MSI MS-6322M Manual de usuario
CHAPTER 1 INTRODUCTION
1-1
Chapter 1
INTRODUCTION
TheMS-6322M/MS-6322L Micro-ATXVAmainboardisahigh-
performance computer mainboard based on VIA®S3 ProSavage chipset.
The MS-6322M/MS-6322L is designed for the Intel®Socket processor for
inexpensive business/personal desktop markets.
TheVT8604/VT8605/86C370isahighperformance,costeffective
and energy sufficient SMA chipset for the implementation of AGP/ PCI /ISA
desktop personal computer systems with 66MHz, 100MHz and 133MHz CPU
host bus (Front Side Bus).
The VT82C686A integrates all system control functions such as
ACPI (Advances Configuration and Power Interface). The ACPI provides
more Energy Saving Features for the OSPM (OS Direct Power Management)
function. The VT82C686A chipset also improves the IDE transfer rate by
supporting Ultra DMA-33/66 IDE that transfers data at the rate 33/66MB/
sec. This mainboard which supports VIA®S3 ProSavage chipset is
ideal for high performance, high quality, high energy efficient and high
integration desktop AGP/PCI/ISA computer systems.
CHAPTER 1 INTRODUCTION
1-2
Mainboard Features
CPU
lSocket 370 for Intel®CeleronTM/Pentium®III (FC-PGA) processor and
Cyrix®III processor.
lSupports233MHz,266MHz,300MHz,333MHz,350MHz,400MHz,
450MHz,500MHZ,533MHz.,550MHz,667MHz,700Mhz,750MHz,
800MHz, or faster processor.
Chipset
lVIA®PM133VT8605/PL133VT8604chipset.(552BGA)
-FSB@133MHz
- Integrated S3 Savage4 2D/3D video accelerator
- AGP 4x and PCI Advanced high performance memory controller
-SupportPC100/133SDRAM,VCM,&ESDRAMtechnology
lVIA®VT686Achipset. (352BGA)
- Enhanced Power Management Features
-Integrated Super I/O (FDC, LPT, COM 1/2, and IR)
- Dual bus Master IDE Ultra DMA33/66
- Integrated Hardware Sounblaster
- Direct Sound AC97 Audio
-ACPI
ClockGenerator
l66.6MHz,100MHz,and133Mhz clocks are supported.
MainMemory
lSupport four memory banks using two 168-pin unbuffered DIMM.
lSupporta maximummemorysize of1GB(32M x8).
lSupport 3.3v SDRAM DIMM.
CHAPTER 1 INTRODUCTION
1-3
Slots
lOne AGP (Accelerated Graphics Port) slot (for MS-6322M only)
-AGP specification compliant
-Support AGP2.0 1x/2x/4x
lOne AMR (Audio Modem Riser) slot.
lTwo 32-bit Master PCI Bus slots and one 16-bit ISA slot (optional)
lSupports 3.3v/5v PCI bus Interface.
On-BoardIDE
lAnIDE controller on the VIA®VT82C686AChipset provides IDE HDD/
CD-ROM with PIO, Bus Master and Ultra DMA 33/66 operation modes.
lCan connect up to four IDE devices.
Audio
lAC-97’Codec
- 686A Chip Integrated
-AC’97 2.1Compliant
On-BoardPeripherals
lOn-BoardPeripherals include:
-1 floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M and
2.88Mbytes.
-2 serial ports (COMA + COMB)
- 1 parallel port supports SPP/EPP/ECP mode
- 4 USB ports (2 Rear Connectors/USB Front Pin Header)
-1IrDAconnectorforSIR/ASKIR/HPSIR.
- 1 VGA connector
- 1 Audio/Game port
CHAPTER 1 INTRODUCTION
1-4
BIOS
lThe mainboard BIOS provides “Plug & Play” BIOS which detects the
peripheral devices and expansion cards of the board automatically.
lThe mainboard provides a Desktop Management Interface(DMI) function
which records your mainboard specifications.
Dimension
lMicro-ATXForm Factor:24.5cm(L) x20.3cm(W)
Mounting
l6 mounting holes.
CHAPTER 1 INTRODUCTION
1-5
Mainboard Layouts
(A)MS-6322M Micro-ATX VAMainboard
PCI SLOT 2
PCI SLOT 1
ATX
Power Supply
S3
ProSavage
PM133
PGA370
DIMM 2
Top: Mouse
Bottom:
Keyboard
Top:Port 1
USB
IDE1
Bottom:
Port2
IDE2
FDD1
VT82C686A
CONN1
J8
CPUFAN
Top:LPT
Bottom:
COMA /VGA
Top: Midi/
GamePort
Bottom:
Line-Out
Line-In
Mic
J9
J15
BIOS
AGP Slot
BATT
+
DIMM 1
AMR JFP1
USB2
JMDM1
WOL1
COM 2
J12
SYSFAN
J14
J13
J11
CHAPTER 1 INTRODUCTION
1-6
(B)MS-6322L Micro-ATX VAMainboard
PCI SLOT 2
PCI SLOT 1
ATX
Power Supply
S3
ProSavage
PL133
PGA370
DIMM 2
Top: Mouse
Bottom:
Keyboard
Top:Port 1
USB
IDE1
Bottom:
Port2
IDE2
FDD1
VT82C686A
CONN1
J8
CPUFAN
Top:LPT
Bottom:
COMA /VGA
Top: Midi/
GamePort
Bottom:
Line-Out
Line-In
Mic
J9
J15
BIOS
BATT
+
DIMM 1
AMR JFP1
USB2
JMDM1
WOL1
COM 2
J12
SYSFAN
J14
J13
J11
CHAPTER 2 HARDWARE INSTALLATION
2-1
CPU
CPU
Chapter 2
HARDWARE INSTALLATION
Central Processing Unit: CPU
The mainboard operateswith Intel®CeleronTM/Pentium®III (FC-PGA)
processor. The mainboard uses a CPU socket called Socket 370 for easy
CPU installation. The CPU should always have a Heat Sink and a cooling
fan attached to prevent overheating.
3. Press the lever down to
complete the installation.
2. Locate Pin 1 in the socket
and look for the white dot or
cut edge in the CPU. Match
Pin 1 with the white dot/cut
edge. Then, insert the CPU.
It should insert easily.
OpenLever
Pin1
Sliding
Plate
White dot/
Cut edge
Close
Lever
1. Pull the lever sideways away
from the socket. Then, raise
the lever up to a 90-degree
angle.
Pin1
••
••
•CPU Installation Procedures
CHAPTER 2 HARDWARE INSTALLATION
2-2
If CPUClock = 66MHz
Core/Bus ratio = 3.5
then CPU core speed = Host Clockx Core/Bus ratio
= 66MHzx 3.5
= 233MHz
•CPU Core Speed Derivation Procedure
The jumper switch SW1 can be used to set the CPU Host Bus
Frequency Clock.
CHAPTER 2 HARDWARE INSTALLATION
2-3
•Fan Power Connectors: CPUFAN/SYSFAN
These connectors support system cooling fan with + 12V. It supports
three pin head connector. When connecting the wire to the connec-
tor, always take note that the red wire is the positive and should be
connected to the +12V, the black wire is Ground and should be
connected to GND. If your mainboard has System Hardware Monitor
chipset on-board, you must use a specially designed fan with speed
sensor to take advantage of this function.
For fans with fan speed sensor, every rotation of the fan will send out 2
pulses. System Hardware Monitor will count and report the fan rotation
speed.
Note: 1. Always consult vendor for proper CPU cooling fan.
2. CPU FAN supports the FAN control. You can install PC Alert
utility. This will automatically control the CPU FAN Speed according
to the actual CPU temperature.
CPUFAN
CPUFAN: Processor Fan
SYSFAN:SystemFan
+12V
CONTROL
SENSOR
SYSFAN
+12V
SENSOR
CONTROL
CHAPTER 2 HARDWARE INSTALLATION
2-4
Clear CMOS Jumper: J13
A battery must be used to retain the mainboard configuration in CMOS
RAM. Short 1-2 pins of JBAT1 to store the CMOS data.
Keep Data Clear Data
11
3
3
Note: You can clear CMOS by shorting 2-3 pin, while the system is off.
Then, return to 1-2 pin position. Avoid clearing the CMOS while
the system is on, it will damage the mainboard. Always unplug
the power cord from the wall socket.
22
1
3
J13
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa madre de MSI
MSI
MSI PRO B650M-A WIFI Manual de usuario
MSI
MSI A68HI AC Series Manual de usuario
MSI
MSI B75A-G43 series Manual de usuario
MSI
MSI H6M-P20 (G3) Manual de usuario
MSI
MSI MPG X570 GAMING PRO CARBONWIFI Manual de usuario
MSI
MSI G31M Series Manual de usuario
MSI
MSI PRO B650M-P Manual de usuario
MSI
MSI MEG Z790 GODLIKE Manual de usuario
MSI
MSI Z77IA-E53 series Manual de usuario
MSI
MSI MS-7357 (V1.X) Manual de usuario
MSI
MSI MS-5184 Manual de usuario
MSI
MSI Z170A TOMAHAWK Manual de usuario
MSI
MSI MPG Z590M Manual de usuario
MSI
MSI B550M PRO-VDH WIFI6 Manual de usuario
MSI
MSI K7 Master MS-6341 Manual de usuario
MSI
MSI RX480 Neo2 MS-7151 Manual de usuario
MSI
MSI MS-7203 Manual de usuario
MSI
MSI K9N2GM-FD - Motherboard - Micro ATX Manual de usuario
MSI
MSI 848P-V2 Series Manual de usuario
MSI
MSI P55-GD85 series Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
