MULTISPAN AMP-23 Manual de usuario

Power Supply

Operating

Temperature

Relative

Humidity

230V AC,50 Hz, Approx 4VA

0°C To 55°C

Up to 95% RH Non Condensing

Model

Size (mm)

Display

Panel Cutout

Input Current

72(H) X 72 (W) X 62 (D) mm

4 Digit/Line 7 seg 0.56”,red LED Display

68 X 68 mm

AMP-23

0.1 to 5AMP AC, (PRIMARY) CAT III

Protection

Level

(As per request)

IP-65 (Front side) As per IS/IEC 60529 : 2001

www.multispanindia.com

Page - 1AMP-23

CT RATIO SELECTION

OPERATING MANUAL

3 Phase Panel Meter

AMP-23

Technical Specification

1) Press & Hold key for 10 sec.

3) Press & Hold key for 2 Sec.

4) Display will show present CT Ratio value

5) If no key is press for 5 seconds CT Ratio Automatically save & Exit

6) Press key for 2 second page will be scroll condition. If again Press key

For 2 Second page will be hold condition.

7) From 5 to 100 CT Ratio increased by step 5 Amp.

From 100 to 1000 CT Ratio increased by step 25 Amp.

From 1000 to 2000 CT Ratio increased by step 50 Amp.

From 2000 to 6000 CT Ratio increase by step 500 Amp.

1) To Increase CT Ratio Press key.

2) To Decrease CT Ratio Press key.

2) Display will show  (CT Ratio).

R Y B

AMP 23

.

AMP-23

www.multispanindia.com

Page - 2

Connection Diagram

230V AC

50Hz,4VA

All safety related codifications, symbols and instructions that appear in this operating manual

or on the equipment must be strictly followed to ensure the safety of the operating personnel as

well as the instrument.

If all the equipment is not handled in a manner specified by the manufacturer, it might impair the

protection provided by the equipment .

=> Read complete instructions prior to installation and operation of the unit.

WARNING : Risk of electric shock.

Safety Precautions

Current: 0.1 To 5A AC, CAT III

Range

CT Selection up to 6000/5 Amp AC CAT III

R Phase Ampere

Y Phase Ampere

B Phase Ampere

Average Current

LED INDICATION

Mechanical Installation

Maintenance

1) Prepare the panel cutout with proper dimensions as show above.

2) Fit the unit into the panel with the help of clamp given.

3) The equipment in its installed state must not come in close proximity to any heating source,

caustic vapors, oils steam, or other unwanted process by products.

4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the

screws on the terminal block using the tightening torque of the range of 1.2 N.m.

5) Do not connect anything to unused terminals.

1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.

2) Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any

other cleaning agent.

3) Fusible resistor must not be replaced by operator.

85mm - 3.34 inches

MODEL A

72mm 72mm 68mm 68mm 3mm 59mm

D E

DIMENSIONS

R Y B

AMP 23

.

95mm - 3.75 inches

AMP-23

www.multispanindia.com

Page - 3

1) This equipment, being built-in-type, normally becomes a part of main control panel and in such case the

terminals do not remain accessible to the end user after installation and internal wiring.

3) Circuit breaker or mains switch must be installed between power source and supply terminal to

facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be

installed at convenient place normally accessible to the operator.

4) Use and store the instrument within the specified ambient temperature and humidity ranges as

mentioned in this manual.

Installation Guidelines

2) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product

or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator.

3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires

should have insulations capacity made of at least 1.5kV.

2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of

equal size shall be made with shortest connection.

4) When extending the thermocouple lead wires, always use thermocouple compensation wires for wiring

for the RTD type, use a wiring material with a small lead resistance (5Ω max per line)and no resistance

differentials among three wires should be present.

1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the

wiring arrangement. Do not touch the terminals while power is being supplied.

5) A better anti-noise effect can be expected by using standard power supply cable for

the instrument.

Warning Guidelines

Note

AMP-23

www.multispanindia.com

Page - 4

Product improvement and upgrade is a constant procedure. So for more updated operating information and support,

Please contact our helpline : +91-9978991474/76/82 or Email at Ser[email protected] Ver: 01-2018

Tabla de contenidos

Otros manuales de Instrumento de medición de MULTISPAN

MULTISPAN

MULTISPAN AV-14DA Manual de usuario

MULTISPAN

MULTISPAN MFM-13 Manual de usuario

MULTISPAN

MULTISPAN AVH-14N Manual de usuario

MULTISPAN

MULTISPAN EM-1P Manual de usuario

MULTISPAN

MULTISPAN MS-1208A Manual de usuario

MULTISPAN

MULTISPAN AV-11V Manual de usuario

MULTISPAN

MULTISPAN VOLT-19N Manual de usuario

MULTISPAN

MULTISPAN AVH-14N Manual de usuario

MULTISPAN

MULTISPAN AV-11A Manual de usuario

MULTISPAN

MULTISPAN MFM 142DC-M1 Manual de usuario

MULTISPAN

MULTISPAN MI-631P Manual de usuario

MULTISPAN

MULTISPAN PI-54 Manual de usuario

MULTISPAN

MULTISPAN AVH-16 Manual de usuario

MULTISPAN

MULTISPAN PIC-38 Manual de usuario

MULTISPAN

MULTISPAN AV-41CT Manual de usuario

MULTISPAN

MULTISPAN MFM 13-M1 Manual de usuario

MULTISPAN

MULTISPAN MI-631P Manual de usuario

MULTISPAN

MULTISPAN AVH-14 Manual de usuario

MULTISPAN

MULTISPAN CT-1000 Manual de usuario

MULTISPAN

MULTISPAN DSM-14N Manual de usuario

MULTISPAN

MULTISPAN AMP 13 Manual de usuario

MULTISPAN

MULTISPAN AVH 13N Manual de usuario

MULTISPAN

MULTISPAN MVC-72N Manual de usuario

MULTISPAN

MULTISPAN MFM 14DC-M1 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario