (the black blocks).

Once the wiring of the output devices to the terminal connector has been completed the connector can be

plugged into the pins on the base of the radio receiver module as shown in Figure 9 below.

Figure 9: Connecting the Pins

CAUTION

We recommend to remove this terminal connector from the radio receiver module once a

year and to clean the pins on the module as well as to thoroughly clean the plug. Apply a

good quality anti rust inhibitor spray such as silicone before reattaching the connector to the

receiver module.

2.4 Connecting the Output Devices to the Receiver Module Equipped with the Output Wire

Loom Format

This version of the Green RTU radio receiver module is equipped with a short piece of 6 core cable which

is attached on one end to the radio receiver module using a waterproof joint. The other end of the cable

has 6 soldered tinted wire ends exposed with ends, ready for attaching to the output devices as shown in

Figure 9 below.

Figure 10: Output Wire Loom Format Wiring

The 6 wires are allocated as follows -

•Red: Common

•Black: Common Reserved (Reserved for future use. Remove the temporary heat shrink if you will

use this wire)

•Yellow: Output #1

•Blue: Output #2 (Reserved for future use. Remove the temporary heat shrink if you will use this

wire)

•Green: Output #3 (Reserved for future use. Remove the temporary heat shrink if you will use this

wire)

•White: Output #4 (Reserved for future use. Remove the temporary heat shrink if you will use this

wire)

It is recommended to make a waterproof connection between these wires and the output device wires.

This can be achieved by terminating the connections in an additional enclosure or using a waterproof gel

type connector such as the sample shown in Figure 11 below.

Figure 11: Termination

2.5 Programming the Radio Receiver Module

The Green RTU RX radio receiver module is programmed using a Hand Held Programmer. Information

relating to this process is available in a separate document titled “Green RTU RX Module Programming

Guide”. If you do not have this document on record, feel free to contact Munters and we will forward a

copy.

2.6 Applying Power to the Radio Receiver Module

The Green RTU radio receiver module makes use of a 3.6VDC 19A/Hr Lithium-thionyl Chloride battery to

power the unit. This battery pack is equipped with a wire loom and a connector socket as shown in Figure

12 below

Tabla de contenidos

Otros manuales de Controladores de Munters

Munters

Munters Farm Center Manual de instrucciones

Munters

Munters TRIO Manual de funcionamiento

Munters

Munters Trio Poultry Controller Manual de usuario

Munters

Munters Platinum Touch Manual de usuario

Munters

Munters IA0090 Manual de usuario

Munters

Munters TRIO Manual de funcionamiento

Munters

Munters Rotem Trio Manual de usuario

Munters

Munters TRIO Manual de usuario

Munters

Munters BA1701 Manual de usuario

Munters

Munters Green Field Manual de usuario

Munters

Munters Platinum Touch Manual de usuario

Munters

Munters MD2 Manual de usuario

Munters

Munters TRIO Manual de usuario

Munters

Munters CCU5000 Manual de instrucciones

Munters

Munters CO2 Sensor Manual de instrucciones

Munters

Munters MUX 2 Manual de instrucciones

Munters

Munters G2 Manual de usuario

Munters

Munters Farm Center Pro Manual de instrucciones

Munters

Munters Pig Guard Plus Expansion Manual de instrucciones

Munters

Munters Rotem RBU-27 SE Guía

Munters

Munters Farm Premium Manual de usuario

Munters

Munters SMART-8C Manual de instrucciones

Munters

Munters Element Manual de instrucciones

Munters

Munters Rotem Trio 20 Manual de funcionamiento

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario